Installation Guide

ManualsBrandsCascadia ManualsChandeliersTwirl 5-Light Venetian Bronze Coastal Shaded Chandelier

1. Thread the top assembly onto the fixture.

2. Rod Connections:

a. Thread the fixture wire from the top assembly through the

lower rod, then secure the lower rod onto top assembly

using the threaded pipe.

b. Thread the fixture wire through the middle rod, and then

secure the middle rod onto the lower rod using the threaded

pipe.

c. Thread the fixture wire through the upper rod, and then secure

the upper rod onto the middle rod using the threaded pipe.

The height can be adjustable to 19", 25", 31", 37", 43", 49",

55", 61", 67"or 73" by using the rods.

3. Thread the fixture wire through the collar, coupling kit, canopy,

then secure the rod assembly to the coupling kit. secure the

threaded nipple by tightening the set screw.

4. Thread the fixture wire through the nipple-1, hex nut and

mounting strap. Install the hex nut onto one end of

the nipple-1 leaving about 3/8” (10mm) thread

exposed. Install the same end of nipple-1 by

screwing into coupling kit, secure nipple-1 by

tightening hex nut.

5. Attach the nipple-1 to the mounting strap,

then secure it with hex nut.

6. Attach the mounting strap to outlet box by

using two mounting screws.

7. Pull out the outlet wires and the house

grounding wire from the outlet box. Make

wire connections using the wire nuts:

---The black wire from fixture to the black

wire from power source.

---The white wire from fixture to the white

wire from power source.

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT

BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THESE INSTRUCTIONS.

H0040 / H0042 / H0043

120807

Contents of Spare Parts:

Assembly Kit

(1 SET)

(4555MM)

(For all items)

Bulb

(1 PC)

(8051HL)

(For all items)

Exterior Shade

(4 PCS)

(9352FS)

(For all items)

Collar

Canopy

Outlet Box

House Grounding Wire

Wire Nut

Nipple-1

Mounting Strap

Green Grounding Screw

Hex Nut

Mounting Screw

Upper Rod

Middle Rod

Lower Rod

Threaded Pipe

Fixture Wire

Fixture

Interior Shade

3-Way Switch

Bulb Type A-15 Max.60W

(Not Included)

Coupling Kit

Fixture Grounding Wire

Hex Nut

Socket

Threaded Pipe

Top Assembly

Set Screw

Threaded Pipe

Exterior Shade

Suction Cap

Bulb GU10 Max.35W

(included)

Lamp Holder

Threaded Pipe

6” Rod

(1 PC)

(4556RR)

(For all items)

12” Rod

(4 PCS)

(4555RR)

(For all items)

Suction Cap

(1 PC)

(4555SP)

(For all items)

Interior Shade

(4 PCS)

(9355IS)

(For H0040)

Interior Shade

(4 PCS)

(9354IS)

(For H0042)

Holder

Parts for H0042

Parts for H0043

Summary of content (2 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS H0040 / H0042 / H0043 WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.
PAGE 2
---Attach the fixture grounding wire to the mounting strap with the green grounding screw. Then connect it to the house grounding wire with the wire nut. Carefully put the wires back into the outlet box. 8. Attach the canopy to the mounting strap, and secure it with collar. 9. Place the interior shades onto the fixture, then place the exterior shades onto the fixture, making sure the shades at the center of holders.