Datasheet

ManualsBrandsCarlo Gavazzi ManualsInductive SensorsInductive Sensor IO-Link 4mm NPN/PNP/Push-Pull 100mA

Carlo Gavazzi Automation S.p.A.

ICS08 IO-Link 3-wire DC

ICS08 IO-Link 3-wire DC DS EN11/05/2018

Miniaturized proximity inductive sensors with IO-Link communication

Description

ICS08 series represents the optimal solution for

industrial automation equipment in applications

where space is limited, but long switching

distance is needed, including tool-selection and

textile machines. The advanced electronics is

encapsulated in a robust stainless steel housing.

The availability of the M8-plug and 2m-PVC cable

connection in short or long housing construction

allows exible mounting.

On-board IO-Link communication opens up many

possibilities, such as easy conguration and set-

up of the devices and advanced parameter setting.

Benets

• A complete family. Available in M8 male thread robust

stainless steel housings with an operating distance of 2

to 4 mm.

• Easy to install. Both ush and non-ush construction

are available. The user can choose between short and

long body housings in 2 m PVC cable or M8-disconnect

plug versions.

• High precision. The onboard advanced microcontroller

ensures better stability with respect to environmental

inuences, with highly repeatable measurements

between -25 and +80°C.

• Easy customization to specic OEM requests:

di󰀨erent cable lengths and materials, special labelling,

customized pig-tail solutions with special cables and

connectors are possible on request.

Only for IO-Link sensors

• The output can be operated either as a switching output

or in IO-Link mode.

• Fully congurable via IO-Link v1.1. Electrical outputs

can be congured as PNP/NPN/Push-pull, normally

open or normally closed.

• Timer functions can be set, such as switch-on and

switch-o󰀨 delay

• Adjustable sensing distance and hysteresis: sensing

distance can be set to 50% or 100% of the maximum

sensing distance

• Temperature monitoring: over or under-run temperature

alarms can be set

•

Applications

• Non contact detection of metal objects in general position-sensing and presence-sensing in industrial applications

• Particularly suitable for rotational speed monitoring thanks to the high operating frequency

Main functions

• Integrated diagnostic function with ashing LED in the event of a short circuit or overload

Summary of content (13 pages)

PAGE 1
ICS08 IO-Link 3-wire DC Miniaturized proximity inductive sensors with IO-Link communication Benefits • A complete family. Available in M8 male thread robust stainless steel housings with an operating distance of 2 to 4 mm. • Easy to install. Both flush and non-flush construction are available. The user can choose between short and long body housings in 2 m PVC cable or M8-disconnect plug versions. • High precision.
PAGE 2
ICS08 IO-Link 3-wire DC IO-Link sensors • The devices can be operated in IO-Link mode once connected to an IO-Link master, or in standard I/O mode. • In IO-Link mode the switching signals of the sensor are made available in the process data via the IO-Link interface. • Several sensor functions can be set via the IO-Link interface: ►► Adjustable switching distance: 50% or 100% of the maximum switching distance. ►► Adjustable hysteresis: standard or increased value.
PAGE 3
ICS08 IO-Link 3-wire DC Selection guide M8 extended range, short housing Connection Cable Plug Cable Plug Rated operating distance Sn Detection principle 2 mm Flush 4 mm Nonflush Ordering no. NPN, Normally open Ordering no. PNP, Normally open Ordering no. NPN, Normally closed Ordering no.
PAGE 4
ICS08 IO-Link 3-wire DC Structure ICS08 A B C A B C D A B C D Element A B Component Sensing face 2 nuts C LED D M8, 3 pin, male connector 11/05/2018 ICS08 IO-Link 3-wire DC DS EN Function Flush or non-flush For sensor mounting Yellow LED: Output flashing: short circuit or overload indication For plug versions only Carlo Gavazzi Automation S.p.A.
PAGE 5
ICS08 IO-Link 3-wire DC Sensing Detection Rated operating distance Sn 2 mm flush or 4 mm non-flush The operating distance is measured according to IEC 60947-5-2, using a standard target moving axially. This target is square shape 1 mm thickness, made of steel e.g. type Fe 360 as defined in ISO 630 and it shall be of the rolled finish.
PAGE 6
ICS08 IO-Link 3-wire DC Fe360 : Steel CrNi : Chrome-nickel CuZn : Brass Al : Aluminium Cu : Copper Sr : Effective operating distance Fig. 3 The rated operating distance is reduced by the use of metals and alloys other than Fe360. The most important reduction factors for inductive proximity sensors are shown in the figure.
PAGE 7
ICS08 IO-Link 3-wire DC Response times Operating frequency (f) ≤ 2 KHz Indication Standard IO mode: Yellow LED Output OFF OFF ON ON Blinking f: 2Hz f: 1Hz Description N.O. output, target not present N.C. output, target present N.O. output, target present N.C. output, target not present Short-circuit or overload Temperature alarm (if enabled) IO-Link mode: • LED is ON for 0.75 s and OFF for 0.
PAGE 8
ICS08 IO-Link 3-wire DC Mechanical data Weight (including 2 nuts and the packaging) max. Mounting Material Max tightening torque Cable version: short, flush: 44.8g; short, non-flush: 44.9g; long, flush: 47g; long, non-flush: 47.1g; Plug version: short, flush: 16g; short, non-flush: 16.1g; long, flush: 18.4g; long, non-flush: 18.5g. Flush mountable or non-flush mountable Housing: stainless steel AISI304 Front cap: Grey thermoplastic polyester 7 Nm Electrical connection Cable Plug 2m, 3 x 0.14 mm2, Ø3.
PAGE 9
ICS08 IO-Link 3-wire DC Connection Diagrams 1 BN + 4 BK 4 BK 3 BU 3 BU - Fig. 4 NPN - Normally open 1 BN + 1 BN - Fig. 5 NPN - Normally closed + 1 BN + 4 BK 4 BK 3 BU 3 BU - Fig. 6 PNP - Normally open - Fig. 7 PNP - Normally closed 1 BN 4 BK 3 BU + Out/IO-Link - Fig. 8 IO-Link BN: brown 11/05/2018 ICS08 IO-Link 3-wire DC DS EN Colour code BK: black BU: blue Carlo Gavazzi Automation S.p.A.
PAGE 10
ICS08 IO-Link 3-wire DC Dimensions [mm] ICS08 [mm] 4 4 SW13 SW13 LED 30 31 3 4 Ø2 LEDx4 M8x1 4 29 4 1 31 SW13 43 40 Fig. 11 Short body, flush version, plug 4 Ø2 LEDx4 4 7 29 3 7 3 M8x1 SW13 Fig. 10 Short body, non-flush version, cable M8x1 31 M8x1 4 4 1 30 34 3 Fig. 9 Short body, flush version, cable Ø3.2 Ø3.2 M8x1 M8x1 LED Fig. 12 Short body, non-flush version, plug 4 SW13 SW13 LED 45 46 4 1 3 Fig.
PAGE 11
ICS08 IO-Link 3-wire DC Installation M8 flush d ≥ 3 x Sn d d d ** Fig. 17 Flush sensor, when installed in damping material Fig. 18 Flush sensors, when installed together in damping material M8 non-flush ≥ 2 x Sn ≥ 3 x Sn ≥3xd d ** Fig. 19 Non-flush sensor, when installed in damping material 11/05/2018 ICS08 IO-Link 3-wire DC DS EN d d 2xd d d Fig. 20 Non-flush sensors, when installed together in damping material Carlo Gavazzi Automation S.p.A.
PAGE 12
ICS08 IO-Link 3-wire DC Sensors installed opposite each other ≥ 6 x Sn Fig. 21 For sensors installed opposite each other, a minimum space of 6 x Sn (the nominal sensing distance) must be observed ** Free zone or non-damping material Sn: nominal sensing distance d: sensor diameter: 8 mm Delivery contents and compatible components Delivery contents • • • • Inductive proximity switch 2 fixing nuts 2 lock washers Packaging: plastic bag CARLO GAVAZZI compatible components • Mounting bracket AMB8...