Table of Contents www.CasablancaFanCo.com What to Expect with Your Installation Ceiling Plate Preparation 1.888.227.
What to Expect with Your Installation www.CasablancaFanCo.com 1.888.227.2178 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box 7 feet from bottom edge of blade to the floor Know your wiring Assess location You may need a friend to help you.
Preparation www.CasablancaFanCo.com Screwdrivers Wire Strippers Ladder 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M8552-01 • 03/04/19 • © 2019 Casablanca Fan Company 1.888.227.
Ceiling Bracket www.CasablancaFanCo.com 1.888.227.2178 Bumper r we o nP r Tu OFF Make sure all four bumpers are still attached. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box.
www.CasablancaFanCo.com Ceiling Plate Hook (not to scale) 8” Ceiling Plate Hook & 3/8” 1.888.227.2178 STRIP CUT Hanging the Fan Raise the fan and align the slots in the canopy with the hooks on the ceiling plate. Note: To hang the fan, you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate hooks. The wires can be cut, but leave at least 8” extending from the top of the canopy. 8” Place the slots over the ceiling plate hooks to hang the fan.
Wiring: Single Switch www.CasablancaFanCo.com Dual Switch Instructions Have a single switch? Follow these steps: din g ro un Un Black g ipe un Str ing und Gro Connect the grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, ceiling plate, and the fan. Blue Connect the black (ungrounded) wire from the ceiling to the black wire from the fan.
Wiring: Dual Switch www.CasablancaFanCo.com Have dual switches? Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. Follow these steps: un Grounded gro Un un g ow din e rip St Black Blue ll Ye Gro Connect the second ungrounded (light) wire from the ceiling to the blue wire from the fan.
Canopy www.CasablancaFanCo.com 1.888.227.2178 Canopy Trim Ring Screw Holes Canopy Screw Canopy Trim Ring Screw Swing the fan up to align the canopy screw holes with the mounting holes on the ceiling plate. Note: The slots in the canopy must remain engaged while swinging the canopy for alignment. Hold the canopy up with the screw holes aligned. When all the holes are properly aligned, securely tighten all three canopy screws found in the hardware bag.
Blades www.CasablancaFanCo.com Put each blade washer, found in the hardware bag, onto a blade screw, found in the hardware bag. Then secure each blade to a blade iron using the blade screws and washers. 9 M8552-01 • 03/04/19 • © 2019 Casablanca Fan Company 1.888.227.
Switch Housing www.CasablancaFanCo.com Screw two switch housing assembly screws, found in the hardware bag, halfway into the mounting plate on the bottom of the motor housing. It does not matter which two screw holes you choose. Feed the two single-pin connectors through the center hole of the upper switch housing, then wrap the keyhole slots around the screws and twist counterclockwise. 10 M8552-01 • 03/04/19 • © 2019 Casablanca Fan Company 1.888.227.
Light Kit www.CasablancaFanCo.com Insert the third screw, found in the hardware bag, into place and then tighten all three screws. Screw two LED assembly screws, found in the hardware bag, halfway into the Switch housing. It does not matter which two screw holes you choose. WARNING FAN FALL HAZARD Make sure screws are tight to secure the upper switch housing to the mounting plate. 11 M8552-01 • 03/04/19 • © 2019 Casablanca Fan Company 1.888.227.
Light Kit (continued) Connect the single-pin connectors from the LED assembly to the connectors from the fan. Connect the white wires together. Connect the blue and black wires together. Tuck the excess wiring above the LED assembly. www.CasablancaFanCo.com Wrap the keyhole slots around the screws and twist counterclockwise. Insert the third screw, found in the hardware bag, into place and then tighten all three screws. WARNING FAN FALL HAZARD 12 M8552-01 • 03/04/19 • © 2019 Casablanca Fan Company 1.
Light Kit (continued) www.CasablancaFanCo.com 1.888.227.2178 Tab Notch CONGRA T YOU’REULATIONS! DONE! Position the notches in the outer rim of the globe so they line up with the three tabs on the inside rim of the housing. Carefully lift the globe up inside the housing as far as it will go, then rotate the globe clockwise until it is held tightly in place by the tabs.
Wall Control For Single Switch www.CasablancaFanCo.com If you have a dual switch setup, go to page 18 for dual switch installation instructions. 1 Installing the Wall Plate Bracket 4 Wiring the Wall Control Snap the Wall Control into the Wall Plate Bracket. Turning off the power Ensure the power is OFF at the outlet box and wall switch location before proceeding with installation. n Tur 2 3 Installing the battery To access the battery compartment, slide the battery door up. er Pow OFF 1.
Wall Control For Single Switch 5 6 www.CasablancaFanCo.com 7 Installing the Wall Control Install the longer screws through the slots in the wall control into the switch box screw holes. Turning on the power IMPORTANT n Tur 8 Installing the Wall Plate Push the wall plate onto the Wall Plate Bracket. It should snap into place. 1.888.227.
Wall Control For Dual Switches www.CasablancaFanCo.com 2 To install the Casablanca Wall Control into a dual switch location, you will need a wall plate with both a standard switch and rocker switch cut-out (sold separately). If you are unfamiliar or uncomfortable with wiring, please contact a qualified electrician. (Sold Separately) 1 Installing the battery To access the battery compartment, slide the battery door up. Battery Door Replace the used battery with two AAA batteries when needed. 1.888.
Wall Control For Dual Switches 4 Remove the existing wall plate 5 Remove the Casablanca Wall Control frame. www.CasablancaFanCo.com 7 Remove the existing wall plate. Save the screws. You will need them for the existing, marked light switch. 6 8 Wiring the Casablanca Wall Control 1. 2. 3. 4. Install the Wall Plate Install the wall plate that fits your setup (sold separately). 1. Use the screws you saved to reinstall into the light switch. 2. Remove the frame from the Casablanca Wall Control.
Wall Control www.CasablancaFanCo.
Maintenance & Cleaning www.CasablancaFanCo.com er w o nP r Tu OFF Be sure to turn off power to the fan before performing any maintenance. Cleaning the fan - use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. 19 M8552-01 • 03/04/19 • © 2019 Casablanca Fan Company 1.888.227.
Troubleshooting Fan doesn’t work • Press a fan speed button (up or down arrow. • Check the circuit breaker to ensure the power is turned on. • Check the wall control battery. • Make sure the blades spin freely. • Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram. www.CasablancaFanCo.com Fan keeps spinning after power is turned off • The blades may take a few minutes to come to a complete stop.
Troubleshooting (continued) www.CasablancaFanCo.com Installing Multiple Fans with Independently Operating Remote Controls 1.888.227.2178 Installing One Fan Operating on Multiple Remote Controls To install multiple fans with independently operating remote controls, there is no need to perform any pairing procedures. Each set of receiver/transmitter is already paired. Simply install each receiver into a fan and use the appropriate transmitter to operate each fan.