Installation Guide

ManualsBrandsCascadia Lighting ManualsChandeliersTFKM5103VB

INSTRUCTION SHEET IS-TFKM5103

STYLE NUMBER:

TFKM5103VB, TFLR5103VB

ISSUED 08-2010 REVISED 2010-08-20

PACKAGE CONTENTS

PART

DESCRIPTION

QUANTITY

A Crossbar

1pc

2pcs

1pc

2pcs

1pc

Green Ground Screw

Hex Nut

Nipple

Lock Washer

Canopy Chain Loop

Canopy Lock Ring

Fixture Chain

Ceiling Canopy

Socket Assembly

1OF6

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

WARNING:

CAUTION:

● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching

off the circuit breaker or removing the fuse.

● These instructions are provided for your safety. It is very important that they are read completely before the

installation of your fixture. We strongly recommend that a professional electrician install the fixture.

● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb9s) had sufficient

time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.

WARNINGS AND CAUTIONS

● Before beginning installation of product, make sure all parts are present. Compare parts with package contents

list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the

product. Contact customer service for replacement part.

● Estimated Assembly Time: 30 - 45 minutes

● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,

Wire cutter, Safety glasses and (3) 100W A19 medium base bulbs

● Helpful Tools (not included): Wire strippers.

PREPARATION

1pc

3pcs

Fixture Loop

Center Column

Check Ring

Finial

Socket Collar

Side Chain

Shade

Summary of content (6 pages)

PAGE 1
6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel .
PAGE 2
INSTALLATION INSTRUCTIONS STYLE NUMBER: TFKM5103VB, TFLR5103VB STEP 1: a. Place the Check Ring over the nipple on the top center of the Socket Assembly. Then thread the Center Column onto the Socket Assembly as shown. Handtighten until snug. Center Column Socket Assembly Check Ring STEP 2: a. Thread the Fixture Loop onto the nipple in the top center of the Fixture Canopy. Hand-tighten until snug. Fixture Loop Fixture Canopy STEP 3: a.
PAGE 3
INSTALLATION INSTRUCTIONS STYLE NUMBER: TFKM5103VB, TFLR5103VB STEP 4: a. Attach the close end of the Side Chain to the Hook at the side of the Fixture Canopy. Attach the open end of the Side Chain to the Hook at the Support Arm. Fixture Canopy Hook Side Chain Support Arm Hook STEP 5: a. Secure the Crossbar onto the Outlet Box with Outlet Box Screws. Tighten until snug. Outlet Box Crossbar Outlet Box Screw STEP 6: a. Thread one Hex Nut onto top end of the Nipple. b.
PAGE 4
INSTALLATION INSTRUCTIONS STYLE NUMBER: TFKM5103VB, TFLR5103VB STEP 7: a. Thread another Hex Nut onto the end of the Nipple. b. Place the Lock Washer over the end of the Nipple and then thread the Canopy Chain Loop onto the end of the Nipple. c. Using pliers, thread the Hex Nut against the Canopy Chain Loop and hand-tighten until snug. Nipple Hex Nut Lock Washer Canopy Chain Loop STEP 8: a. Push the Ceiling Canopy upward over the Outlet Box.
PAGE 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: TFKM5103VB, TFLR5103VB STEP 10: a. Pull the Supply Wires up through the Fixture Chain alternating links. Push the wires up through the Canopy Chain Loop into the outlet box. Canopy Chain Loop Fixture Chain Supply Wires STEP 11: a. Un-thread the Canopy Lock Ring and slide Canopy Lock Ring and Ceiling Canopy down the Fixture Chain. b. Push all slack fixture wire through Canopy Chain Loop into Outlet Box. Trim excess fixture wire leaving a minimum of 6 in.
PAGE 6
INSTALLATION INSTRUCTIONS STYLE NUMBER: TFKM5103VB, TFLR5103VB STEP 12: Use Wire Connectors to connect the wires. a. Connect the House Ground Wire to the Fixture Ground Wire. b. Connect the House White (or Ribbed) Wire to the Fixture Supply Wire (Black or Smooth Side). c. Connect the House Black (or Red) Wire to the Fixture Supply Wire (Black or Smooth Side). d. Wrap each connection with approved electrical tape and carefully stuff all of the connected wires into the Outlet Box.