User manual

ManualsBrandsCasio ManualsWatch1382

1382-1

CNT indicator

Language indicator

ENG

(English)

ESP

(Spanish)

ITA

(Italian)

FRA

(French)

DEUT.

(German)

Press D

Press A

GMT

differential

Auto 

Receive

Language

DST Seconds

HourMinutesYearMonthDateCNT

12/24-Hour

format

Receive indicator

▼

▲

PM indicator

Month-Date

Seconds

Hour : Minutes

Day of week

Time/Date

Date

Seconds

Analog

▼

▲

Module No. 1382

• Press C to change from mode to mode. After you perform an operation in

any mode, pressing C returns to the Timekeeping Mode.

GENERAL GUIDE

▼

▲

▼

Timekeeping Mode

Telememo Mode World Time Mode

▼

Hand Setting Mode

Stopwatch Mode Alarm Mode

• Press L in any mode to illuminate the display for about two seconds.

Press C

TIMEKEEPING MODE

In addition to time and date settings, the Timekeeping Mode also lets you

adjust the contrast of the digital display.

• The Timekeeping Mode is actually made up to four sub-modes. Press D to

switch between the sub-modes.

• This watch displays text for the day of the week in any one of the five

different languages (English, German, French, Italian, and Spanish).

• See the “Day of the Week List” at the back of this manual for information on

abbreviations used.

About Manual Time Setting and Time Calibration

Signal Reception

The current time for this watch can be set by inputting the time and date you

want (manual setting) or by a time calibration signal. Note that the time

calibration signal is available only in certain areas in Europe. For details on

time calibration reception and the areas in which the time calibration signal is

available, see the section of this manual titled: “TIME CALIBRATION SIG-

NAL RECEPTION.”

To set the current time manually

1. Press B while in the Timekeeping Mode.

The current Auto Receive on/off setting

flashes on the display because it is

selected

• The receive indicator also flashes along with

the current on (

ON) /off (OFF) setting.

2. Press C to change the selection in the

following sequence.

• The Auto Receive, DST, and GMT differential settings are used for time

calibration signal reception only. For details on these settings, see the

section of this manual titled: “TIME CALIBRATION SIGNAL RECEPTION.”

• See the section of this manual titled “To adjust the display contrast” for

details on using the CNT (contrast) setting.

3. Press C until the language indicator is

flashing on the display.

• The language indicator shows the language

currently set for the day of the week.

• The day of the week is set automatically in

accordance with the date.

4. Use A and D to change the language

setting in the following sequence.

5. Press C until the 12/24-hour indicator is flashing on the display.

•

12H indicates 12-hour format, while 24H indicates 24-hour format.

6. Press D to toggle between the 12-hour (

12H) and 24-hour ( 24H) formats.

• With the 12-hour format, the P (PM) indicator appears to the left of the

digital time for times in the range of noon to 11:59 pm. Times from midnight

to 11:59 am are shown without any indicator.

• With the 24-hour format, times are indicated in the range of 00:00 to 23:59,

with a 24 indicator to the left of the digital time.

7. Press C until the seconds digits are flashing on the display.

8. Press D to reset the seconds to

00.

• If you press D while the seconds count is in the range of 30 to 59, the

seconds are reset to

00 and 1 is added to the minutes. If the seconds

count is 00 to 29, the minutes count is unchanged.

9. Press C until the hour digits are flashing on the display.

10.Press D to increase the setting or A to decrease it. Holding down either

button changes the setting at high speed.

11.Repeat steps 9 and 10 to set the minutes, year, month, and date.

12.After you make the settings you want, press B to return to the

Timekeeping Mode.

• When you use the above procedure to set the digital display time, the hands

of the analog timepiece normally adjust according to your setting. If, for any

reason, the digital time does not match the analog time, use the procedure

described under “HAND SETTING MODE” to match the analog setting with

the digital display.

• The date can be set within the range of January 1, 1995 to December 31, 2039.

• If you do not operate any button for a few minutes while a selection is

flashing, the flashing stops and the watch goes back to the Timekeeping

Mode automatically.

To adjust the display contrast

1. Press B while in the Timekeeping Mode.

The current Auto Receive on/off setting

flashes on the display because it is

selected

2. Press C 11 times until the

CNT (contrast)

indicator is flashing on the display.

• The value to the right of the

CNT indicator

shows the current contrast setting. You can

set the contrast to a value from 1 (lightest) to

7 (darkest).

3. Use D to increase the contrast value and A to decrease it.

4. After you make the setting you want, press B to return to the Timekeeping

Mode.

Summary of content (5 pages)

PAGE 1
Module No. 1382 1382-1 GENERAL GUIDE • Press C to change from mode to mode. After you perform an operation in any mode, pressing C returns to the Timekeeping Mode. • Press L in any mode to illuminate the display for about two seconds.
PAGE 2
1382-2 About the backlight In any mode, press L to illuminate the display for about two seconds. • The backlight of the watch employs an electro-luminescent (EL) panel, which loses illuminating power after very long use. • The illumination provided by the backlight may be hard to see when viewed under direct sunlight. • The watch will emit an audible sound whenever the display is illuminated. This is caused by a transistor that vibrates when the EL panel lights up.
PAGE 3
1382-3 About Auto Receive When auto receive is turned on, the watch automatically starts to receive the time calibration signal when the digital time in the Timekeeping Mode reaches 2:00 AM and 4:00 AM each day (calibration times). • The Auto Receive operation is performed only if the watch is in the Timekeeping Mode or World Time Mode when one of the calibration times is reached. It is not performed if the time is reached while you are making settings (while settings are flashing on the display).
PAGE 4
1382-4 How time is kept in the World Time Mode When you set the time for any time zone, all other zones are adjusted accordingly. The World Time Mode time setting can be made manually or by Auto Receive of the time calibration signal. When Auto Receive is turned on in the Timekeeping Mode, successful receipt of the time calibration signal causes all World Time Mode times to be adjusted in accordance with Berlin time.
PAGE 5
1382-5 Day of the Week List ENG : SUN (Sunday), MON (Monday), TUE (Tuesday), WED (Wednesday), THU (Thursday), FRI (Friday), SAT (Saturday) (English) DEUT.