Service manual

Allgemeiner Teil / General Section GV 30…, GV 50…
1 - 30 GRUNDIG Service
USING A DECODER
___________________________________________________________________
ENGLISH
49
Decoder operation with television stations from the
VCR-SAT module
A decoder is necessary when the video recorder receives encoded programs
from a privately operated station. The decoder can only be used for television
stations received through the VCR-SAT module.
Ask for the decoder at your dealer’s.
Connection
1 Connect the PAY-TV decoder to the decoder jack of the VCR-SAT module with
a EURO-AV cable.
Setting the channel position for a decoder
1 Press » i INFO« to call up the main menu.
2 Select the »MODE« line using »
C
« or »
D
« and activate by pressing » OK «.
3 Select the » AV2-IN« line using »
C
« or »
D
« and then press »
Q
« to select
the » DECODER« setting.
4 Press » OK « to save the setting.
OSD-MODE OFF
VCR NO. 1
16:9 AUTO
NTSC PB PAL TV
AUTO POWER OFF OFF
■
➔
AV2–IN DECODER
ɶʺ
:SELECT
‹›
:CHANGE
OK :ENTER INFO:EXIT
TV
DECODER/
EURO-AV2
EURO-AV1
AUDIO
OUT
L
R
AC IN
TV
DECODER/
EURO-AV2
EURO-AV1
AUDIO
OUT
L
R
AC IN
2
3
0
V
5
0
-6
0
H
z
I
N
P
U
T
S
A
T
VCR DEC
9
5
0
-
2
1
5
0
M
H
z
1
4
/
1
8
V
0
,
3
5
A
m
a
x
.
D
O
N
O
T
R
E
M
O
V
E
C
O
V
E
R
S
H
A
Z
AR
D
L
I
V
E
-
P
A
R
TS
SAT-LINK
TV
R
SAT
AV1
AV2
R
L
PAY-TV
1
USING A DECODER
___________________________________________________________________
50
5 Press » i INFO« to open the main menu.
6 Select the » INSTALL« line using »
C
« or »
D
« and then press » OK « to
confirm.
7 Highlight the »CHANNEL SELECTION« line by pressing » OK «.
8 Highlight the »CHANNEL PRESET« line by pressing » OK «.
9 Select the » PRESET« line with »
C
« or »
D
« and enter the desired channel
position, where the satellite station requiring the decoder is located, with
»
F
« or »
E
«.
10 Select the line » SAT-MODULE« with »
C
« or »
D
« and activate » MENU«
by pressing »
F
« or »
E
«.
11 Select the » DECODER« line by pressing »
C
« or »
D
« and select
» ON BB LIN« or »ON BB PAL« or » ON FBAS« by pressing »
F
« or »
E
«.
– The setting depends on the decoder used.
12 Press » OK « to save the setting for this channel position.
13 Press » i INFO« to finish the setting.
Recording PAY TV programs
Preparation
Select the channel position »AV« on the television for the video recorder.
Insert a cassette with enough playing time and the erase-protection tab intact
into the tape compartment of the video recorder.
Recording
1 Before recording, select the PAY TV station using »
C
« or »
D
« or
»
*
P
Ü
«or
»0 ... 9«.
2 Start recording by pressing and holding down »● RECORD«.
– The PAY TV program is recorded.
PROGRAM 1
FREQU.
10964,0 MHZ
POL/ANT. HOR A LOW
AUDIO 7,02/7,20
MHZ
MODE SSTEREO
AUDIO BW 110 KHZ
■
➔
DECODER ON FBAS
LNB LO 1 9 , 750 GHZ
CONTRAST 2 (32)
ŃĽ
:SELECT
ľı
:CHANGE
OK :ENTER INFO:EXIT
PRESET PREM 30
CHANNEL SAT01
SOURCE SAT
■
➔
SAT-MODULE MENU
SKIP OFF
ɶʺ
:SELECT
‹›
:CHANGE
OK :ENTER INFO:EXIT
■
➔
PRESET PREM 30
CHANNEL SAT01
SOURCE SAT
SAT-MODULE MENU
SKIP OFF
0-9 :DATA
ɶʺ
:SELECT
‹›
:CHANGE
OK :ENTER INFO:EXIT