Installation Guide

1. Attach nipple(-a) to the mounting strap, then secure it with a washer and hex
nut.
2. Attach the mounting strap to the outlet box by using two mounting screws.
3. Secure the top loop to nipple(-a).
4. Carefully attach the upper fixture onto the holder by securing the rod to nipple(-b).
5. Adjust the arms of the fixture according to the drawing of the package.
Important:
a. The arms should be positioned with equal distances between them.
b. The arms should be fixed securely.
6. Attach the silhouettes to the holder by aligning holes, and then secure them with
set screws. (See Figure 1)
a. Use the tree side of the silhouettes which marked "P-T" or "P-Y" or "P-H"
touch the holder.
b. You can install the silhouettes which marked P-Y (for CH55405) or marked
P-L (for CH55505) or marked P-H (for CH55705) to the location of silhouettes
which marked P-T (for CH55605) shown in right graph to replace them.
7. Choose the length of the chain you need, then weave the fixture wire and the
fixture grounding wire through the chain, collar and canopy.
8. Connect one end of the chain with the loop by using a loop lock.
9. Connect the other end of the chain with the top loop by using another loop
lock.
10. Thread the fixture wire and fixture grounding wire through the top loop,
nipple(-a) and mounting strap.
11. Pull out the outlet wires and house grounding wire from the outlet box.
Make wire connections using the wire nuts:
---The smooth wire (marked) from the fixture to the black wire from
the power source.
---The ridged wire (unmarked) from the fixture to the white wire
from the power source.
---Attach the fixture grounding wire to the mounting strap with
the green grounding screw. Then connect it to the house
grounding wire with a wire nut.
Carefully put the wires back into the outlet box.
12. Attach the canopy to the mounting strap by inserting the
top loop, then secure it with the collar.
13. Screw nipple(-c) into coupling, secure it with a hex nut.
Then attach the cover upward to the holder by inserting
nipple(-c), secure it with finial.
14. Attach the glass shades to the glass holders, then secure
them with socket rings.
15. Install bulbs (not included). See relamping label at socket
area or packaging for maximum allowed wattage.
16. Turn on the power at the main fuse or circuit breaker box.
Fixture Wire
Loop
Rod
Arm
Nipple(-b)
Silhouette
Marked "P-T"
Holder
Coupling
Hex Nut
Nipple(-c)
Cover
Finial
Glass Holder
Glass Shade
Socket Ring
Chain
Mounting Screw
Nipple(-a)
Fixture Grounding
Wire
Collar
Top Loop
Canopy
Mounting Strap
Green Grounding Screw
Hex Nut
Wire Nut
Washer
Outlet Box
House Grounding Wire
Loop Lock
Loop Lock
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.
CH55405 / CH55505 / CH55605 / CH55705
Upper Fixture
Set Screw
110319
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
There are labels
attached on the
back of each
silhouette, such
as P-Y, P-L, P-T
and P-H.
Figure.1
P-Y (5pcs)
(For CH55405)
P-L (5pcs)
(For CH55505)
P-T (5pcs)
(For CH55605)
P-H (5pcs)
(For CH55705)
Bulb Type A Max.100W
(not included)