DIE-0415-000 Wireless File Transmitter WFT-E6 Y P O Guide for Canon Camcorders C E
Introduction About this Guide You can attach a WFT-E6 Wireless File Transmitter to a Canon camcorder to connect the camcorder to a Wi-Fi network. This will allow you to operate the camcorder remotely from any device connected to the Wi-Fi network using Wi-Fi Remote, a Web browser application. This guide will explain how to attach the WFT-E6 to a camcorder and configure the transmitter for use with a camcorder.
Contents Introduction 2 About this Guide ................................................................................................................................ 2 Attaching to a Camcorder .................................................................................................................. 4 1 Wi-Fi and Camcorder Settings 7 Three Ways to Connect to a Wi-Fi Network.......................................................................................
Attaching to a Camcorder Turn off the camcorder before attaching the WFT-E6 Wireless File Transmitter. The transmitter is powered by the camcorder. Make sure the camcorder’s battery pack is sufficiently charged before using the transmitter. 1 2 Turn off the camcorder. Open the WFT terminal cover. Y 3 OP C Attach the transmitter. Align the transmitter’s terminal to the camcorder’s WFT terminal as shown in the illustration and firmly push it in ( ).
Attaching to a Camcorder 5 Turn on the camcorder. If the transmitter was correctly attached, the icon will appear in the rear panel, next to the remaining battery icon. Removal Turn off the camcorder. Loosen the WFT attachment bracket’s screw and remove the WFT attachment bracket. Loosen the transmitter’s tightening screw until it spins freely. Remove the transmitter’s terminal from the camcorder’s WFT terminal and close the WFT terminal’s cover.
C Y P O
1 Wi-Fi and Camcorder Settings Y P O Complete the Wi-Fi and camcorder settings using the camcorder’s menu screens.
Three Ways to Connect to a Wi-Fi Network Before using the Wi-Fi Remote application to remotely control the camcorder, you need to wirelessly connect the camcorder (with the transmitter attached) to a Wi-Fi network via an access point (wireless router). There are three ways to do so, and the method you use will depend on the specifications of the access point you want to use. Note that using an unprotected Wi-Fi network can expose your data to monitoring by unauthorized third parties.
Wi-Fi Protected Setup (WPS) - Button Wi-Fi Protected Setup (WPS) is the easiest way to set up the Wi-Fi network. However, it may not work correctly if there are several active access points in the area. In such case try using the [WPS: Pin Code] (A 10) or [Connection Wizard] (A 11) option. 1 2 Open the [Set Up New] submenu. [w Other Functions] > [Wi-Fi Remote] > [Set Up New] Select [WPS: Button] and then press SET. 3 Press the WPS button on the wireless router.
Wi-Fi Protected Setup (WPS) - PIN Code In this setup mode, the camcorder will issue an 8-digit PIN code that you then need to enter in the wireless router setup screen. Even if there are multiple access points active in your area, this is a relatively reliable method of establishing a connection using a shared PIN code. It may take about one minute to establish connection. 1 2 3 Open the [Set Up New] submenu. [w Other Functions] > [Wi-Fi Remote] > [Set Up New] Select [WPS: PIN Code] and then press SET.
Connection Wizard Selecting the Wi-Fi Network When you select [Connection Wizard], the transmitter will detect active Wi-Fi networks in your area and you can select the desired access point (SSID) from the list. 1 2 3 Open the [Set Up New] submenu. [w Other Functions] > [Wi-Fi Remote] > [Set Up New] Select [Connection Wizard] and then press SET. Select [Automatic] and then press SET. The camcorder will search for active access points in your area and display a list of available options.
Connection Wizard Encrypted Access Points If the access point is encrypted (C), you will need to enter the encryption key (password). To find out the encryption key, refer to the instruction manual of the access point (wireless router) or consult the network administrator. 1 [WEP]/[Shared Key] Select the WEP index key. This step is only necessary if the Wi-Fi network’s authentication method is set to [Shared Key] or if the encryption method is set to [WEP].
Connection Wizard Entering the Wi-Fi Network’s Details Manually If you prefer, you can enter manually the details of the Wi-Fi network you want to connect to (for example, if your Wi-Fi network is operating in stealth mode and cannot be detected by the transmitter or to connect to a Wi-Fi-enabled portable device through an Ad Hoc connection). After step 2 in the Selecting the Wi-Fi Network procedure (A 11): 1 2 Select [Manual] and then press SET. Select the wireless connection mode and then press SET.
Connection Wizard Ad Hoc Connections 4 5 Select the channel and then press SET. Available channels will be different for Ad Hoc 11b/g and 11a connections. Select the Ad Hoc connection’s encryption method and then press SET. If you selected [WEP], continue with step 6 below. If you selected [No encryption], skip to step 7. Infrastructure Connections 4 Select the Wi-Fi network’s authentication method and then press SET. Y P O If you selected [Shared Key], skip to step 6.
Configuring Network (TCP/IP) Settings 1 Select [Automatic] or [Manual] and then press SET. 2 Enter the network’s TCP/IP settings manually. If you selected [Automatic], IP settings will be assigned automatically. Continue with the procedure to review and save the configuration (A 16). C Enter the IP address assigned to the camcorder, and the network’s subnet mask, and default gateway.
Saving the Configuration 1 2 Review the access point’s configuration and then press SET. The first screen shows the access point’s SSID and the type of connection. Push the joystick up/ down or turn the SELECT dial to review additional settings before pressing SET. Save the current configuration. C 16 Select the desired configuration number and then press SET. You can save up to 5 different network configuration profiles on the camcorder.
Camcorder Settings A user name and password are required before the Wi-Fi Remote application (Wi-Fi-enabled device connected to the Wi-Fi network) can access the transmitter in order to operate the camcorder. Additionally, you can set a unique camcorder identification code and designate the port that Wi-Fi Remote should use. The Wi-Fi connection will be disabled while you change these settings. [User Name]*, [Password]* Protect the remote operation of the camcorder with a user name and password. [Port No.
C Y P O
2 Remote Operation Using Wi-Fi Remote Y P O After completing the preparations in the previous chapter, you can use any computer or other Wi-Fi enabled device that has a Web browser and is connected to the same Wi-Fi network to remotely operate the camcorder using the Wi-Fi Remote application.
Selecting a Configuration Number You can save up to 5 different network configuration profiles. You can select which one to use depending on where you plan to use the camcorder. If you just saved a new network configuration (A 16), the camcorder will automatically connect to that Wi-Fi network and this procedure is not required. 1 2 Open the Wi-Fi [Select] submenu. [w Other Functions] > [Wi-Fi Remote] > [Select] Select the desired configuration number and then press SET.
Starting Wi-Fi Remote After establishing a connection between the camcorder and Wi-Fi network (the white icon appears on the upper left of the screen), you can start the Wi-Fi Remote application on any Wi-Fi-enabled device* that has a Web browser** and is connected to the same Wi-Fi network. Refer also to the instruction manual of the Wi-Fi enabled device used. * For details about compatible devices, operating systems, Web browsers, etc. please visit your local Canon Web site.
Starting Wi-Fi Remote Starting Wi-Fi Remote 1 2 Start the Web browser on the computer or other Wi-Fi-enabled device. Enter the camcorder’s URL. Enter the IP address you checked previously into the Web browser’s address bar, adding the prefix “http://”. Camcorder’s IP address from the Status screen 3 Enter the user name and password and press [OK]. Example of the login screen. The screen may differ depending on the Web browser and version used.
Starting Wi-Fi Remote 4 Select the language for Wi-Fi Remote. C Press the [Î] next to the language button and select the desired language from the list. Most buttons and controls emulate physical controls on the camcorder and are labeled in English only, regardless of the language selected.
Wi-Fi Remote: [Advanced Control] When using a laptop computer, netbook, tablet computer or other Wi-Fi-enabled devices with larger screens, the [Advanced Control] screen offers more shooting controls to operate the camcorder. For details about how to control the recording or change the various settings, refer to the relevant section in the camcorder’s instruction manual.
Wi-Fi Remote: [Basic Control] When using a smartphone or other Wi-Fi-enabled device with a smaller screen, you can use the [Basic Control] screen that offers only the most important shooting controls but will fit in the screen without scrolling. For details about how to control the recording or change the various settings, refer to the relevant section in the camcorder’s instruction manual. 1 Open the [Basic Control] screen. From the [Advanced Control] screen press the [Basic Control] tab.
Wi-Fi Remote: [Metadata Input] Using Wi-Fi Remote you can create, edit and transfer to the camcorder a metadata profile that includes the User Memo information (clip title, creator, location and description), as well as GPS information. For details about how to set and transfer the metadata, refer to the relevant section in the camcorder’s instruction manual. 1 Open the [Metadata Input] screen. From the [Advanced Control] screen press the [Metadata Input] tab.
3 Managing Settings Information C Y P O 27
Checking Settings You can check the current Wi-Fi network settings using the camcorder’s status screens. 1 2 Press the STATUS button. Push the joystick up/down or turn the SELECT dial to display the four [Wi-Fi Remote] status screens.
Changing Settings You can edit the Wi-Fi network settings even after the initial setup. Changing settings manually requires more advanced knowledge of Wi-Fi and network settings. The Wi-Fi connection will be disabled while you change these settings. After completing the changes, the camcorder will connect to the Wi-Fi network using the new configuration. 1 2 3 Select the network configuration profile you want to change (A 20). Open the Wi-Fi [Edit] submenu.
Changing Settings 7 If you selected [Manual], select a setting you want to change and then press SET. Push the joystick up/down or turn the SELECT dial to select a value for the first field and press SET to move to the next field. After completing the four fields of each address, select [Set] and press SET to enter the address. Repeat this step to change other TCP/IP settings as necessary. When you finish changing the settings, select [L], press SET and then close the menu.
4 Troubleshooting C Y P O 31
Troubleshooting Check this section if you encounter problems connecting to the Wi-Fi network or operating the camcorder remotely from a Wi-Fi-enabled device. If the problem persists, consult a Canon Service Center (listed on the back cover of the camcorder’s instruction manual).
About Wi-Fi Networks When using the transmitter with a Wi-Fi network, try the following corrective actions if the transmission rate drops, the connection is lost, or other problems occur. Location and Antenna Position of the Wireless Router or Wi-Fi-Enabled Device When using the transmitter indoors, place the wireless router in the same room where you are shooting. Place the wireless router in an open, unobstructed location, where people or objects do not come between it and the camcorder.
Error Messages Refer to this list when an error message is displayed on the camcorder’s screen. Messages are listed alphabetically. If the problem persists, consult a Canon Service Center (listed on the back of the camcorder’s instruction manual). Another user is already accessing the camcorder. Try again later. The camcorder is already connected to another instance of Wi-Fi Remote on another Web browser. X The camcorder can only be controlled from one Wi-Fi Remote instance.
Error Messages Wi-Fi connection terminated An error occurred on the access point or the computer or other Wi-Fi-enabled device. X Check the Wi-Fi-enabled device and access point and try connecting again. The Wi-Fi signal became too weak and the wireless connection was lost. X Wait a moment or turn off other devices in the area that may be interfering with the Wi-Fi signal and then try connecting again. Wi-Fi error. Incorrect encryption key.
Index A N Access point .......................................... 2, 11 Ad Hoc....................................................... 13 Advanced Control screen .......................... 24 Area of use .... Areas of Use and Restrictions Attaching to a camcorder ............................ 4 Authentication............................................ 14 B Basic Control screen ................................. 25 Button connection mode.............................. 9 C E Settings information ..........
C Y P O Windows is a trademark or registered trademark of Microsoft Corporation in the United States and other countries. Wi-Fi is a registered trademark of the Wi-Fi Alliance. Wi-Fi Certified, WPA, WPA2, and the Wi-Fi Certified logo are trademarks of the Wi-Fi Alliance. WPS as used on the camcorder’s settings, onscreen displays and in this manual signifies Wi-Fi Protected Setup.
C Y P O The information in this guide is current as of December 2011. For information on using the transmitter with accessories introduced after this date, contact your nearest Canon Service Center. DIE-0415-000 © CANON INC.
