Service manual

GV 30…, GV 50… Allgemeiner Teil / General Section
GRUNDIG Service 1 - 25
CONNECTION AND PREPARATION
_______________________________________
14
4 Connect the »DECODER/ Y EURO-AV2« socket on the video recorder
to the »VCR« socket on the VCR-SAT module with a standard Scart cable.
5 Connect the »
ʐ
« socket on the video recorder to the »SAT-LINK« socket
(control line) on the VCR-SAT module with a standard Scart cable.
6 Plug the satellite antenna cable into the corresponding antenna socket
(INPUT-SAT) on the VCR-SAT module.
Note:
The socket »LINE 2 (II) IN/DECODER« can also be used for connecting a
PAY-TV decoder.
If a VCR-SAT module is installed in this socket, connect the PAY-TV decoder to
the »DEC« socket of the VCR-SAT module.
In this case, the decoder can only be used for television stations supplied by
the VCR-SAT module.
7 Plug the mains cable supplied into the »AC IN ~ « socket on the video
recorder, and plug it into the mains wall socket.
– The video recorder is now in standby mode.
8 Connect the VCR-SAT module to the mains supply.
Caution:
The only way to isolate the video recorder and the VCR-SAT module from the
mains is to pull the plug.
7
12
TV
DECODER/
EURO-AV2
EURO-AV1
AUDIO
OUT
L
R
TV
DECODER/
EURO-AV2
EURO-AV1
AUDIO
OUT
L
R
AC IN
2
3
0
V
5
0
-6
0
H
z
IN
P
U
T
S
A
T
VCR
DEC
9
5
0
-
2
1
5
0
M
H
z
1
4
/
1
8
V
0
,
3
5
A
m
a
x
.
D
O
N
O
T
R
E
M
O
V
E
C
O
V
E
R
S
H
A
Z
A
R
D
L
I
V
E
-
P
A
R
T
S
SAT-LINK
18
TUNING
_________________________________________________________________________________
Tuning the video recorder and the television
You do not need to do this if the video recorder and the television are connected
via a EURO-AV (Scart) cable.
1
Switch on the television.
2
Select the »AV« channel position on the television set for recorder playback
via the antenna cable.
3
Tune the television to a free channel in the UHF band between channel 21
and channel 69. A free channel is one which does not carry a signal from a
television station (you can only see and hear static).
– Many televisions display the channel number.
4
Store the free channel position on the television.
5
Press »
Ǽ
« to switch the video recorder to standby, then press and hold down
»INFO«.
– The display on the video recorder reads something like »
CH 27 RF
«.
6
Set the channel (in this example, channel 27) by pressing »
*
P
Ü
« on the
video
r
ecor
der
or » 0…9« on the r
emote
contr
ol
, until you see the test
picture from the video recorder on the television screen.
7
If the quality of the test picture is OK, press » OK « to save the setting.
– The video switches to standby.
Note:
If the quality of the test picture is unsatisfactory, or if the picture quality of
other channels has deteriorated, then you should find another free channel
on the television and repeat the setting from steps 1 to 5.
You can switch off the station on the video recorder. Fore more information
see the ”Switching the station on the video recorder on and off” on Page 59.