DT-X11 Series Hardware Manual (Version 1.01) CASIO Computer Co., Ltd. Copyright ©2006. All rights reserved.
Table of Contents Chapter 1. 1.1. 1.2. 1.2.1. 1.3. 1.3.1. 1.3.2. 1.3.3. 1.3.4. 1.3.5. Chapter 2. 2.1. 2.2. 2.3. 2.4. 2.5. 2.6. 2.7. 2.8. 2.9. Chapter 3. 3.1. Chapter 4. Chapter 5. 5.1. 5.1.1. 5.1.2. 5.1.3. 5.1.4. 5.1.5. 5.1.6. 5.2. 5.2.1. 5.2.2. 5.2.3. 5.2.4. 5.2.5. 5.2.6. 5.3. 5.3.1. 5.3.2. 5.3.3.
5.3.4. 5.3.5. 5.4. 5.4.1. 5.4.2. 5.4.3. 5.5. 5.5.1. 5.5.2. Chapter 6. 6.1. 6.2. Chapter 7. 7.1. 7.2. 7.2.1. 7.2.2.
Editorial Record Manual Version no. 0.90 1.00 1.01 Date edited February 2006 March 2006 August Page 8 26 Content Tentative version Original version The content in Table 1.2 of Chapter 1.2 is corrected. The content in Table 2.9 of Chapter 2.7 is corrected.
Preface This reference manual describes about the CASIO DT-X11 series handheld terminals with C-MOS imager or Laser Scanner integrated. A new generation of handheld terminal has been developed. CASIO introduces the revolutionary DT-X11 series of handheld terminal with built-in Intel® PXA255 Application Processor, C-MOS imager or 1D bar code scan engine and diverse wireless LAN communications via Bluetooth, IEEE802.11b WLAN and WAN card. Running under Microsoft® Windows® CE 5.
1. Overview of the Products 1.1 Features Incorporates .NET technology • Uses WindowsCE 5.0 operating system. • Makes effective use of .NET resources developed by other corporations. • Employment of eMbedded OS makes it possible to build a flexible WindowsCE system. Enhanced communicating functions • Covers GPRS/WLAN, etc. by using various communication cards. • Built with Bluetooth® Ver1.2 module.
Aiming to a full compliance with the “Restriction of the use of certain Hazardous Substances in electronic equipment (RoHS)” set mandatory on July 1 2006 The following products have been assembled with devices, components and parts manufactured using Lead (Pb) free solder.
1.2 Available Models Table 1.1 List of models Model Scan Engine DT-X11M10E DT-X11M10RC DT-X11M30E DT-X11M30U DT-X11M30RC Laser Scanner Laser Scanner C-MOS Imager C-MOS Imager C-MOS Imager Table 1.2 Wireless Communication Bluetooth IEE802.
1.2.1 Options and Interfaces DT-X11 USB Port (Ver1.1 Function) PC IrDA Printer , etc. USB RS-232C IrDA Port (IrDA 1.1) Bridge Satellite Cradle DT-160IOE RS-422 AC Adaptor AD-S42120A-E Power Supply Terminals (Built-in Charge Circuit) PC RS-422 Bridge Satellite Cradle DT-160IOE Cradle-type Battery Charger DT-169CHGE AC Adaptor AD-S42120A-E AC Adaptor AD-S42120A-E Car Mounted Battery Charger DT-167CHGE Car Power Cable DT-827CAC PCMCIA WLAN integrated Models. without WLAN models.
1.3 General Guide 1.3.1 DT-X11 Left Front 15 1 2 Right Back 22 3 16 23 17 24 4 20 18 6 14 19 5 7 18 8 13 10 25 9 11 21 12 Fig. 1.2 Table 1.4 Names of parts No. 1 Name Indicator 1 2 Indicator 2 3 LCD Panel/Touch Screen 4 5 6 Buzzer Power Key Cursor Keys 7 8 9 Programmable Key Numeric Keys Execute Key Description Indicates the result of a bar code reading or other read operation.
10 Function Keys 11 IR Port 12 Power Contacts 13 14 CLR Key Fn Key 15 16 17 18 19 PC Card Slot USB Port Headset Jack Battery Pack Cover Lock Switches R Trigger Key 20 L Trigger Key 21 22 Wrist Strap Hole C-MOS Imager (C-MOS Imager models only) Reader Port (Laser Scanner models only) Reset Switch CF Card Slot Unit Terminal Battery Pack Cover 23 24 25 These keys can be assigned any function other than barcode reading. The following are the initial default settings.
1.3.2 DT-167CHGE Car Mounted Battery Charger Views Power Indicator Lamp Power Contacts Power Switch Car plug code jack Remove button Fig. 1.
1.3.3 DT-160IOE Bridge Satellite Cradle The following external views show the DT-160IOE Bridge Satellite Cradle. Refer to Table 1.5 for each referenced part on the DT-160IOE. Views Back 1 2 3 4 5 Top Right Bottom 13 6 14 7 12 8 Front 9 11 10 Fig 1.1 Table 1.5 No. 1 Names of parts Name USB Port 2 RS-232C Port 3 4 RS-422C Port AC Adaptor Jack Description This port accepts connection of a USB cable for connection to a computer for transfer of system data and file data.
No. 5 6 7 8 9 Name Wall Mount Unit Fastening Plate Terminal Detect Switch IR Port Power Contacts Power Indicator Lamp 10 Communication Indicator Lamp 11 System Status Indicator Lamp 12 13 Power Switch Desktop Unit 14 DIP Switches Description The holes in this plate accept screws that secure the wall mount unit in place. This switch detects when the Handheld Terminal is not seated correctly on the Bridge Satellite Cradle. This port transfers data to the Handheld Terminal via IR port.
1.3.4 DT-169CHGE Cradle-type Battery Charger The following external views show the DT-169CHGE (Cradle-type Battery Charger). Refer to Table 1.6 for each referenced part on the DT-169CHGE. Views 1 Back Front 2 5 Top Right Bottom 7 3 6 4 Fig 1.2 Table 1.6 No. 1 2 3 4 5 6 7 Names of parts Name AC Adaptor Jack Wall Mount Unit Fastening Plate Terminal Detect Switch Power Contact Power Indicator Lamp Power Switch Desktop Unit Description Connects the AC adaptor here.
1.3.5 DT-5022CHG Dual Battery Charger The following external views show the DT-5022CHG (Dual Battery Charger). Refer to Table 1.7 for each referenced part on the DT-5022CHG. Views Top 2 3 Front Back 3 1 1 4 4 4 4 3 Fig 1.3 Table 1.7 No. 1 2 3 4 Names of parts Name Charge Indicator Lamp AC Adaptor Jack Dual Battery Charger Connection Port Connection Bracket Attachment Holes Description This lamp indicates the charge status of the battery pack(s).
2. Hardware Specifications 2.1 DT-X11 Table 2.1 Item Specification Remark CPU, Memory CPU Intel® PXA255 Application Processor Operating clock; max 400 MHz RAM 64 MB FROM 128 MB (user area; approx. 115 MB) FlashFX built in. ® ® OS Microsoft Windows CE 5.0 operating system C-MOS Imager (DT-X11M30E, DT-X11M30U, and DT-X11M30RC) Method C-MOS Imager, 752 x 480 (Wide VGA), monochrome Emitting angle Redirected downward at 45 degree Resolution 1D : 0.15mm 2D Stacked : 0.169mm 2D Matrix : 0.33mm Composite : 0.
Laser Scanner (DT-X11M10E and DT-X11M10RC) Method Semi-conductor laser light Laser emitting angle Straight Wave length 650±10 nm Optical output <1 mW No. of scannings 100±20 times per second Resolution 0.127 mm (minimum) PCS 0.45 (minimum) Readable distance Approximately 40 to 300 mm Readable width Max. 40 mm Max. 238 mm Daylight for scanning Readable 1D bar code symbologies Display Display device No.
Bluetooth® Standard Comm. range Bluetooth® Specification Ver.1.2 Approx. 3 m Depending on the surrounding conditions Output power Maximum. 3dBm ( PowerClass 2) Serial interface Standard USB Slave Baud rate Full speed (12 Mbps) Audio Earphone jack φ2.5mm 3-pole PC Card (applicable to DT-X11M10E, DT-X11M30E, and DT-X11M30U) Standard PC Card Type I / Type II Supply current 450mA(5V), 500mA(3.3V) WLAN (applicable to DT-X11M10RC and DT-X11M30RC) Frequency category ISM Mini B 5 Pin. Supports headset. 3.3V/5.
2.2 DT-160IOE Bridge Satellite Cradle Table 2.2 Item Interface IrDA USB RS-232C Specification IrDA Ver. 1.1 compatible Half duplex Start/stop method 4 Mbps (maximum) USB Ver.1.1 compatible 12 Mbps (maximum) Standard Comm. method Synchronization Comm. speed Standard Baud rate Connector 1 2 4 3 1 2 3 4 VBus – Data (D -) + Data (D+) GND 1 2 3 4 VBus – Data (D -) + Data (D+) GND USB connector B type Full duplex Start/stop method 115.2 Kbps Comm. method Synchronization Comm.
Power Input from AC adaptor Charge/ supply power Input voltage Consumption current DC 12V ±5% Approx. 1,600 mA Plug AC adaptor Output voltage Output current Charge method EIAJ RC-5320A type 4 AD-S42120AE DC 5V ±10% 2,500mA(maximum) Constant voltage Charge time Approx. 2.5 hours Approx. 5.0 hours Power supply terminals Power supply terminals Table 2.3 GND When supplying power or transmitting data.
2.3 DT-167CHGE Car Mounted Battery Charger Table 2.4 Display Input Power Table 2.5 Item Specification Remark Status LED No. of LEDs 1 No. of display colors 2 In red and green Display content Power status (“POWER”) Indicates the status of terminal being mounted on the charger. OFF : Power is OFF. Flashing in green : Power is ON and the terminal is mounted on the Flashing in red charger. : Power is ON but the terminal is not mounted on the charger.
2.4 DT-169CHGE Cradle-type Battery Charger Table 2.6 Item Status LED No. of LEDs No. of display colors Display content Detection switch for DT-X11 terminal Input from Input voltage AC adaptor Consumption current Display Input Power Charge/Power supply Specification 1 2 Power status (“POWER”) Push switch DC 12V±5% Approx. 1,400 mA Plug AC adaptor Output voltage Output current Charge method EIAJ RC-5320A Class 4 AD-S42120AE DC5V±10% 2,500 mA (maximum) Constant voltage Charge time Approx. 2.
2.5 DIP Switch Setting for DT-160IOE The DIP switch is located on the rear side of Bridge Satellite Cradle. Change the ON/OFF settings according to your required system configuration. The new settings do not go into effect until the power switch is turned off and then back on. Fig. 2.1 Note: Other DIP switch settings are used for testing and inspection purposes Because of this, you must not use any DIP settings other than those described above.
2.6 Status Indication with LEDs Various operational statuses on the DT-160IOE can be displayed using the LEDs. The following table describes LED modes and their meanings. Table 2.8 Item Specification Remark DT-X11 terminal is not mounted DT-X11 terminal is mounted Power OFF Break of communication Communication is in progress Connection between cradle and PC is not valid.
2.7 DT-5022CHG Dual Battery Charger Basic Block Table 2.9 Item Specification Basic function Rechargeable battery pack HA-A20BAT DT-5025LBAT AC adaptor AD-S45150AU AD-S45150AE Remark Battery pack Large-capacity battery pack Dedicated batteries only. Input 100 to 230VAC (W/US power cord) Input 100 to 230VAC (W/European power cord) Dedicated AC adaptors for the charger Interface Block Table 2.
Charge output terminal CH1 PIN1: + PIN2: Charge output terminal CH2 PIN1: + PIN2: Input terminal DC jack 4.22V±30mV GND 4.22V±30mV GND Rated DC16V, input voltage DC 8.0 to 20.0V Battery Charge Block Table 2.12 Item Specification Charge control Output voltage DC 4.22V±30mV Charge current (standard mode) DC 1,600mA±10% Charge current (standby mode) DC 160±40mA Full charge detection current DC 120±30mA Voltage Full charge detection 4.1V control voltage Re-charge detection voltage 4.
Table 2.13 Weight/Dimensions Item Weight Dimensions Specification Approx.
2.8 HA-A20BAT/DT-5025LBAT Table 2.14 Item Rated capacity Rated voltage Discharge end voltage Standard charge current Charge voltage Charge hour (standard mode) Weight Dimensions Specification HA-A20BAT 1,700 mAh 3.7 V 2.75V 1.0 CA (=1.55A) 0 to 40 ºC 4.2±0.05V 2.5 DT-5025LBAT 3,400 mAh 3.7 V 2.75V 1.6A 0 to 50 ºC 4.2±0.05V 5.0 Approx. 45 g Approx. 37(W) x 57(L) x 13(H) mm Approx. 87 g Approx. 37 (W) x 57 (L) x 24 (H) mm 29 Remark 0.2C discharge 0.
2.9 DT-894CFU CF Card Extension Unit Fig. 2.2 Table 2.15 Dimensions/Weight Item Dimensions Weight Specification Approx. 70 (W) x 87 (D) x 13 (D) mm Approx. 85 (W) x 78 (D) x 13 (D) mm Approx. 40 g Approx.
3. Interfaces 3.1 DT-X11 CF Extension Slot Table 3.1 Interface Power voltage Supply current Specification CFA Rev.1.3 compatible 3.3V±5% 300 mA (maximum) Remark CF Type I/II 3.3V only Pin Assignment Table 3.
Table 3.3 IrDA interface Item Specification Communication speed, modulation Standard IrDA Ver. 1.1 compatible FIR 4 Mbps 4-value PPM modulation MIR 1.152 M, 576 Kbps NRZ modulation SIR 2.4 K to 115.2 Kbps NRZ modulation Emission unit Peak wave length 880 to 900 nm Emission strength Type 75 mW/sr Emission angle ±15° Reception unit Reception wave length 850 to 900 nm Incident illuminant SIR: 0.75 mW/cm2 or less FIR: 200 to 0.75, 0.33 to 0.
Memory backup battery Battery type Rated voltage Battery low warning Low main battery voltage Forcible OFF Low sub-battery voltage Button-shape Lithium rechargeable battery (CR-2032) 3.0 V VDET1: 3.4 V VDET2: 3.0 V VDETS: 2.3 V 33 Warning display, but still operable. Forcible OFF. Data cannot be retained.
4. Product Identification and Reference Numbers On the back of the DT-X11 and its options, there is a bar code and numbers printed on label as shown in Fig 4.1. This bar code is represented by 15 digits of Code128 symbology and by alphanumeric characters beneath the bar code. The numbers from 1 to 9 in the figure represent identification and references of each terminal. The numbers from 10 to 15 represent a manufacturing reference which is reserved by the manufacturer. See the figure below for each meaning.
5. Quality References This chapter will describe about references of the DT-X11 and its dedicated options concerned with environmental performance, compliance, mechanical and electric durability, etc. 5.1 Environmental Performances 5.1.1 DT-X11 Table 5.
5.1.3 DT-167CHGE Table 5.3 Item Specification Condition Temperature Operation Storage 0 ºC to 40 ºC -40 ºC to 85 ºC Humidity Operation Storage Storage in carton box Temperature Humidity 30 % to 80 %RH 30 % to 95 %RH -10 ºC to 50 ºC 30 % to 90 %RH No condensation No condensation 5.1.4 DT-5022CHG Table 5.4 Item Specification Condition Temperature Operation Non-operation 0 ºC to 40 ºC -10 ºC to 50 ºC Storage -10 ºC to 55 ºC When battery is not charged.
5.1.5 HA-A20BAT/DT-5025LBAT Table 5.5 Item Specification Condition Temperature Operation Non-operation 0 ºC to 40 ºC -5 ºC to 50 ºC Storage -10 ºC to 55 ºC When battery is not charged.
5.1.6 DT-894CFU Table 5.6 Item Specification Condition Temperature Operation Non-operation -20 ºC to 50 ºC -20 ºC to 70 ºC Humidity Operation Storage Storage in carton box Temperature Humidity Dust and water-splash proof 10 % to 80 %RH 5 % to 90 %RH -10 ºC to 55 ºC 90 %RH or less IP64 level (compliant with IEC60529) 38 No condensation No condensation All connectors are covered.
5.2 Electrical Performances 5.2.1 DT-X11 Table 5.7 Item Power consumption Anti-static strength Malfunction Destruction Specification DC2.5A/3.7 to 5.0V Remark ±6 KV ±12 KV 150 pF, 330ohm 5.2.2 DT-160IOE/DT-169CHGE Table 5.8 Item Current consumption Voltage Anti-static strength Malfunction Destruction Power interruption Line noise strength (Malfunction) Specification Approx. 0.1 A Approx. 1.6 A Remark When DT-X11 is not mounted on. While supplying power or transmitting data.
5.2.4 DT-5022CHG Table 5.10 Item Anti-static strength Malfunction Destruction Specification ±5 KV ±10 KV Remark - ESD method: 250 pF, 100 ohm - Probe: Finger type - Polarity: ± 5.2.5 HA-A20BAT/DT-5025LBAT Table 5.11 Item Anti-static strength Malfunction Destruction Specification ±5 KV ±10 KV Remark - ESD method: 250 pF, 100 ohm - Probe: Finger type - Polarity: ± 5.2.6 DT-894CFU CF Card Extension Unit Table 5.12 Item Power consumption Anti-static strength Malfunction Destruction Specification DC 0.
5.3 Mechanical Performances 5.3.1 DT-X11 Table 5.13 Item Specification Resistance to drop impact(height) In bare condition 120 cm In individual carton box In master carton box Resistance to vibration Condition Onto concrete, three times on each of the 6 sides and 4 corners. Onto concrete, one time on each of the 6 sides, 1 corner, 3 edges. 10 to 55 Hz, In X,Y, and Z directions Reciprocally for 30 minutes 70 cm or less 50 cm or less 0.15G or less 5.3.2 DT-160IOE/DT-169CHGE Table 5.
5.3.4 HA-A20BAT/DT-5025LBAT Table 5.16 Item Resistance to vibration Resistance to vibration (in carton box) Resistance to impact In bare condition In individual carton Specification 1G - 2G 75 cm 75 cm or less Condition 10 to 55 Hz, In X,Y, and Z directions Reciprocally for 15 minutes While the power is being turned off. 10 to 55 Hz, In X,Y, and Z directions Reciprocally for 15 minutes - 6 faces, 1 corner and 3 edges onto P tile. 5.3.5 DT-894CFU CF Card Extension Unit Table 5.
5.4 Reliability 5.4.1 DT-X11 Table 5.
5.4.3 DT-5022CHG Table 5.
5.5 Compliance 5.5.1 DT-X11 Table 5.21 Category Safety WLAN Type Approval Bluetooth Type Approval Laser Beam EMI EMS Bluetooth Logo DT-X11M30 U Yes No No Yes DT-X11M10E DT-X11M30E No Yes Yes No DT-X11M10RC DT-X11M30RC No Yes Yes No US EU CCC US No No Yes Yes Yes Yes EU China EN60825-1:1996 IEC60825 FCC part 15B EN301489-17 V1.1.1(09-2000) GB9245 GB17625.
6. Cable Specifications 6.1 For Chain Connection and Short Length Length; 1 meter or less Max. 1m Cable.(see Table 6.1) Modular plug compatible with 6/6-6 FR SYK50 by Sanyo Industrial Co. 1 2 3 4 5 6 1 2 3 4 5 6 Fig. 6.1 Table 6.1 Specifications of the cable Cable Core wire Sheath Characteristics Conductor Insulator Finish of external shape Insulator Finish of external shape Conductance resistance Insulation resistance 20/0.1A Semi-hard material P.V.C. 20/0.1A P.V.C. φ4.3±0.1mm 0.
6.2 For Chain Connection and Long Length Length; 1 meter or longer Max. 1,000m Cable compatible with SK-UTP 100M3P by Sanyo Industrial Co. Modular plug compatible with 6/6-6 FR SYK50 by Sanyo Industrial Co. 1 2 3 4 5 6 1 2 3 4 5 6 Fig. 6.3 Pin layout diagram of cable for chain connection and long distance (pin-to-pin straight/twist-pair connection) Wiring Cradle at lower position under the chain connection Pin no. 1 2 3 4 5 6 Signal IRS+ IRSISD+ ISDORD+ ORD- XXXXXXX XXXXXXX XXXXXXX Fig. 6.
7. Precautions 7.1 Handling Precautions for short-term storage (1 to 2 days period) • • If the DT-X11 is to be stored over holidays (including Saturday and Sunday), replace the HA-A20BAT (or DT-5025LBAT) battery pack with fully charged one before it is stored. This will conserve the memory backup battery and ensure retention of data on the DT-X11. If there is a possibility of the above or operator error (e.g.
7.2 Safety 7.2.1 Battery Pack/Memory Backup Battery Battery Pack • Never disassemble or retrofit the battery pack. The battery pack has safety mechanism and protection means incorporated to avoid hazards. Should they be damaged, the battery pack could become hot, generate smoke, explode, or ignite. • Never contact the “+” and “-“ terminals with a metal object such as wire. Also, do not carry or store the battery with a metal case.
• • The battery pack has a specific polarity. Do not force it into the DT-X11 when installing. Check the polarity. If the battery pack is connected backwards, it can be incorrectly charged and have an abnormal chemical reaction induced, causing it to become hot, smoke, explode, or ignite. If the internal electrolyte of the battery pack leaks and gets in your eye, do not rub the eye. Rinse the eye with a sufficient amount of clean water, such as tap water, then immediately consult with a medical doctor.
7.2.2 General • • • • • • • Avoid exposing it to water and foreign matter. Should foreign matter (metal chips, water, liquid chemicals) enter inside the DT-X11, immediately turn off it, remove the batteries, unplug the AC adaptor, then contact a CASIO distributor. Be aware of abnormal conditions. If the DT-X11 is continuously used in an abnormal condition, a fire or electric shock may occur.
