<< Previous Next >> Installing Your Multifunction to Your Network for the First Time PIXMA MP990 / PIXMA MP640 / PIXMA MP560 Windows OS 1
<< Previous Next >> Installing Your Multifunction to Your Network for the First Time PIXMA MP990 / PIXMA MP640 / PIXMA MP560 Windows OS Preparing to Connect My Multifunction to My Network Network Requirements Important Information You Need Before Adding Your Multifunction Adding Your Multifunction to the Network Confirm Connection Status Downloading & Installing the Drivers Downloading the Driver Installing the Driver 3 3 4 5 9 12 12 15 2
Preparing to Connect My Multifunction To My Network << Previous Next >> Network Requirements Before connecting the machine to the network, make sure that configuration of the computer and access point or router is complete, and that the computer is connected to the network. Notes on Network Connection • The configuration, router functions, setup procedures and security settings of the network device vary depending on your system environment.
Preparing to Connect My Multifunction To My Network << Previous Next >> An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without using an access point, is not supported. Be sure to prepare an access point. Important Information You Need Before Adding Your Multifunction The following information is required to connect to your access point or router. • Access Point Name/Network Name: Also referred to as SSID.
Adding Your Multifunction to Your Network << Previous Next >> Adding Your Multifunction to Your Network Step One Step Two Use the Easy-Scroll Wheel* (A) to select Settings, and then press the OK button. Select Device settings, then press the OK button. *Easy-Scroll Wheel location varies according to model. MP640 pictured in examples below.
Adding Your Multifunction to Your Network << Previous Step Three Step Four Select Yes, then press the OK button. Select Change wireless / wired, then press the OK button. Next >> When wireless connection is enabled, the Wi-Fi lamp** (B) lights blue. **Wi-Fi lamp location varies according to model.
Adding Your Multifunction to Your Network << Previous Next >> Step Five Step SIx Select the access point name you wrote down, then press the OK button. When one of the following screens is displayed, enter the network key you wrote down, then press the OK button. If the following screen is not displayed, go to Step Eight. Use the Easy-Scroll Wheel to select the character. Use the to move the cursor to the right. NOTE: If you are living in an apartment, nearby access points in use may be detected.
Adding Your Multifunction to Your Network << Previous Next >> Step Seven Step Eight Make sure that the network key is correct, and then press the OK button. When the completion screen appears, press the OK button, then press the HOME*** button (C). ***HOME button location varies depending on model. The standby screen returns. NOTE: If Failed to connect to the access point. appears, press the OK button, make sure that the network key is correct, then enter it again.
Adding Your Multifunction to Your Network << Previous Next >> Confirm Connection Status Step One Step Two Press the HOME*** button (A), select Settings using the Easy-Scroll Wheel (B), and then press the OK button. Select Device settings, and then press the OK button. ***HOME button location varies depending on model. IMPORTANT: Confirm connection status after installing the machine in the target location.
Adding Your Multifunction to Your Network << Previous Step Three Step Four Select LAN settings, and then press the OK button. Select Confirm LAN settings, then press the OK button.
Adding Your Multifunction to Your Network << Previous Next >> Step Five Select Wireless LAN setting list, then press the OK button. Make sure that Connection is set to Active, and then press the HOME button. It may take a while before the connection is complete. In this case, press the Back* button (C) and wait for about a minute, then display the Wireless LAN setting list screen again. *Back button location varies depending on model.
Downloading and Installing the Drivers << Previous Next >> Downloading the Driver To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of applications to be installed.
Downloading and Installing the Drivers << Previous Next >> Step Three In the Drivers section, click the Download icon *Name varies by model for the MP Driver example: MP990 * The file name turns red when the mouse pointer is on the file name 13
Downloading and Installing the Drivers << Previous Next >> Step Four On the next screen, read the information and instructions and click I Agree - Begin Download Select [Save] or [Run]. If [Run] is selected, the file will be automatically installed If [Save] is selected, once the file has been downloaded, double-click it to begin the installation process IMPORTANT: • Quit all running applications before installation. • Log on as the administrator (or a member of the Administrators group).
Downloading and Installing the Drivers << Previous Next >> Installing the Driver NOTE: If a User Account Control screen appears, click Continue or Yes (depending on Windows version) to continue. NOTE: If the same screen reappears in subsequent steps, click Continue or Yes. Step One Step Two Click Next on the Welcome screen. Select your place of residence and click Next.
Downloading and Installing the Drivers Step Three Step Four Click Yes for the License Agreement.
Downloading and Installing the Drivers << Previous Next >> Step Four Step Five Select Use the Printer on network on the Connection method screen, and then click Next. After searching for printers, the Detected Printers List appears. Verify your printer is detected and click Next.
Downloading and Installing the Drivers << Previous Next >> Step Six Step Seven Setup will install the driver components. After completion, click Next on the Setup Completion screen. When the Connection Performance Measurement dialog box appears, click Next.
Downloading and Installing the Drivers << Previous Next >> Step Eight Confirm the measurement results, and then click Finish. Ensure that Access Point. If the following window appears, click OK to restart or Cancel to restart later is displayed in Connection Performance between the Printer and the • If an icon other than appears, improve the communication status by referring to the displayed message or the help file, then click Remeasurement.
