MG3500 series Online Manual Troubleshooting English
Contents Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Problems with Network Communication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Problems with the Machine While Using with Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 The Machine Stopped Working Suddenly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printed Paper Curls or Has Ink Blots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Paper Is Smudged/Printed Surface Is Scratched. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Back of the Paper Is Smudged. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Vertical Lines Are Printed on the Sides of the Printout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About Errors/Messages Displayed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 If an Error Occurs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 A Message Is Displayed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 If You Cannot Resolve the Problem. . . . . . . . . . . . . . . . . . . . . . . . . . . .
1890. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 2100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 2101. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 2102. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
933. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 6936. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 6937. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 6938. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting The Machine Cannot Be Powered On Printing Does Not Start Paper Does Not Feed Properly/"No Paper" Error Occurs Print Results Not Satisfactory Ink Is Not Ejected Paper Jams If an Error Occurs Search Each Function Problems with Network Communication Problems with Printing Problems with Printing Quality Problems with Scanning Problems with the Machine Problems with Installation/Downloading About Errors/Messages Displayed If You Cannot Resolve the Problem 7
Problems with Network Communication Problems with the Machine While Using with Network Cannot Detect a Machine on a Network Other Problems with Network 8
Problems with the Machine While Using with Network The Machine Stopped Working Suddenly Ink Remaining Level Is Not Displayed on Printer Status Monitor of the Machine Printing Speed Is Slow Cannot Use the Machine on Replacing an Access Point or Changing Its settings 9
The Machine Stopped Working Suddenly Cannot Communicate with the Machine After the Network Settings Are Changed Cannot Communicate with the Machine over the Wireless LAN Cannot Print or Scan from a Computer Connected to the Network Cannot Communicate with the Machine After the Network Settings Are Changed Wait until the IP address is assigned to the computer. You may need to restart your computer. Search for the printer again after confirming a valid IP address is assigned to the computer.
Make sure that the channel set to the access point is valid to communicate with the computer, confirmed in Check 8. Check9 If not, change the channel set to the access point. Check10 Make sure that the firewall of the security software is disabled. If the firewall function of your security software is turned on, a message may appear warning that Canon software is attempting to access the network. If the warning message appears, set the security software to always allow access.
Ink Remaining Level Is Not Displayed on Printer Status Monitor of the Machine Use the printer driver with bidirectional communication. Select Enable bidirectional support in the Ports sheet of the properties dialog box of the printer driver.
Printing Speed Is Slow Check1 The machine may be printing out or scanning a large job issued from another computer. Make sure that the radio status is good and adjust the installation positions while monitoring the radio status with IJ Network Tool. Check2 Monitoring Wireless Network Status Make sure that there is no barrier or obstacle between the access point and the machine. Wireless communication between different rooms or floors is generally poor.
Cannot Use the Machine on Replacing an Access Point or Changing Its settings When you replace an access point, perform network setup of the machine again. Perform network setup again with the Setup CD-ROM or perform it again according to the instructions on our website. If the problem is not resolved, see below.
Cannot Detect a Machine on a Network Cannot Detect the Machine When Setting up Network Communication The Machine Cannot Be Detected in the Wireless LAN 15
Cannot Detect the Machine When Setting up Network Communication If the machine could not be detected on the network when setting up the network communication, confirm the network settings before redetecting the machine.
Cannot Detect the Machine during Wireless LAN Setup: Check 1 Are the computer and network device (router, access point, etc.) configured and can the computer connect to the network? Make sure that you can view any web pages on your computer. If you cannot view any web pages: Configure the computer and network device. For the procedures, refer to the instruction manuals supplied with the computer and network device, or contact their manufacturers.
Cannot Detect the Machine during Wireless LAN Setup: Check 2 Does the firewall function of your security software or operation system for computer interfere with setting up the network communication? The firewall function of your security software or operation system for computer may limit communications between the machine and your computer. Confirm the setting of firewall function of your security software or operation system or the message appearing on your computer.
Cannot Detect the Machine during Wireless LAN Setup: Check 3 Check the settings of the access point. Check the settings of the access point for the network connection such as IP address filtering, MAC address filtering, or DHCP function. For details on how to check the settings of the access point, refer to the instruction manual supplied with the access point or contact its manufacturer.
The Machine Cannot Be Detected in the Wireless LAN Check1 Make sure that the machine is turned on. Check2 Make sure that the Wi-Fi lamp is lit on the front side of the machine. If Wi-Fi lamp is off, Wireless LAN is inactive. Follow the procedure below to activate Wireless LAN. 1. Press and hold the Stop button until the Alarm lamp flashes 18 times. 2. Press the Color button. The Wi-Fi lamp is lit.
Check11 Make sure that the network settings of the computer are correct. Make sure that the computer can communicate with the printer and the access point over the wireless LAN. Make sure that Enable bidirectional support is selected in the Ports sheet of the properties dialog box of the printer driver. Check12 Check13 Make sure that the firewall of the security software is disabled.
Other Problems with Network Forgot an Access Point Name, SSID, or a Network Key The Message Is Displayed on the Computer Screen During Setup The Admin Password Set to the Machine Was Forgotten Checking Information about the Network Packets Are Sent Steadily How to Restore the Machine's Network Settings to Factory Default 22
Forgot an Access Point Name, SSID, or a Network Key Cannot Connect with an Access Point to Which a WEP/WPA/WPA2 Key Is Set (You Forgot the WEP/WPA/WPA2 Key) How to Set a WEP/WPA/WPA2 Key Cannot Connect with an Access Point to Which a WEP/WPA/WPA2 Key Is Set (You Forgot the WEP/WPA/WPA2 Key) For information on how to set up the access point, refer to the instruction manual provided with the access point or contact its manufacturer.
The Message Is Displayed on the Computer Screen During Setup The Enter Password Screen Is Displayed During Setup The Screen for Setting the Encryption Is Displayed After Selecting the Access Point in the Search Screen "You are connecting the machine to the non encrypted wireless network Is Displayed The Enter Password Screen Is Displayed During Setup The following screen is displayed if an administrator password is set to the machine which has already been set up.
The Admin Password Set to the Machine Was Forgotten Initialize the LAN settings. How to Restore the Machine's Network Settings to Factory Default After initializing the LAN settings, perform setup with the Setup CD-ROM or perform it according to the instructions on our website.
Checking Information about the Network Checking the IP Address or the MAC Address of the Machine Checking the IP Address or the MAC Address of the Computer Checking If the Computer and the Machine, or Computer and the Access Point Can Communicate Checking the Network Setting Information Checking the IP Address or the MAC Address of the Machine To check the IP address or the MAC address of the machine, print out the network setting information using the operation panel of the machine.
"XXX.XXX.XXX.XXX" is the IP address of the target device. If the communication is available, a message such as the following is displayed. Reply from XXX.XXX.XXX.XXX: bytes=32 time=10ms TTL=255 When Request timed out is displayed, the communication is not available. Checking the Network Setting Information To check the IP address or the MAC address of the machine, print out the network setting information using the operation panel of the machine.
Packets Are Sent Steadily While IJ Network Scanner Selector EX is enabled, it periodically transmits packets to check whether it can communicate with the machine over the network. When using the computer in a network environment other than the one used to set up the machine, disable IJ Network Scanner Selector EX. To disable IJ Network Scanner Selector EX, right-click the icon on the notification area on the desktop, then select Disable Canon IJ Network Scanner Selector EX.
How to Restore the Machine's Network Settings to Factory Default Important • Note that initialization erases all network settings on the machine, and printing or scanning operation from a computer over network may become impossible. To use the machine over network, perform setup with the Setup CD-ROM or perform it according to the instructions on our website. Follow the procedure below to initialize the network settings. 1. Press and hold the Stop button until the Alarm lamp flashes 17 times. 2.
Problems with Printing Printing Does Not Start Paper Jams Paper Does Not Feed Properly/"No Paper" Error Occurs Cannot Print Properly with Automatic Duplex Printing Copying/Printing Stops Before It Is Completed 30
Printing Does Not Start Make sure that the power plug is securely plugged in, then press the ON button to turn the machine on. Check1 While the ON lamp is flashing, the machine is initializing. Wait until the ON lamp stops flashing and remains lit. Note • When printing large data such as a photo or graphics, it may take longer to start printing. While the ON lamp is flashing, the computer is processing data and sending it to the machine. Wait until printing starts.
• In Windows 8 or Windows 7, right-click the "Canon XXX Printer" icon (where "XXX" is your machine's name), then select Printer properties. • In Windows Vista or Windows XP, right-click the "Canon XXX Printer" icon (where "XXX" is your machine's name), then select Properties. 4. Click the Ports tab to confirm the port settings. Make sure that a port named "USBnnn" (where "n" is a number) with "Canon XXX Printer" appearing in the Printer column is selected for Print to the following port(s).
Paper Jams When paper is jammed, the Alarm lamp flashes orange and a troubleshooting message is displayed on the computer screen automatically. Take the appropriate action described in the message. For details on how to remove the jammed paper, refer to Support Code List (When Paper Is Jammed). Note • You can confirm the actions against errors with Support Codes on your computer by searching a Support Code.
Paper Does Not Feed Properly/"No Paper" Error Occurs Check1 Make sure that paper is loaded. Loading Paper Check2 Make sure of the following when you load paper. • When loading two or more sheets of paper, flip through the paper before loading. • When loading two or more sheets of paper, align the edges of the sheets before loading. • When loading two or more sheets of paper, make sure that the paper stack does not exceed the paper load limit.
* After printing is finished, disable the setting for preventing double-feed of plain paper; otherwise, the setting is applied from the next time. • To set by using the operation panel Press and hold the Stop button until the Alarm lamp flashes 12 times, release the button, then press the Color button to enable the Prevent paper double-feed function.
Cannot Print Properly with Automatic Duplex Printing Check1 Is the setting for automatic duplex printing selected? Make sure that the Duplex Printing and Automatic check boxes are selected on the Page Setup sheet in the printer driver setup window. Duplex Printing Check2 Make sure that the actual size of the paper is suitable for automatic duplex printing. The sizes of media suitable for automatic duplex printing are A4 and Letter.
Copying/Printing Stops Before It Is Completed Check1 Is the paper loaded? Make sure that paper is loaded. If the machine has run out of paper, load paper. Check2 Do the printing documents have lots of photographs or illustrations? As printing large data such as photos or graphics takes time for the machine and the computer to process, the machine may appear to have stopped operating.
Problems with Printing Quality Print Results Not Satisfactory Ink Is Not Ejected 38
Print Results Not Satisfactory If the print result is not satisfactory due to white streaks, misaligned lines, or uneven colors, confirm the paper and print quality settings first. Check1 Do the page size and media type settings match the size and type of the loaded paper? When these settings are incorrect, you cannot obtain a proper print result. If you are printing a photograph or an illustration, incorrect paper type settings may reduce the quality of the printout color.
Cannot Print to End of Job Check1 Select the setting not to compress the printing data. If you select the setting not to compress the printing data with an application software you are using, the printing result may be improved. Click Print Options on the Page Setup sheet on the printer driver. Select the Do not allow application software to compress print data check box, then click OK. * Deselect the check box after printing is complete.
Part of the Page Is Not Printed Check When performing automatic duplex printing, the reason below is possible. When performing automatic duplex printing, the printable area at the top of the page will be 0.08 inches / 2 mm narrower than the usual. For this reason, the bottom of the page may not be printed. To prevent this, select the setting to reduce printing from the printer driver. Important • Reduced printing may affect the layout depending on your document.
No Printing Results/Printing Is Blurred/Colors Are Wrong/White Streaks No Printing Results Printing Is Blurred Colors Are Wrong White Streaks 42
Check1 Did you confirm the paper and print quality settings? Print Results Not Satisfactory Print the Nozzle Check Pattern and perform any necessary maintenance operations such as Print Head Cleaning. Check2 Print the Nozzle Check Pattern to determine whether the ink ejects properly from the print head nozzles. Refer to When Printing Becomes Faint or Colors Are Incorrect for the Nozzle Check Pattern printing, Print Head Cleaning, and Print Head Deep Cleaning.
Clean the platen glass. Cleaning the Platen Glass and Document Cover Check7 Make sure that the original is properly loaded on the platen glass. Loading Originals Check8 Is the original loaded with the side to be copied facing down on the platen glass? Check9 Did you copy a printout done by this machine? If you use a printout done by this machine as the original, print quality may be reduced depending on the condition of the original. Reprint from the computer if you can reprint from it.
Colors Are Unclear Check1 Is the Nozzle Check Pattern printed properly? Print the Nozzle Check Pattern to determine whether the ink ejects properly from the print head nozzles. Refer to When Printing Becomes Faint or Colors Are Incorrect for the Nozzle Check Pattern printing, Print Head Cleaning, and Print Head Deep Cleaning. • If the Nozzle Check Pattern is not printed correctly: After performing the Print Head Cleaning, print the Nozzle Check Pattern and examine the pattern.
Lines Are Misaligned Check1 Did you confirm the paper and print quality settings? Print Results Not Satisfactory Check2 Perform Print Head Alignment. If printed lines are misaligned or print results are otherwise unsatisfactory, adjust the print head position. Aligning the Print Head Note • If the problem is not resolved after performing the Print Head Alignment, perform Print Head Alignment manually referring to Aligning the Print Head Position from Your Computer.
Line Does Not Print or Prints Partially Check1 Is the Page Layout Printing performed or the Binding margin function used? When the Page Layout Printing or Binding margin function is being used, thin lines may not be printed. Try thickening the lines in the document. Check2 Is the size of the print data extremely large? Click Print Options on the Page Setup sheet on the printer driver. Then, set Prevention of Print Data Loss in the displayed dialog to On.
Image Does Not Print or Prints Partially Check1 Select the setting not to compress the printing data. If you select the setting not to compress the printing data with an application software you are using, the printing result may be improved. Click Print Options on the Page Setup sheet on the printer driver. Select the Do not allow application software to compress print data check box, then click OK. * Deselect the check box after printing is complete.
Printed Paper Curls or Has Ink Blots Printed Paper Has Ink Blots Printed Paper Curls Check1 Did you confirm the paper and print quality settings? Print Results Not Satisfactory Check2 If the intensity is set high, reduce the intensity setting and try printing again. If you are using plain paper to print images with high intensity, the paper may absorb too much ink and become wavy, causing paper abrasion. You can confirm the intensity using the printer driver.
Paper Is Smudged/Printed Surface Is Scratched Paper Is Smudged The Edges of Paper Are Smudged Printed Surface Is Smudged Printed Surface Is Scratched Check1 Did you confirm the paper and print quality settings? Print Results Not Satisfactory Check2 Is the appropriate type of paper used? Check the followings: • Check to see if the paper you are printing on is suitable for your printing purpose.
1. Roll up the paper in the opposite direction to the paper curl as shown below. 2. Check that the paper is now flat. We recommend printing curl-corrected paper one sheet at a time. Note • Depending on the media type, the paper may be smudged or may not be fed properly even if it is not curled inward. In such cases, follow the procedure described below to curl the paper outward within 0.1 inch / 3 mm (B) in height before printing. This may improve the print result.
If you are using plain paper to print images with high intensity, the paper may absorb too much ink and become wavy, causing paper abrasion. Reduce the intensity setting in the printer driver and try printing again. 1. Open the printer driver setup window. How to Open the Printer Driver Setup Window 2. On the Main sheet, select Manual for Color/Intensity, and then click Set.... 3. Drag the Intensity slide bar on the Color Adjustment sheet to adjust the intensity.
Back of the Paper Is Smudged Check1 Did you confirm the paper and print quality settings? Print Results Not Satisfactory Check2 Perform the Bottom Plate Cleaning to clean the inside of the machine. Cleaning the Inside of the Machine (Bottom Plate Cleaning) Note • When performing borderless printing, duplex printing, or too much printing, the inside may become stained with ink.
Vertical Lines Are Printed on the Sides of the Printout Check Is the size of the loaded paper correct? The vertical lines may be printed in the margin if the size of the loaded paper is larger than that you have specified. Set the paper size correctly according to the paper you loaded. Print Results Not Satisfactory Note • The direction of the vertical line pattern may vary depending on the image data or the print setting. • This machine performs automatic cleaning when necessary to keep printouts clean.
Colors Are Uneven or Streaked Colors Are Uneven Colors Are Streaked Check1 Did you confirm the paper and print quality settings? Print Results Not Satisfactory Check2 Print the Nozzle Check Pattern and perform any necessary maintenance operations such as Print Head Cleaning. Print the Nozzle Check Pattern to determine whether the ink ejects properly from the print head nozzles.
Aligning the Print Head Note • If the problem is not resolved after performing the Print Head Alignment, perform Print Head Alignment manually referring to Aligning the Print Head Position from Your Computer.
Ink Is Not Ejected Check1 When a FINE cartridge runs out of ink, replace it with a new one. Check2 Is the FINE cartridge installed properly? If the FINE cartridge is not installed securely, ink may not be ejected correctly. Open the paper output cover, then the head cover opens. Push up the ink cartridge lock lever to confirm that the FINE cartridge is installed properly. After confirming that the FINE cartridge is installed properly, close the paper output cover.
Problems with Scanning Problems with Scanning Scan Results Not Satisfactory Software Problems 58
Problems with Scanning Scanner Does Not Work ScanGear (Scanner Driver) Does Not Start Error Message Appears and the ScanGear (Scanner Driver) Screen Does Not Appear Cannot Scan Multiple Items at One Time Cannot Scan Properly with Auto Scan Slow Scanning Speed "There is not enough memory.
Scanner Does Not Work Check 1: Make sure that your scanner or printer is turned on. Check 2: Connect the USB cable to a different USB port on the computer. Check 3: If the USB cable is connected to a USB hub, remove it from the USB hub and connect it to a USB port on the computer. Check 4: Restart the computer.
ScanGear (Scanner Driver) Does Not Start Check 1: Make sure that MP Drivers is installed. If not installed, install MP Drivers from the Setup CD-ROM or the web page. Check 2: Select your scanner or printer on the application's menu. Important If your scanner or printer name is displayed multiple times, select the one that does not include WIA. Note The operation may differ depending on the application. Use the WIA driver when scanning from a WIA-compliant application.
Error Message Appears and the ScanGear (Scanner Driver) Screen Does Not Appear Check 1: Make sure that your scanner or printer is turned on. Check 2: Turn off your scanner or printer, then reconnect the USB cable and replug the power cord. Check 3: Connect the USB cable to a different USB port on the computer. Check 4: If the USB cable is connected to a USB hub, remove it from the USB hub and connect it to a USB port on the computer. Check 5: Make sure that MP Drivers is installed.
Cannot Scan Multiple Items at One Time Check 1: Make sure that the items are placed correctly. Placing Items (When Scanning from a Computer) Check 2: Check if you can properly scan one item. Some applications do not support multiple image scanning. In that case, scan each item individually.
Cannot Scan Properly with Auto Scan Check 1: Make sure that the items are placed correctly. Placing Items (When Scanning from a Computer) Check 2: Multiple items scanning may not be supported. Some applications do not support multiple image scanning. In that case, scan each item individually.
Slow Scanning Speed Check 1: To view the image on a monitor, set the output resolution to around 150 dpi. To print, set it to around 300 dpi. Resolution Check 2: Set Fading Correction, Grain Correction, etc. to None. Refer to "Image Settings" for your model from Home of the Online Manual for details. Check 3: In IJ Scan Utility, deselect the Correct slanted text document / Detect the orientation of text document and rotate image checkbox and scan again.
"There is not enough memory." Message Is Displayed Check 1: Exit other applications and try again. Check 2: Reduce the resolution or output size and scan again.
Computer Stops Operating during Scanning Check 1: Restart the computer, reduce the output resolution in ScanGear (scanner driver) and scan again. Refer to "Output Settings" for your model from Home of the Online Manual for details. Check 2: Delete unnecessary files to obtain sufficient free hard disk space, then scan again. Error message may appear if there is not enough hard disk space to scan and save, when the image size is too large (such as when scanning a large item at high resolution).
Scanner Does Not Work after Upgrading Windows Check: Disconnect the USB cable, then uninstall (delete) and reinstall MP Drivers and IJ Scan Utility. • Step 1: Uninstall MP Drivers. Refer to "Deleting the Unnecessary MP Drivers" for your model from Home of the Online Manual for how to delete MP Drivers. • Step 2: Uninstall IJ Scan Utility. • Windows 8: 1. Click the Settings charm > Control Panel > Programs > Uninstall a program. 2. Double-click Canon IJ Scan Utility. 3.
Note In Windows 7 and Windows Vista, a confirmation/warning dialog box may appear when installing, uninstalling, or starting up software. This dialog box appears when administrative rights are required to perform a task. If you are logged on to an administrator account, follow the on-screen instructions. • Windows XP: 1. From the Start menu, select Control Panel > Add or Remove Programs. 2. Select Canon IJ Scan Utility, then click Change/Remove. 3. When a confirmation appears, click Yes. 4.
Scanned Image Does Not Open Check: If the data format is not supported by the application, scan the image again and select a popular data format such as JPEG when saving it. Refer to the application's manual for details. If you have any questions, contact the manufacturer of the application.
Scan Results Not Satisfactory Scan Quality (Image Displayed on the Monitor) Is Poor Scanned Image Is Surrounded by Extra White Areas Cannot Scan at the Correct Size Item Is Placed Correctly, but the Scanned Image Is Slanted Scanned Image Is Enlarged (Reduced) on the Computer Monitor 71
Scan Quality (Image Displayed on the Monitor) Is Poor Check 1: Increase the scanning resolution if the image is jagged. Resolution Check 2: Set the display size to 100 %. Some applications do not display images clearly if the display size is too small. Check 3: If moire (stripe pattern) appears, take the following measures and scan again.
Correction, etc. in Image Settings on the Advanced Mode tab of ScanGear. Refer to "Image Settings" for your model from Home of the Online Manual for details. Check 7: If the color tone of images is different from the original document, take the following measures and scan again. • On the Advanced Mode tab of ScanGear, set Image Adjustment in Image Settings to None. Refer to "Image Settings" for your model from Home of the Online Manual for details.
Scanned Image Is Surrounded by Extra White Areas Check: Specify the scan area. (Auto Crop) in whole image view of ScanGear (scanner driver) to automatically Click display the cropping frame (scan area) according to the item size. You can also manually specify the scan area in thumbnail view or when there are white margins along the item (for example, in photos), or when you want to create custom cropping frames.
Cannot Scan at the Correct Size Check: Make sure that the items are placed correctly.
Item Is Placed Correctly, but the Scanned Image Is Slanted Check: When Document or Magazine is selected for the item type, deselect the Correct slanted text document checkbox and scan the item again.
Scanned Image Is Enlarged (Reduced) on the Computer Monitor Check 1: Change the display setting in the application. Refer to the application's manual for details. If you have any questions, contact the manufacturer of the application. Note You cannot reduce the image size in Paint. To reduce the display size, open the images in an application. Check 2: Change the resolution setting in ScanGear (scanner driver) and scan again. The higher the resolution, the larger the resulting image will be.
Software Problems The E-mail Client You Want to Use Does Not Appear in the Screen for Selecting an Email Client 78
The E-mail Client You Want to Use Does Not Appear in the Screen for Selecting an E-mail Client Check: Check that the e-mail client's MAPI is enabled. Refer to the e-mail client's manual for how to set MAPI. If the problem is not solved even when MAPI is enabled, select None (Attach Manually) in the screen for selecting an e-mail client, then manually attach the image to the outgoing email.
Problems with the Machine The Machine Cannot Be Powered On The Machine Turns Off Unintendedly Cannot Connect to Computer with a USB Cable Properly Cannot Communicate with the Machine with USB Connection Printer Status Monitor Is Not Displayed 80
The Machine Cannot Be Powered On Check1 Press the ON button. Make sure that the power plug is securely plugged into the power cord connector of the machine, then turn it back on. Check2 Unplug the machine from the power supply, then plug the machine back in and turn the machine back on after leaving it for at least 2 minutes. Check3 If the problem is not resolved, contact the service center.
The Machine Turns Off Unintendedly Check Deactivate the setting to turn the unit off automatically. The machine turns off automatically according to the elapsed time you specified if you activate the setting to turn the unit off automatically. If you do not want the machine to turn off automatically, open the printer driver setup window and in Auto Power under the Maintenance sheet, select Disable for Auto Power Off.
Cannot Connect to Computer with a USB Cable Properly Printing or Scanning Speed Is Slow/Hi-Speed USB Connection Does Not Work/"This device can perform faster" Message Is Displayed If your system environment is not fully compatible with Hi-Speed USB, the machine will operate at a lower speed provided under USB 1.1. In this case, the machine operates properly but printing or scanning speed may slow down due to communication speed.
Cannot Communicate with the Machine with USB Connection Check1 Make sure that the machine is turned on. Check2 Make sure that the USB cable is connected properly. See Connecting the Machine to the Computer Using a USB Cable to connect the USB cable properly. Check3 Do not start up IJ Network Tool while printing. Check4 Do not print while IJ Network Tool is running. Make sure that Enable bidirectional support is selected in the Ports sheet of the properties dialog box of the printer driver.
Printer Status Monitor Is Not Displayed Check Is the printer status monitor enabled? Make sure that Enable Status Monitor is selected on the Option menu of the printer status monitor. 1. Open the printer driver setup window. How to Open the Printer Driver Setup Window 2. On the Maintenance sheet, click View Printer Status. 3. Select Enable Status Monitor on the Option menu if it is not selected.
Problems with Installation/Downloading Cannot Install the MP Drivers Easy-WebPrint EX Does Not Start Up or Easy-WebPrint EX Menu Does Not Appear How to Update MP Drivers in Network Environment Uninstalling IJ Network Tool 86
Cannot Install the MP Drivers • If the installation does not start even after the Setup CD-ROM is inserted into your computer's disc drive: Start the installation following the procedure below. 1. Select items as shown below. ◦ In Windows 8, select the Explorer icon in Taskbar on Desktop, then select Computer from the list on the left. ◦ In Windows 7 or Windows Vista, click Start then Computer. ◦ In Windows XP, click Start then My Computer. 2. Double-click the CD-ROM icon on the displayed window.
Note • The printer is not detected. Check the connection. may be displayed depending on the computer you use. Check1 Make sure that the USB cable is securely plugged in to the machine and the computer. Check2 Follow the procedure below to connect the machine and the computer again. 1. Turn the machine off. 2. Unplug the USB cable from the machine and the computer, then connect it again. 3. Turn the machine on.
Easy-WebPrint EX Does Not Start Up or Easy-WebPrint EX Menu Does Not Appear If Easy-WebPrint EX does not start up or its menu does not appear on Internet Explorer, confirm the following. Is Canon Easy-WebPrint EX displayed on the Toolbars menu in the Internet Explorer's View menu? Check1 If Canon Easy-WebPrint EX is not displayed, Easy-WebPrint EX is not installed on your computer. Install the latest Easy-WebPrint EX onto your computer from our website.
How to Update MP Drivers in Network Environment Download the latest MP Drivers in advance. To obtain the latest MP Drivers, access our web site through the Internet and download the latest MP Drivers for your model. After uninstalling the MP Drivers, install the latest MP Drivers according to the regular procedure. When the connection method selection screen is displayed, select Use the printer with wireless LAN connection. The machine will be detected automatically in the network.
Uninstalling IJ Network Tool Follow the procedure below to uninstall IJ Network Tool from your computer. Important • Even if IJ Network Tool is uninstalled, you can print and scan from the computer over network. However, you cannot change the network settings over network. • Log into a user account with administrator privilege. 1. Perform the procedure to uninstall IJ Network Tool. • In Windows 8: 1. Select Control Panel from the Settings charm on Desktop > Programs > Programs and Features. 2.
About Errors/Messages Displayed If an Error Occurs A Message Is Displayed 92
If an Error Occurs When an error occurs in printing such as the machine is out of paper or paper is jammed, a troubleshooting message is displayed automatically. Take the appropriate action described in the message. When an error occurs, the Alarm lamp flashes orange and a Support Code (error number) is displayed on the computer screen. For some errors, the ON lamp and the Alarm lamp flashes alternately. Check the status of the lamps and the message, then take the appropriate action to resolve the error.
10 flashes Loaded paper is not compatible with automatic duplex printing. 1310 11 flashes Cannot perform automatic duplex printing with the current paper size setting. 4103 12 flashes You cannot print the contents on CREATIVE PARK PREMIUM. 4100 13 flashes The ink may have run out. 1686 14 flashes The ink cartridge cannot be recognized. 1684 15 flashes The FINE cartridge cannot be recognized. 1682 16 flashes The ink has run out. 1688 21 flashes The machine cannot detect the paper size.
• When a Support Code and a message are displayed on the computer screen: Note • You can confirm the actions against errors with Support Codes on your computer by searching a Support Code. Click Here to Search For details on how to resolve errors without Support Codes, see A Message Is Displayed.
A Message Is Displayed This section describes some of the errors or messages. Note • A Support Code (error number) is displayed on the computer for some error or message. For details on errors with Support Codes, refer to Support Code List.
• In Windows 8 or Windows 7, right-click the "Canon XXX Printer" icon (where "XXX" is your machine's name), then select Printer properties. • In Windows Vista or Windows XP, right-click the "Canon XXX Printer" icon (where "XXX" is your machine's name), then select Properties. 4. Click the Ports tab to confirm the port settings. Make sure that a port named "USBnnn" (where "n" is a number) with "Canon XXX Printer" appearing in the Printer column is selected for Print to the following port(s).
Follow the procedure below to check the status of the device. 1. Open the Device Manager on your computer as shown below. If the User Account Control screen is displayed, follow the on-screen instructions. • In Windows 8, select Control Panel from the Settings charm on Desktop > Hardware and Sound > Device Manager. • In Windows 7 or Windows Vista, click Control Panel, Hardware and Sound, then Device Manager.
• If you agree to participate in the survey program: Click Agree, then follow the on-screen instructions. The printer usage information will be sent via the Internet. If you have followed the on-screen instructions, the information will be sent automatically from the second time onward and the confirmation screen will not be displayed again. Note • When the information is being sent, a caution screen such as an Internet security screen may be displayed.
Note • In Windows 8, Windows 7 or Windows Vista, a confirmation/warning dialog box may appear when installing, uninstalling or starting up software. This dialog box appears when administrative rights are required to perform a task. If you are logged on to an administrator account, follow the on-screen instructions. 2. Select Canon Inkjet Printer/Scanner/Fax Extended Survey Program. 3. Select Change.
If You Cannot Resolve the Problem If you cannot resolve the problem with any of the workarounds in this chapter, please contact the seller of the machine or the service center. Canon support staff are trained to be able to provide technical support to satisfy customers. Caution • If the machine emits any unusual sound, smoke, or odor, turn it off immediately. Unplug the power cord from the outlet and contact the seller or the service center. Never attempt to repair or disassemble the machine yourself.
Support Code List (MG3510, MG3520, MG3540, MG3550, MG3560, MG3570, MG3580) The support code appears on the computer screen when an error occurs. "Support Code" means the error number and appears with an error message. When an error occurs, check the support code displayed on the computer screen and take the appropriate action.
• A000 to ZZZZ B200 About the support code for paper jam, you can also refer to Support Code List (When Paper Is Jammed).
Support Code List (When Paper Is Jammed) If the paper is jammed, remove it following the procedure appropriate for each case.
1300 Cause Paper is jammed in the paper output slot. Action If you can see the jammed paper at the paper output slot, remove the paper following the procedure below. Note • If you need to turn off the machine to remove jammed paper during printing, press the Stop button to cancel print jobs before turning off the machine. 1. Pull the paper out slowly. Hold the paper with your hands, then pull the paper out slowly not to tear it.
Note • When reloading the paper, confirm that you are using the paper suited for printing and are loading it correctly. • We recommend you use paper other than A5 sized one to print documents with photos or graphics; otherwise, the printout may curl and cause paper exit jams. If you cannot remove the paper or the paper tears inside the machine, or if the paper jam error continues after removing the paper, contact the service center.
1303 Cause Paper is jammed inside the machine at the transport unit. Action If you can see the jammed paper at the front tray, or you cannot see the paper either at the paper output slot or at the front tray, remove the paper from the transport unit. Remove the paper following the procedure below. Note • If you need to turn off the machine to remove jammed paper during printing, press the Stop button to cancel print jobs before turning off the machine. 1. Turn the machine off, then unplug the power cord.
5. Pull out the jammed paper slowly. When you pull the jammed paper, support the machine with your hand so that it does not fall down. Note • If the paper is rolled up and it is difficult to remove, grasp the edges of the paper, then remove the jammed paper. • If you cannot remove the jammed paper from the transport unit, close the transport unit, take back the machine in original position, then open the paper output cover to remove the paper. Paper Is Jammed inside the Machine 6.
7. Plug the machine back in and turn the machine back on. 8. Reload the paper. All print jobs in the queue are canceled. Reprint if necessary. If you cannot remove the paper or the paper tears inside the machine, or if the paper jam error continues after removing the paper, contact the service center.
1304 Cause Paper is jammed when performing automatic duplex printing. Action If the paper is jammed when performing automatic duplex printing, remove the paper following the procedure below. Note • If you need to turn off the machine to remove jammed paper during printing, press the Stop button to cancel print jobs before turning off the machine. 1. Pull the paper out slowly from the paper output slot. Hold the paper with your hands, then pull the paper out slowly not to tear it.
6. Push the open lever to open the transport unit. When you open the transport unit, support the machine with your hand so that it does not fall down. 7. Pull out the jammed paper slowly. When you pull the jammed paper, support the machine with your hand so that it does not fall down. Note • If the paper is rolled up and it is difficult to remove, grasp the edges of the paper, then remove the jammed paper.
Note • After you close the transport unit, take back the machine in original position at once. 9. Plug the machine back in and turn the machine back on. 10. Reload the paper. All print jobs in the queue are canceled. Reprint if necessary. If you cannot remove the paper or the paper tears inside the machine, or if the paper jam error continues after removing the paper, contact the service center.
Paper Is Jammed inside the Machine If the jammed paper tears and you cannot remove the paper either from the paper output slot or from the transport unit, or if the jammed paper remains inside the machine, remove the paper following the procedure below. Note • If you need to turn off the machine to remove jammed paper during printing, press the Stop button to cancel print jobs before turning off the machine. 1. Turn off the machine, and unplug the power cord of the machine from the power supply. 2.
4. Hold the jammed paper with your hands. If the paper is rolled up, pull it out. 5. Pull the paper slowly not to tear it, then pull the paper out. 6. Make sure that all the jammed paper is removed.
If the paper is torn, a piece of paper may remain inside the machine. Check the following and remove the piece of paper if it remains. • Does the piece of paper remain under the FINE cartridge holder? • Does the little piece of paper remain inside the machine? • Does the piece of paper remain in the right side or the left side space (B) inside the machine? 7. Close the paper output cover, then reload the paper. All print jobs in the queue are canceled. Reprint if necessary.
In Other Cases Make sure of the following: Check1 Are there any foreign objects around the paper output slot? Check2 Is the paper curled? Load the paper after correcting its curl.
1003 Cause The machine is out of paper, or paper does not feed. Action Reload the paper and press the machine's Black or Color button. When you load the paper, insert the paper stack until the leading edge touches the far end of the front tray.
1200 Cause The paper output cover is open. Action Close the paper output cover and wait for a while. Do not close it while you are replacing a FINE cartridge.
1202 Cause The paper output cover is open. Action Close the paper output cover.
1250 Cause The paper output tray is closed. Action Open the paper output tray to resume printing.
1310 Cause The size of paper may not be compatible with automatic duplex printing. Action The sizes of media suitable for auto duplex printing are A4 and Letter. Make sure that the size of the paper loaded in the machine is correct. Pressing the Black or Color button will eject the paper and restart printing from the front side of the next paper. The reverse side of the ejected sheet will not be printed.
1401 Cause The FINE cartridge is not installed. Action Install the FINE cartridge. If the error is not resolved, the FINE cartridge may be damaged. Contact the service center.
1403 Cause Appropriate FINE cartridge is not installed. Action Install the appropriate FINE cartridge. If the error is not resolved, the FINE cartridge may be damaged. Contact the service center.
1485 Cause Appropriate ink cartridge is not installed. Action Printing cannot be executed because the ink cartridge is not compatible with this machine. Install the appropriate ink cartridge. If you want to cancel printing, press the machine's Stop button.
1486 Cause The FINE cartridge is not installed in the correct position. Action Make sure that each FINE cartridge is installed in the correct position.
1487 Cause The FINE cartridge is not installed in the correct position. Action Make sure that each FINE cartridge is installed in the correct position.
1682 Cause The FINE cartridge cannot be recognized. Action Replace the FINE cartridge. If the error is not resolved, the FINE cartridge may be damaged. Contact the service center.
1684 Cause The ink cartridge cannot be recognized. Action Printing cannot be executed because the ink cartridge may not be installed properly or may not be compatible with this machine. Install the appropriate ink cartridge. If you want to cancel printing, press the machine's Stop button.
1686 Cause The ink may have run out. Action The function for detecting the remaining ink level will be disabled since the ink level cannot be correctly detected. If you want to continue printing without this function, press the machine's Stop button for at least 5 seconds. Canon recommends to use new genuine Canon cartridges in order to obtain optimum qualities. Please be advised that Canon shall not be liable for any malfunction or trouble caused by continuation of printing under the ink out condition.
1687 Cause The FINE cartridge is not installed properly. Action Open the paper output cover. When the head cover opens, push up the ink cartridge lock lever to confirm that the FINE cartridges are installed properly. After that, close the paper output cover. If the error is not resolved, remove the FINE cartridges, then install them again.
1688 Cause The ink has run out. Action Replace the ink cartridge and close the paper output cover. If printing is in progress and you want to continue printing, press the machine's Stop button for at least 5 seconds with the ink cartridge installed. Then printing can continue under the ink out condition. The function for detecting the remaining ink level will be disabled. Replace the empty ink cartridge immediately after the printing.
1702 Cause The ink absorber is almost full. Action Press the machine's Black or Color button to continue printing. Contact the service center.
1703 Cause The ink absorber is almost full. Action Press the machine's Black or Color button to continue printing. Contact the service center.
1704 Cause The ink absorber is almost full. Action Press the machine's Black or Color button to continue printing. Contact the service center.
1705 Cause The ink absorber is almost full. Action Press the machine's Black or Color button to continue printing. Contact the service center.
1712 Cause The ink absorber is almost full. Action Press the machine's Black or Color button to continue printing. Contact the service center.
1713 Cause The ink absorber is almost full. Action Press the machine's Black or Color button to continue printing. Contact the service center.
1714 Cause The ink absorber is almost full. Action Press the machine's Black or Color button to continue printing. Contact the service center.
1715 Cause The ink absorber is almost full. Action Press the machine's Black or Color button to continue printing. Contact the service center.
1890 Cause The protective material for the FINE cartridge holder or the tape may remain attached to the holder. Action Open the paper output cover, then confirm that the protective material or the tape does not remain attached to the FINE cartridge holder. If you find the protective material or the tape remains attached, remove it, then close the paper output cover. If the problem is not resolved, contact the service center.
2100 Cause The paper size in the print settings and the size of the loaded paper do not match. Action Check the print settings and the loaded paper, load paper of the correct size, then press the machine's Black or Color button. If you want to cancel printing, press the machine's Stop button.
2101 Cause The paper size in the print settings and the size of the loaded paper do not match. Action Check the print settings and the loaded paper, load paper of the correct size, then press the machine's Black or Color button. If you want to cancel printing, press the machine's Stop button.
2102 Cause The machine has detected that the paper has been fed aligned to one side. Action Load the paper into the center of the front tray, then slide the paper guides to align with the both edges of the paper stack. Press the machine's Black or Color button to dismiss the error.
2103 Cause The machine cannot detect the paper size. Action Press the machine's Stop button to dismiss the error, then try to print again. If this error still occurs even after printing again, set the machine not to detect the paper width by using the operation panel, the printer driver, or Remote UI. Note • Depending on the type of paper, the machine may not detect the paper width. Additionally, if the paper output cover is opened while printing is in progress, the machine may not detect the paper width.
2900 Cause Scanning the print head alignment sheet has failed. Action Press the machine's Black or Color button to dismiss the error. Check the following points, perform Automatic Print Head Alignment again. • Make sure that the print head alignment sheet is set in the correct position and orientation on the platen glass. • Make sure the platen glass and the print head alignment sheet are not dirty. • Make sure the type and size of loaded paper is suitable for Automatic Print Head Alignment.
2901 Cause Printing of the print head alignment pattern is complete and the machine is in waiting for scanning the sheet. Action Proceed to scan the printed alignment pattern. 1. Load the print head alignment sheet on the platen glass. Load the print head alignment sheet with the printed side facing down and align the mark upper left corner of the sheet with the alignment mark on the . 2. Close the document cover gently, then press the machine's Black or Color button.
4100 Cause The specified data cannot be printed. Action When you print the contents on CREATIVE PARK PREMIUM, confirm the message on the computer screen, make sure that genuine Canon FINE cartridges are all installed properly, then start printing again.
4103 Cause Cannot perform automatic duplex printing with the current paper size setting. Action Press the machine's Stop button, to cancel printing. Then, change the paper size setting and print again.
5011 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
5012 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
5100 Cause Printer error has occurred. Action Cancel printing, turn off the machine. Then clear the jammed paper or protective material that is preventing the FINE cartridge holder from moving, and turn on the machine again. If the problem is not resolved, contact the service center. Important • When you clear the jammed paper or protective material that is preventing the FINE cartridge holder from moving, be careful not to touch the components inside the machine.
5200 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
5400 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
5B02 Cause Printer error has occurred. Action Contact the service center.
5B03 Cause Printer error has occurred. Action Contact the service center.
5B04 Cause Printer error has occurred. Action Contact the service center.
5B05 Cause Printer error has occurred. Action Contact the service center.
5B12 Cause Printer error has occurred. Action Contact the service center.
5B13 Cause Printer error has occurred. Action Contact the service center.
5B14 Cause Printer error has occurred. Action Contact the service center.
5B15 Cause Printer error has occurred. Action Contact the service center.
6000 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6500 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6800 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6801 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6900 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6901 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6902 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6910 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6911 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6930 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6931 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6932 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6933 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6936 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6937 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6938 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6940 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6941 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6942 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6943 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6944 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6945 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
6946 Cause Printer error has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Plug the machine back in and turn the machine back on. If the problem is not resolved, contact the service center.
B200 Cause An error requiring you to contact the service center has occurred. Action Turn off the machine, and unplug the power cord of the machine from the power supply. Contact the service center.
