SERVICE MANUAL ELECTRONIC CASH REGISTER SE-S300/S2000 SE-C300/C2000 TE-900/1500 TK-950/1550 PCR-T48S/T470/T480/T470L/T480L/ T220S/T2100/T2200/T2100L/T2200L (EX-292/EX-293/EX-592/EX-593) FEB. 2008 SE-S2000M INDEX Ver.1 : Mar.
CONTENTS PAGE 1. SPECIFICATIONS ...................................................................................................... 1 2. MACHINE INITIALIZATION ....................................................................................... 4 3. DISASSEMBLY .......................................................................................................... 9 4. BLOCK DIAGRAM ................................................................................................... 17 5.
1. SPECIFICATIONS 1-1. Electrical specifications • Power consumption In operation Display off 120 V Max. 0.4 A Max. 0.05 A 230 V 240 V 0.26 A 0.04 A 0.26 A 0.04 A • Memory protection Back-up battery Back-up period Battery life Two new size AA alkaline batteries 1 year (25 °C) Replace the battery every 1 year. • Clock & Calendar Accuracy Auto calendar Within ± 30 sec. per month (25 °C) Effective until 2099 A.D. 1-2.
1-4. Drawer List Type Drawer Name Specification Europe UK U.S.A.
1-5. Option List DEVICE NAME MODEL NOTE Applicable Roll paper TRP-5880T Common Waterproof cover WT-89 SE-S300/S2000, TE-900/1500, PCR series Waterproof cover WT-90 SE-C300/C2000, TK-950/1550 Sheet cover WT-91 SE-C300/C2000, TK-950/1550 PC cable PRL-CB-2 Common External memory RAC-12B 4MB (Thermal pop) Common External memory RAC-14B 16MB (Electronic journal) Common CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
2.Initialization Initializing the cash register • Automatic initialization Use the following procedure to initialize the cash register before using it for first time after you purchase it. 1. Install the two memory backup batteries (see page 10 of the User’s Manual). 2. Plug the cash register into a wall outlet. • At this time, "00000000" appears on the display and the printer operates for a minite. Initialization is complete when the Printer stops operating.
Clearing a machine lock up If you make a mistake in operation, the cash register may lock up to avoid damage to programs and preset data. Should it happens, you can use the following procedure to clear the lock up without losing any data. 1. Power off the register. 2. Insert the PGM key in the mode switch. 3. SE-S300/SE-C300: Press down and hold FEED , and turn the mode switch to PGM mode. RECEIPT FEED , and turn the mode switch to PGM mode. SE-S2000/SE-C2000: Press down and hold 4.
2.Initialization Load IPL data • When you replace a main PCB with a spare parts, load the IPL data to ECR as the following steps; 1. Required materials RS232C cross cable which is using CV10 Memory pack RAC-12B RAC_TOOL software IPL data file *Please contact CASIO sales division to get the above materials. PC with RS232C COM port Windows 2000 / XP / Vista 2. System configuration RS232C Cross Cable SE series ECR RAC-12B PC with RS232C COM port Windows 2000/XP/Vista 3. Steps to load IPL data 3-1.
4) Plug in the power cord of ECR to the AC outlet and start up the diag software. (See Page 18) 5) Make double-click RAC_TOOL.exe to run the software. * RAC_TOOL.exe, FILE969.HAD, and LogoConv.dll (3 files) must be stored at same folder. 6) Select the appropriate COM port according to your configuration. 7) Select “Send RAC File” and choose the IPL file. The file name should be XXX.rac. (Do not send now) 8) Make sure the ECR is in the diag mode, then enter 914 and press "Sub Total" key.
12) The following transmission progress will be shown on the PC. 13) The following receipt will be issued when all the data has been received. (ECR will be terminated automatically if data is not receiving 5 second or more) RAC RAC END I PL 914 OK 914 This process will take approximately 20 minutes to send IPL data to the RAC-12B. * Please keep the special RAC memory pack for IPL, otherwise you need to do the above process again. 3-2. Send the IPL data from RAC to ECR.
3. DISASSEMBLY ■ Removing the upper case block 1. Remove the Printer cover. 2. Remove two Roll paper and theTake-up reel. Take-up reel Printer cover 3. Remove the battery cover and disengage the battery. 4. Remove 3 screws.
5. Lift the upper case block and then remove 3 FPCs. Hooks Hooks Hooks FPC (KEY) FPC (Pop-up displasy) Assembling Point: Be sure to insert the FPC securely by holding it with both hands or, if holding it with one hand, holding by its center.
■ Upper case block disassembly (KEY BOARD ASS'Y, MODE SW ASS'Y, POP-UP DISPLAY BLOCK) 1. Remove the FPC. 2. Remove 8 screws and then the KEY BOARD ASS’Y. FPC Assembling Point: Secure the FPC (Mode key, Pop-up Display). 3. Remove 15 screws and then disassemble the KEY BOARD ASS'Y.
4. Remove the screw and then the MODE SW ASS’Y. Screw 5. Remove the hook and then remove the STROBE ASSY Hooks 6. Remove the hook and then remove the STROBE ASSY. 7. Remove two FPCs and then remove the Rear Display Board.
■ Lower case block disassembly (Printer unit, MAIN PCB, LCD unit, E292-COM PCB) 1. Remove 4 screws. 2. Remove 2 FPCs and then 2 Printer units. Screws FPCs 3. Remove the FPC and 5 connectors. Drawer Battery Motor Power LCD Assembling Point: Run the power cable and the motor wires through the groove on the case.
4. Remove 3 screws. Screws 5. Loosen the screw and change the orientation of the plate. 6. Remove the main PCB. 7. Remove a screw.
8. Remove the hook and then remove the LCD ASSY. 9. Remove 2 screws and then the LCD and E292LCD-E2 PCB. Screws 10. Unsolder to remove 3 lead wires. 11. Remove the FPC and then the E292LCD-E2 PCB.
12. Remove 2 screws and then the Lower case unit ans AC Adaptor. Lower case unit Screws Drawer AC Adaptor 13. Remove 3 screws and then the Lower case unit ans AC Adaptor. Screws 14. Remove 2 screws and then the Motor assy. Motor assy Screws 15. Remove 4 screws and then the E292-COM PCB.
4.
5. DIAGNOSTIC OPERATION 5-1. To start the diagnostic program 1. First, be sure that MODE KEY is “OFF”. While holding down the “JFEED” button, turn MODE KEY to “PGM”. When the “JFEED” button is released, the main display indicates as illustrated below. INIT T1 RPT T2 T3 T4 TOTAL CHANGE AMOUNT 2. Enter “99990000” and then press the “SUB TOTAL” button. INIT , RPT , T1 T2 T3 T4 TOTAL CHANGE AMOUNT 3. After DIAG version is printed out, DIAG mode starts.
5-3. Displaying the status of the device [Function] Changing to status mode or pressing the “C” key when the device is in the command input wait state during test program startup displays the device status. [DISPLAY] The figure below shows the relative display positions for the status information.
5-4. Check item The following test can be checked in the diagnostic test.
5-5. Operation of each test [ 1 ] BATCH TEST 1 [Function] RAM READ/WRITE test, Watch, buzzer test and drawer open test are performed continuously. [Operation] Operation : 1 SUB TOTAL The following tests are performed automatically. (1) RAM test: WRITE/READ area test. (2) Test print (3) Time setting: Set the following data. Arranged data: 2005 December 31,23:59'30 (4) Buzzer: Ring once the one shot buzzer. No print or display in this test. (5) Drawer open: Drawer 1 opens only.
[ 3 ] RAM WRITE/READ TEST [Function] Data on the RAM is written, and tests are performed to check if the data has been written properly. The data to be written should be a one-byte data, which is the sum of the fourth, the third, and the second digits from the last of the address. After writing is completed, the data is read and checked whether it is identical to the original. The test will not be performed, however, in the area where performing this test affects the operation.
[ 5 ] FLASH ROM CLEAR TEST [Function] After this test, be sure to perform [6] FLASH ROM WRITE/READ test before conducting other tests. If other tests are performed without having conducted FLASH ROM WRITE/READ test and the program is damaged, proper operation cannot be guaranteed. Please perform IPL again.
[ 7 ] FLASH ROM CLEAR & WRITE/READ TEST [Function] After CLEAR function clears the memory, WRITE test is performed. [Operation] Operation : n n: 3 1 2 SUB TOTAL 0 = One time check (can be omitted) not 0 = Continuous check (To stop the test, press “C” key) [Display] A counter is displayed in the 7 segments to indicate that RAM check is in progress. [Print] The following is printed when all areas for RAM are tested.
[ 9 ] DISPLAY TEST [Function] The test of LCD/7 segment display and transaction display is performed as shown below.
[ 10 ] DISPLAY TEST (REPEAT) [Function] The test of LCD/7 segment display and transaction display is performed as shown below. Pattern 1 RPT Pattern 2 T1 T2 T3 T4 TOTAL CHANGE RPT AMOUNT Pattern 3 T1 T2 T3 T4 TOTAL CHANGE AMOUNT [Operation] Operation : 5 2 1 SUB TOTAL To stop the test, press “C” key [Print] D I SP D I SP ND 521 OK 521 [ 11 ] 7 SEGMENT DISPLAY TEST [Function] The test of 7 segment display is performed as shown below.
[ 12 ] LCD BACKLIGHT TEST [Function] LCD Backlight is turned ON/OFF. [Operation] Operation : c c: 0 1 2 1 SUB TOTAL 0 = Press any button to turn “OFF” -> “ON” 1 = Backlight OFF 2 = Backlight ON [Print] D I SP D I SP ND L I GH T 121 OK 121 [ 13 ] DISPLAY PATTERN TEST [Function] Performs an LCD display pattern test. The test displays the 4 patterns shown below. In run-once mode, press any key to end the test. In unlimited-run mode, set the mode to OFF to end the test.
[ 14 ] LCD CONTRAST ADJUSTMENT TEST [Function] Adjusts the LCD contrast and writes the adjustment to the FLASH ROM. Up to 16 adjustments can be written to the FLASH ROM. If more than 16 adjustments are written, an error occurs. The contrast value when adjustment begins is the value written during the previous adjustment ("22" if no data has been written). After the adjustment, pressing the “#1” key updates the stored adjustment value.
[ 15 ] LCD BIT MAP TEST [Function] Performs an LCD display pattern test. Command input Pattern 1 Pattern 4 Press Any key Pattern 1 RPT Pattern 2 T1 T2 T3 T4 TOTAL CHANGE RPT T1 T2 T3 T4 TOTAL CHANGE RPT AMOUNT 1 SUB TOTAL To stop the test, press “C” key.
[ 16 ] INTERNAL PRINTER CHARACTER PRINT TEST [FUNCTION] This test will check the characters in the receipt/journal of the internal printer. [Operation] Operation : a a: c: n: d: c n 0 3 d SUB TOTAL 0 = normal print out 1 = reduced size print out 0 = prints character’ B’ 1 = prints all characters 0 = One time check not 0 = Continuous check (To stop the test, press “C” key) 3 = Recipet 4 = Journal 5 = Recipet and Journal [Print] 1. Prints character’ B’ BBBBBBBBBBBBBBBB 2.
[ 17 ] INTERNAL PRINTER GRAPHIC PATTERN PRINT TEST [FUNCTION] This test will check the graphic patterns in the receipt/journal of the internal printer.
[ 18 ] INTERNAL PRINTER DOT RATE TEST [FUNCTION] This test will check the printing of the receipt/journal according to the following specifications. The printing specification is reflected in 1/2 line and the only specified number of dot lines are printed in all dots from the 1 dot line. Note that 1/2 line is printed two times because the printing unit is one line.
[ 19 ] INTERNAL PRINTER PRINT TEST [FUNCTION] Print out is performed on the internal printer receipt/journal in the following format. This test is performed once. The number of the tests to be performed cannot be changed. [Operation] Operation : 4 3 5 SUB TOTAL [Print] PRT 435 Prints 3 lines from character code 0X30 to 0X8. ND 435 [ 20 ] RS232C PORT TEST [FUNCTION] This is the RS232C test. The loop back test for RS232C port is performed by making the connection shown in the figure.
[ 21 ] RS232C PORT BATCH TEST [Function] This is the RS232C port batch test. When performing this test, fix loop back connectors to all COM ports. By the setting below, the loop back batch test is performed once from COM1 through COM2. [Operation] Operation : 4 Baud rate: Check time: 0 SUB TOTAL COM1: 19.
[ 22 ] TIME SETTING [ 23 ] TIME DISPLAY [Function] This sets the time and date. When setting the time, the time and date will be displayed without inputting the fixed value.
[ 24 ] DRAWER OPEN TEST [Function] This test checks whether the drawer opens or not.. [Operation] Operation : n n: 0 9 1 SUB TOTAL 0 = One time check not 0 = Continuous check (To stop the test, press “C” key) [Print] D RW D RW END 91 OK 91 [ 25 ] BUZZER TEST [FUNCTION] This test checks whether the buzzer sounds or not. One time check causes one shot buzzer to sound once, while infinite time check causes the buzzer to sound for 500 msec.
[ 26 ] KEY DISPLAY TEST [FUNCTION] The hard key code of a key is displayed every time any key except “C” key is pressed. The hard key code is arranged as follows.
[ 27 ] OBR TEST [Function] This is a scanner test. The test enters the wait mode for the scanner input, and waits only for scanner. The test determines the result between OK and NG by comparing the fixed data and the read data. * The fixed barcode is as follows. [Operation] SE-S2000/SE-C2000: COM2 SE-S300/SE-C300: COM1 Operation : 9 5 CA/AMT TEND To stop the test, press “C” key [Print] OBR OBR OBR END ERR 95 OK * * * * * * * * When an error occurs, the read data is printed.
6. ERROR CODE LIST This section describes what to do when you have problems with operation. When an error occurs Errors are indicated by an error codes. When this happens, you can usually find out what the problem is as illustrated below. Press C and check the appropriate section of this manual for the operation you want to perform.
Error code E040 Issue guest receipt E046 E049 REG buffer full CHECK memory full E050 DETAIL memory full E051 CHK/TBL No. is occupied E053 CHK/TBL No. is not opened E075 E146 E200 E201 E202 Negative balance cannot be finalized PLU maintenance file full. Press <#2> to exit PLU Code is not exist.
7.
MAIN PCB (E292-1 PCB) (BOTTOM VIEW) — 42 —
8. CIRCUIT DIAGRAMS SE series SE-S300/SE-S2000/SE-C300/SE-C2000 TE series / TK series TE-900/TE-1500/TK-950/TK-1550 PCR series PCR-T48S/PCR-T470/PCR-T480/PCR-T470L/PCR-T480L PCR-T220S/PCR-T2100/PCR-T2200/PCR-T2100L/PCR-T2200L (EX-292/EX-293/EX-592/EX-593) 1. MAIN PCB CIRCUIT 1-1. MAIN PCB CIRCUIT 1/5 (PW,PWD,COM) ........................................................................44 1-2. MAIN PCB CIRCUIT 2/5 (CPU) ........................................................................................
SE-S300 and SE-C300: not used SE-S300: not used CASIO COMPUTER CO.,LTD. — 44 — Model SE-S300/S2000/C300/C2000 Board No. Name Drawing No.
SW1, R234, C112: not used CASIO COMPUTER CO.,LTD. — 45 — Model SE-S300/S2000/C300/C2000 Board No. Name E292-1 MAIN BOARD 2/5 (CPU) Drawing No.
R233: not used CASIO COMPUTER CO.,LTD. — 46 — Model SE-S300/S2000/C300/C2000 Board No. Name Drawing No.
CASIO COMPUTER CO.,LTD. — 47 — Model SE-S300/S2000/C300/C2000 Board No. Name E292-1 MAIN BOARD 4/5 (LCD, KEY, LED) Drawing No.
R173:SE-S300 not used SE-S300: not used SE-S300: not used R219,220,221,222:SE-S2000 not used SE-S300: not used SE-S300/C300 only SE-S2000: not used SE-S2000/C2000 only SE-S300: not used R223,224,225,226,227,228:SE-S2000 not used IC22,C75,R184:SE-S300 not used SE-S300: not used CASIO COMPUTER CO.,LTD. — 48 — Model SE-S300/S2000/C300/C2000 Board No. Name E292-1 MAIN BOARD 5/5 (PRT) Drawing No.
SE-S2000/SE-C2000 only CASIO COMPUTER CO.,LTD. — 49 — Model SE-S300/S2000/C300/C2000 Board No. E283-E22 Name CON BOARD Drawing No.
-9.5V VCC PA-B TP24 L1 CDRH3D16NP-220NC 1 2 C1 D1 1u VLCD RB161M-20TR 5 Vin FB 2 3 C29 GND C30 0 S-817A30ANB R5 J3 R4 C4 2 VSS NC 4 TP4 1MF Q2 TP5 TP6 TP7 TP8 TP9 CN2 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 J2 0 C10 1u 0 C9 510K V3.0 1u 510K R9 C8 R8 1u 1.5MF C7 R7 1u 2MF C6 J6 R6 1u DTD113ZK 3 510K BM04B-SRSS 33u/10V 3 3 DTA115EUA VO VIN 1 R3 4 2 510K Cathode 2 Q1 4 0.022u C26 3 IC2 0.
CN2 IMSA-9610S-12B-TC 1 SDP1 2 SB0 3 SF0 4 SA0 5 SC0 6 SD0 7 SDP0 8 SE0 9 SG0 10 DG0 11 DG1 12 STR D6 HLMP-S501 DG1 D7 HLMP-S501 1 2 3 4 5 6 7 8 9 HDSP-521G e1 d1 c1 DP1 e2 d2 g2 c2 DP2 f1 g1 a1 b1 DI1 DI2 f2 a2 b2 D1 f1 g1 a1 b1 DI1 DI2 f2 a2 b2 18 17 16 15 14 13 12 11 10 DG0 18 17 16 15 14 13 12 11 10 HDSP-521G e1 d1 c1 DP1 e2 d2 g2 c2 DP2 D2 1 2 3 4 5 6 7 8 9 f1 g1 a1 b1 DI1 DI2 f2 a2 b2 1 2 3 4 5 6 7 8 9 HDSP-521G e1 d1 c1 DP1 e2 d2 g2 c2 DP2 f1 g1 a1 b1 DI1 DI2 f2 a2 b2 D3 1 2 3
9. PARTS LIST SE series SE-S300/SE-S2000/SE-C300/SE-C2000 TE series / TK series TE-900/TE-1500/TK-950/TK-1550 PCR series PCR-T48S/PCR-T470/PCR-T480/PCR-T470L/PCR-T480L PCR-T220S/PCR-T2100/PCR-T2200/PCR-T2100L/PCR-T2200L (EX-292/EX-293/EX-592/EX-593) EXPLODED VIEW BODY ............................................................................................................53 BUTTON BLOCK (STROKE) ........................................................................54 BUTTON BLOCK (COMBINATION) .......
EXPLODED VIEW (BODY) 98 72 69 71 8 6 70 7 5 63 4 66 64 68 SE-S2000/SE-C2000/TE-1500/TK-1550/ PCR-T220S/2100/2100L/2200/2200L SE-S300/SE-C300/ TE-900/TK-950/ PCR-T48S/470/470L/480/480L 94 93 92 91 92 65 67 100 94 91 96 92 68 95 91 76 76 84 84 3 2 1 87 79 77 86 83 80 82 78 81 75 89 91 90 74 88 73 85 101 99 103 — 53 — 102
BUTTON BLOCK (STROKE) SE-S300/SE-S2000/TE-900/TE-1500/PCR series 22 10 to 21 23 24 25 26 27 28 9 29 31 30 32 33 34 — 54 —
BUTTON BLOCK (COMBINATION) SE-C300/SE-C2000/TK-950/TK-1550 48 49 48 36 ~ 47 35 61 51 50 52 62 36 ~ 47 54 53 59 55 58 58 56 60 57 — 55 —
1 2 3 4 SE-S300 SE-S2000 SE-C300 SE-C2000 N Item Code No. 1.
1 2 3 4 SE-S300 SE-S2000 SE-C300 SE-C2000 N Item Code No. Parts Name 3.CUSTOMER DISPLAY BLOCK 4 10272394 CASE/REAR DISPLAY 5 10272398 PANEL/REAR DISPLAY 6 10275915 CABLE/FFC JOINER 7 10275916 CABLE/FFC JOINER 8 10275677 PCB ASSY/E283-E22 D1,D2,D3,D4 10072597 LED/7SEG 4.
1 2 3 4 SE-S300 SE-S2000 SE-C300 SE-C2000 N Item Code No. 55 10276640 56 10276638 57 10276642 58 10166869 59 10276641 60 10276643 61 10276743 62 10276740 6.UPPER CASE BLOCK 63 10294951 63 10294958 63 10294885 63 10294894 64 10269751 64 10276416 65 10072504 66 10291888 67 10242021 68 10242022 69 10236319 70 10284497 71 10284495 72 10291886 72 10294959 72 10294886 72 10294887 7.
1 2 3 4 SE-S300 SE-S2000 SE-C300 SE-C2000 N Item 9.PRINTER BLOCK 92 93 94 95 96 97 98 98 10.OTHERS 99 100 101 102 103 Code No.
1 2 3 4 N TE-900 TE-1500 TK-950 TK-1550 Item Code No. 1.
1 2 3 4 N TE-900 TE-1500 TK-950 TK-1550 Item Code No. Parts Name 3.CUSTOMER DISPLAY BLOCK 4 10272394 CASE/REAR DISPLAY 5 10272398 PANEL/REAR DISPLAY 6 10275915 CABLE/FFC JOINER 7 10275916 CABLE/FFC JOINER 8 10275677 PCB ASSY/E283-E22 D1,D2,D3,D4 10072597 LED/7SEG 4.
1 2 3 4 N TE-900 TE-1500 TK-950 TK-1550 Item Code No. 54 10276639 55 10276640 56 10276638 57 10276642 58 10166869 59 10276641 60 10276643 61 10276743 62 10276740 6.UPPER CASE BLOCK 63 10294954 63 10294882 63 10294885 63 10294894 64 10276416 65 10072504 66 10291888 67 10242021 68 10242022 69 10236319 70 10284497 71 10284495 72 10295911 72 10295913 72 10295914 72 10295916 7.
1 2 3 4 N TE-900 TE-1500 TK-950 TK-1550 Item 9.PRINTER BLOCK 92 93 94 95 96 97 98 10.OTHERS 99 100 101 102 103 Code No.
1 2 3 4 5 N PCR-T48S PCR-T470 PCR-T480 PCR-T470L PCR-T480L Item 6 7 8 9 10 Code No. Parts Name 1.
1 2 3 4 5 N PCR-T48S PCR-T470 PCR-T480 PCR-T470L PCR-T480L Item 6 7 8 9 10 Code No. Parts Name 3.CUSTOMER DISPLAY BLOCK 4 10272394 CASE/REAR DISPLAY 5 10272398 PANEL/REAR DISPLAY 6 10275915 CABLE/FFC JOINER 7 10275916 CABLE/FFC JOINER 8 10275677 PCB ASSY/E283-E22 D1,D2,D3,D4 10072597 LED/7SEG 4.
1 2 3 4 5 N PCR-T48S PCR-T470 PCR-T480 PCR-T470L PCR-T480L Item 6 7 8 9 10 Code No. 5.UPPER CASE BLOCK 63 10294951 63 10294954 63 10294958 63 10294882 64 10269751 64 10276416 65 10072504 66 10291888 67 10242021 68 10242022 69 10236319 70 10284497 71 10284495 72 10291887 72 10294955 72 10294962 72 10294883 72 10300548 72 10300550 6.
1 2 3 4 5 N PCR-T48S PCR-T470 PCR-T480 PCR-T470L PCR-T480L Item 8.PRINTER BLOCK 92 93 94 95 96 97 98 98 9.OTHERS 99 100 101 102 103 6 7 8 9 10 Code No.
DRAWER S type DL-1331/DL-1332/DL-1842 2 1 13 15 5 4 14 10 9 8 7 3 18 16 19 6 11 11 6 11 17 12 20 — 68 —
1 DL-1331 2 DL-1332 3 DL-1842 N Item 1 1 2 2 3 3 4 5 6 7 8 9 10 11 12 13 14 15 15 16 17 18 19 20 Code No.
DRAWER M type DL-2800/DL-2801/DL-2802/DL-2803/DL-2804/DL-2805/DL-2806/DL-2807/DL-2432/DL-2433 DL-2800/DL-2803/DL-2806/DL-2807 13 DL-2432/DL-2433 14 DL-2801/DL-2802/DL-2804/DL-2805 13 12 14 12 13 14 12 18 18 18 15 15 17 15 17 16 16 1 3 7 11 5 2 19 4 8 5 20 — 70 — 6 10 9
1 2 3 4 5 6 7 8 9 10 DL-2800 DL-2801 DL-2802 DL-2803 DL-2804 DL-2805 DL-2806 DL-2807 DL-2432 DL-2433 N Item Code No.
CASIO COMPUTER CO.,LTD.