Table of Contents Tools Needed Mounting Options 1.888.227.2178 Ceiling Bracket 30 inches To register your fan, please visit: www.CasablancaFanCo.com/register Wiring M8515-01 • 11/15/18 • © 2018 Casablanca Fan Company ? 19 ? ? 20 PA G E 1 12 Troubleshooting PA G E 14 PA G E PA G E 13 11 Maintenance & Cleaning Wall Control 5 Blades PA G E 9 PA G E Globe 4 Canopy PA G E 6 Save your receipt for proof of purchase.
What to Expect with Your Installation www.CasablancaFanCo.com 1.888.227.2178 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Ceiling angles greater than 34° will require an Angled Mounting Kit.
Tools Needed www.CasablancaFanCo.com Tools Needed Ladder Screwdrivers Pliers Power Drill (optional) Wire Strippers 9/64” Drill Bit (optional) If mounting to a support structure, you will also need these tools. 3 M8515-01 • 11/15/18 • © 2018 Casablanca Fan Company Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step. 1.888.227.
34O CEILING Mounting Options OPTION 1 If you have a flat ceiling: Standard Mounting 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately). Angled Mounting Standard Mounting Style Ceiling Outlet Box (required) Use the three steps below to determine if your ceiling angle is greater than 34° 2 1 1.888.227.
Ceiling Bracket www.CasablancaFanCo.com 1.888.227.2178 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
Option 1 Downrod www.CasablancaFanCo.com FAN FALL HAZARD To prevent SERIOUS INJURY or DEATH: Option 3 Included (pre-assembled) If you need a different downrod length follow these steps: Longer Downrod for angled ceilings or ceilings 10’ or higher Steps 1-5 to remove standard downrod pipe 1 2 3 • ALWAYS follow the downrod assembly instructions exactly. • VERIFY the downrod is assembled correctly by firmly pulling on the hanger ball.
Downrod (continued) KEEP! (not to scale) 8” & 3/8” 1.888.227.2178 STRIP CUT www.CasablancaFanCo.com ! KEEP Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. Remove the pre-installed setscrew so that the downrod can be inserted. WARNING The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops.
Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. www.CasablancaFanCo.com DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 8 M8515-01 • 11/15/18 • © 2018 Casablanca Fan Company NOTICE To prevent damage to fan, ALWAYS lift holding either the fan housing or the downrod. 1.888.227.
Wiring Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. www.CasablancaFanCo.com 1.888.227.2178 OM CEILING FR Receiver green/yellow stripe (grounding) Using an orange wire connector from the hardware bag: Connect the 3 grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and ceiling bracket.
Wiring (continued) www.CasablancaFanCo.com OM FR OM CEILING FR • Connect the blue wire from the receiver to the blue wire (or possibly black with white stripe wire) from the fan. • Connect the white (grounded) wire from the ceiling to both the white wire from the receiver and the white wire from the fan. FRO white FR M FA N OM FAN FR OM white Connect the black (ungrounded) wire from the ceiling to the black wire from the receiver.
Canopy www.CasablancaFanCo.com Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. 11 M8515-01 • 11/15/18 • © 2018 Casablanca Fan Company 1.888.227.
Blades www.CasablancaFanCo.com Attach a blade tip to each blade using two blade tip screws, found in the hardware bag. Insert four blade assembly screws and four blade washers, found in the hardware bag, into each blade as shown. Install the screws into the posts in each blade arm. 12 M8515-01 • 11/15/18 • © 2018 Casablanca Fan Company 1.888.227.
Globe www.CasablancaFanCo.com 1.888.227.2178 Tab Notch Globe CONGRA T YOU’REULATIONS! DONE! Position the notches in the outer rim of the globe so they line up with the tabs on the inside of the rim on the light kit. Carefully lift the globe up inside the light kit as far as it will go, then rotate the globe clockwise until it is held tightly in place by the four tabs. WARNING GLASS FALL HAZARD To prevent SERIOUS INJURY or DEATH, make sure that glass is properly secured.
Wall Control For Single Switch www.CasablancaFanCo.com If you have a dual switch setup, go to page 18 for dual switch installation instructions. 3 Installing the Wall Plate Bracket 4 Wiring the Wall Control Snap the Wall Control into the Wall Plate Bracket. off the power 1 Turning Ensure the power is OFF at the outlet box and wall switch location before proceeding with installation.
Wall Control For Single Switch 5 6 www.CasablancaFanCo.com Installing the Wall Control 7 Install the longer screws through the slots in the wall control into the switch box screw holes. Turning on the power IMPORTANT n Tur 8 Installing the Wall Plate Push the wall plate onto the Wall Plate Bracket. It should snap into place. 1.888.227.
Wall Control For Dual Switches www.CasablancaFanCo.com which switch controls the fan light. 2 Verify 1. Turn on power for the fan. To install the Casablanca Wall Control into a dual switch location, you will need a wall plate with both a standard switch and rocker switch cut-out (sold separately). 2. Push both existing wall switches to the on position. If you are unfamiliar or uncomfortable with wiring, please contact a qualified electrician. 1 To access the battery compartment, n Tur er Pow 3.
Wall Control For Dual Switches 4 5 www.CasablancaFanCo.com 7 Remove the existing wall plate Remove the existing wall plate. Save the screws. You will need them for the existing, marked light switch. Install the Wall Plate Install the wall plate that fits your setup (sold separately). 1. Use the screws you saved to reinstall into the light switch. Remove the Casablanca Wall Control frame. 2. Use the screws included Remove the frame from the Casablanca Wall Control.
Wall Control www.CasablancaFanCo.
Maintenance & Cleaning www.CasablancaFanCo.com er w o nP r Tu OFF Be sure to turn off power to the fan before performing any maintenance or relamping. Cleaning the fan - use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. 19 M8515-01 • 11/15/18 • © 2018 Casablanca Fan Company 1.888.227.
Troubleshooting www.CasablancaFanCo.com Fan doesn’t work Excessive wobbling Remote does not work • Press a fan speed button. • Tighten all of the blade screws until they are snug. • Make sure the battery is installed correctly. • Turn the power off, support the fan carefully, and check that the hanger ball is properly seated. • Install a new battery. • Check the circuit breaker to ensure the power is turned on. • Check the wall control battery. • Make sure the blades spin freely.
Troubleshooting (continued) www.CasablancaFanCo.com Installing Multiple Fans with Independently Operating Remote Controls 1.888.227.2178 Installing One Fan Operating on Multiple Remote Controls To install multiple fans with independently operating remote controls, there is no need to perform any pairing procedures. Each set of receiver/transmitter is already paired. Simply install each receiver into a fan and use the appropriate transmitter to operate each fan.
