PLF Series Fans Instruction Manual READ AND SAVE THESE INSTRUCTIONS WARRANTY CANARM Ltd. warrants every new fan to be free of defects in material and workmanship, to the extent that, within a period of one year from the date of purchase CANARM Ltd. shall either repair or replace at CANARM’s option, any unit or part thereof, returned freight prepaid, and found to be defective.
User’s Guide for All PLF Series Models Congratulations on the purchase of your new High Performance Plastic Fan. This fan is made of materials that ensure long lasting performance and is designed with features that make it one of the most efficient and easy to use and care for fans available today. Your fan comes completely assembled except for the metal turn clips that can be quickly assembled into the pre-drilled holes around the outside flanges of the fan.
ELECTRICAL CONNECTIONS If your fan is not provided with a cord, use the following procedure to wire the fan. ! WARNING WARNING: BE SURE POWER IS OFF AT THE ELECTRICAL PANEL BEFORE High Voltage, disconnect power before servicing. When bringing power to the fan, water-tight cable and connectors should be used. The cable will be brought to the motor through the slot provided in the top of the shutter and allowances in length of cable should be considered.
Chart #2 Table A - Minimum Wire Sizes for Three-Phase Motors Motor 25 to 50 Feet HP 200V 230V 460V 200V 1/8 14(18)* 14(18)* 14(18)* 14(18)* 1/6 14(18)* 14(18)* 14(18)* 14(18)* 1/4 14(18)* 14(18)* 14(18)* 14(16)* 1/3 14(18)* 14(18)* 14(18)* 14(16)* 1/2 14(16)* 14(18)* 14(18)* 12 3/4 14(16)* 14(16)* 14(18)* 12 1 14 14(16)* 14(18)* 12 1-1/2 12 14 14(18)* 10 2 12 12 14(18)* 8 3 10 12 14(18)* 6 100 Feet 230V 14(18)* 14(18)* 14(18)* 14(16)* 14(16)* 14 12 10 10 8 460V 14(18)* 14(18)* 14(18)* 14(18)* 14(18)* 14(1
BELT DRIVE FAN Belt drive fans are equipped with an automatic belt tensioner and cogged v-belt. The rotary tensioner will compensate for any wear or stretching of the belt. No adjustments should be necessary. Belt will however wear after extensive use. Fan performance will be sacrificed if worn belt is used. Listen for belt “squeeling” on startup. This would indicate that the belt requires changing or tightening. Tightening can be done by moving the screw location on the tensioner bracket.
14" Direct Drive No. 1 2 3 4 5 6 7 Component G1028 G1050 G1051-14 G1910-14 G2809-14B G2900-14 G2950-14 Description Turn Clip PLF Mount Arm Link Bracket PLF Motor Arm 14" Fan Guard PLF Housing 14" Shutter Assembly 14" 3/45 Rotair Blade Qty. 4 3 3 1 1 1 1 PLF 14-EVD 8 P1164-E 1/4 HP, 1625 RPM, 115/230V, 3.6/1.
16" Direct Drive No. 1 2 3 4 5 6 7 Component G1028 G1050 G1051-16 G1910-16 G2809-16B G2900-16 G2950-16 Description Turn Clip PLF Mount Arm Link Bracket PLF Motor Arm 16" Fan Guard PLF Housing 16" Shutter Assembly 16" 3/45 Rotair Blade Qty. 4 3 3 1 1 1 1 PLF 16-EVD 8 P1164-E3 1/4 HP, Max.
18" Direct Drive No. 1 2 3 4 5 6 7 Component G1028 G1050 G1051-18 G1910-18 G2809-18B G2900-18 G2950-18 Description Turn Clip PLF Mount Arm Link Bracket PLF Motor Arm 18" Fan Guard PLF Housing 18" Shutter Assembly 18" 3/4 Rotair Blade Qty. 4 3 3 1 1 1 1 PLF 18-FVD 8 P1164-F3 1/3 HP, Max.1625 RPM, 115/230V, 3.6/1.
20" Direct Drive No. 1 2 3 4 5 6 7 Component G1028 G1050 G1051-20 G1910-20 G2809-20B G2900-20 G2950-20 Description Turn Clip PLF Mount Arm Link Bracket PLF Motor Arm 20" Fan Guard PLF Housing 20" Shutter Assembly 20" 3/45 Rotair Blade Qty. 4 3 3 1 1 1 1 PLF 20-FVD 8 P1164-F3 1/3 HP, Max.1625 RPM, 115/230V, 3.6/1.
24" Direct Drive No. 1 2 3 4 5 6 Component G1028 G1050 G2983 G1051-24 G1910-24 G2809-24B Description Turn Clip PLF Mount Arm Link Bracket 24" Shutter Assembly PLF Motor Arm 24" Spiral Guard PLF Housing Qty.
36" Direct Drive No. 1 2 3 4 5 6 7 Component G1028 G1050 G1051-36 G1658-36GV G1900-36 G2809-36B P1170-36DP Qty. 4 4 4 1 1 1 1 Description Turn Clip PLF Mount Arm Link Bracket PLF Motor Arm 36" Galv. Shutter Assembly PLF36 Spiral Guard PLF Housing 1/2 HP, 825 RPM, 4 Lug Mount PLF 36-M 8 P3006-36D 36" S.S. Blade 3/25 1 36" Galv. Blade 3/25 1 36" Galv.
36" Belt Drive No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Component Qty. Description P1174-48BGE 1 HP, 1725 RPM, 115V, Reversable 1 G1028 4 Turn Clip G1883 1 Motor Mount Bracket 1 x 14.125 B.D. Shaft - 6 Lug Mount G1885 1 Rotary Tensioner Mount Bracket G1939 1 G1658-36V 1 36 GV.
Ventilateurs PLF Mode D’emploi VEUILLEZ LIRE ET GARDER CES INSTRUCTIONS GARANTIE Canarm Ltée. garantie ses nouveaux ventilateurs plf pour une période de 1 an contre toute défectuosité dans la fabrication et la main-d'oeuvre. Durant cette période Canarm aura l'option de réparer ou remplacer l'unité ou une pièce de l'unité si l'unité nous est retournée frais de port payé et nous trouvons une défectuosité.
Guide de l'Usage pour les Serie PLF Félicitations d'avoir fait l'achat d'un nouveau ventilateur à haut rendement en fibre de verre. Ce ventilateur a été construit de matériaux qui vous assureront un rendement de longue durée et ses caractéristiques en font un ventilateur des plus efficaces, facile d'opération et d'entretien disponible sur le marché aujourd'hui. Votre ventilateur vous est livré tout assemblé.
CONNECTIONS ELECTRIQUES Pour alimenter le courant au ventilateur, utiliser des cables et des connections resistants à l’eau. ! MISE EN GARDE Haut Voltage, veuillez fermer le courant avant de procéder à l’enretien. MISE EN GARDE: FERMEZ LE COURANT AU DISJONCTEUR AVANT DE PROCEDER AUX CONNEXIONS ELECTRIQUES. Le cable est amené au moteur à travers l’issue située au dessus du volet en laissant au cable une tolérance acceptable.
Tableau #2 Table A - Grosseur Minimum De Fil Pour Moteur A Trois Phases Moteur 25 à 50 Pieds 100 Pieds HP 200V 230V 460V 200V 230V 1/8 14(18)* 14(18)* 14(18)* 14(18)* 14(18)* 1/6 14(18)* 14(18)* 14(18)* 14(18)* 14(18)* 1/4 14(18)* 14(18)* 14(18)* 14(16)* 14(18)* 1/3 14(18)* 14(18)* 14(18)* 14(16)* 14(16)* 1/2 14(16)* 14(18)* 14(18)* 12 14(16)* 3/4 14(16)* 14(16)* 14(18)* 12 14 1 14 14(16)* 14(18)* 12 12 1-1/2 12 14 14(18)* 10 10 2 12 12 14(18)* 8 10 3 10 12 14(18)* 6 8 Table B - Grosseur Minimum De Fil Pou
VENTILATEUR A ENTRAINEMENT PAR COURROIE Les ventilateurs à entraînement par courroie sont munis d'un tensioneur de courroie automatique et d'une courroie d'engrenage en V. Le tensioneur rotatif compensera pour tout usure ou étirement de la courroie. Aucun ajustement n'est nécessaire. Cependant, la courroie s'usera après un usage prolongé. Le rendement du ventilateur sera en conséquence diminuer lorsque la courroie s'usera. Vérifiez s'il n'y aurait pas de bruit de grincement lors du démarrage.
14" Entraînement Direct No. 1 2 3 4 5 6 7 Piece G1028 G1050 G1051-14 G1910-14 G2809-14B G2900-14 G2950-14 Qté. 4 3 3 1 1 1 1 Description Pince à Visser Support De Monture PLF Bras De Monture PLF Grillage en Spirale 14" Boîtier PLF 14" Volet 14" Pale Rotair 14" 3/45 PLF 14-EVD 8 P1164-E 1/4 CV, 1625 RPM, 115/230V, 3.6/1.
16" Entraînement Direct No. 1 2 3 4 5 6 7 Piece G1028 G1050 G1051-16 G1910-16 G2809-16B G2900-16 G2950-16 Qté. 4 3 3 1 1 1 1 Description Pince à Visser Support De Monture PLF Bras De Monture PLF Grillage en Spirale 16" Boîtier PLF 16" Volet 16" Pale Rotair 16" 3/45 PLF 16-EVD 8 P1164-E3 1/4 CV, Max.
18" Entraînement Direct No. 1 2 3 4 5 6 7 Piece G1028 G1050 G1051-18 G1910-18 G2809-18B G2900-18 G2950-18 Description Pince à Visser Support De Monture PLF Bras De Monture PLF Grillage en Spirale 18" Boîtier PLF Volet 18" Pale Rotair 18" 3/4 Qté. 4 3 3 1 1 1 1 PLF 18-FVD 8 P1164-F3 1/3 CV, Max.1625 RPM, 115/230V, 3.6/1.
20" Entraînement Direct No. 1 2 3 4 5 6 7 Piece G1028 G1050 G1051-20 G1910-20 G2809-20B G2900-20 G2950-20 Description Pince à Visser Support De Monture PLF Bras De Monture PLF Grillage en Spirale 20" Boîtier PLF Volet 20" Pale Rotair 20" 3/45 Qté. 4 3 3 1 1 1 1 PLF 20-FVD 8 P1164-F3 1/3 CV, Max.1625 RPM, 115/230V, 3.6/1.
24" Entraînement Direct No. 1 2 3 4 5 6 Piece G1028 G1050 G2983 G1051-24 G1910-24 G2809-24B Description Pince à Visser Support De Monture PLF Volet 24" Bras De Monture PLF Grillage en Spirale 24" Boîtier PLF Qté.
36" Entraînement Direct No. 1 2 3 4 5 6 7 Piece G1028 G1050 G1051-36 G1658-36GV G1900-36 G2809-36B P1170-36DP Qté. 4 4 4 1 1 1 1 Description Pince à Visser Support De Monture PLF Bras De Monture PLF Volet 36" Galv. Grillage en Spirale 36" Boîtier PLF 1/2 CV, 825 RPM, 4 Supports PLF 36-M 8 P3006-36D Pale Inox. 36" 3/25 1 Pale Galv. 36" 3/25 1 Pale Galv.
36" Belt Drive No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Piece Qté. Description P1174-48BGE 1 HP, 1725 RPM, 115V, Reversable 1 G1028 4 Turn Clip G1883 1 Motor Mount Bracket 1 x 14.125 B.D. Shaft - 6 Lug Mount G1885 1 Rotary Tensioner Mount Bracket G1939 1 G1658-36V 1 36 GV.