user manual

ManualsBrandsCasio ManualsGrillXJ-S46

Contents

E-1

English

Safety Precautions .....................................E-2

Operating Precautions...............................E-6

Lamp Handling Precautions ......................E-6

Lamp Replacement Precautions ............... E-6

Other Precautions .....................................E-7

Unpacking ...................................................E-9

Using the User Documentation on the

CD-ROM....................................................E-9

Projector Features and Main Functions

...E-10

General Guide...........................................E-10

Remote Controller General Guide...........E-12

Preparing the Remote Controller.............E-12

Replacing the Remote Controller Battery

...E-13

Getting Ready ...........................................E-14

Setting Up the Projector .......................... E-14

Setup Precautions ................................... E-15

Adjusting the Projector Elevation Angle

.... E-16

Rear Projection

(From the Back of the Screen) ................ E-16

Connecting a Computer to the Projector

.... E-17

Connecting to a Standard Video Device

.... E-17

Connecting to a Component Video

Output Device.......................................... E-18

Connecting a USB Device to the

Projector (XJ-S36/XJ-S46 Only).............. E-19

Turning On the Projector ......................... E-20

Turning Off the Projector ......................... E-22

Projector Basics .......................................E-23

Selecting the Input Source ...................... E-23

Adjusting the Projected Image ................ E-23

Adjusting the Volume Level..................... E-24

Keystone Correction (KEYSTONE).........E-25

Using the Setup Menu..............................E-26

User Maintenance.....................................E-27

Cleaning the Projector............................. E-27

Reattaching the Lens Cover.................... E-28

Replacing the Lamp ................................ E-29

Troubleshooting .......................................E-34

Indicators................................................. E-34

Projector Troubleshooting ....................... E-38

Specifications ...........................................E-40

• DLP is a registered trademark of Texas Instruments Incorporated of the United States.

• Microsoft, Windows, Windows NT, Windows Vista, and PowerPoint are registered trademarks or

trademarks of Microsoft Corporation in the United States and other countries.

• Apple and Macintosh are registered trademarks of Apple Inc. of the United States.

• Adobe and Reader are registered trademarks of Adobe Systems Incorporated.

• XGA is a registered trademark of IBM Corporation of the United States.

• Other company and product names may be registered trademarks or trademarks of their

respective owners.

• The contents of this User’s Guide are subject to change without notice.

• Copying of this manual, either in part or its entirety, is forbidden. You are allowed to use this

manual for your own personal use. Any other use is forbidden without the permission of CASIO

COMPUTER CO., LTD.

• CASIO COMPUTER CO., LTD. shall not be held liable for any lost profits or claims from third

parties arising out of the use of this product or this manual.

• CASIO COMPUTER CO., LTD. shall not be held liable for any loss or lost profits due to loss of

data caused by malfunction or maintenance of this product, or any other reason.

• The sample screens shown in this manual are for illustrative purposes only, and appear

differently from the screens actually produced by the product.

User’s Guide (Basic Operations)

• Be sure to read the “Safety Precautions” on page E-2 and “Operating Precautions” on page

E-6 before trying to use this projector.

• This manual covers only basic operations, including how to set up the projector, basic projector

operations, and how to replace the lamp. For more detailed information, see the User’s Guide

(UsersGuide_English.pdf) on the CD-ROM that comes with the projector.

Summary of content (40 pages)

PAGE 1
User’s Guide (Basic Operations) • Be sure to read the “Safety Precautions” on page E-2 and “Operating Precautions” on page E-6 before trying to use this projector. • This manual covers only basic operations, including how to set up the projector, basic projector operations, and how to replace the lamp. For more detailed information, see the User’s Guide (UsersGuide_English.pdf) on the CD-ROM that comes with the projector. Contents Safety Precautions .....................................
PAGE 2
Safety Precautions Thank you for selecting this CASIO product. Be sure to read these “Safety Precautions” before trying to use it. After reading this User’s Guide, keep it in a safe place for future reference. About safety symbols Various symbols are used in this User’s Guide and on the product itself to ensure safe use, and to protect you and others against the risk of injury and against material damage. The meaning of each of the symbols is explained below.
PAGE 3
Safety Precautions ● Looking into the lens or vents while lamp is on Never look directly into the lens or vents while lamp is on. The strong light emitted by the projector creates the risk of eye damage. ● Blocking the vents ● Water and foreign matter Never allow water to get on the projector. Water creates the risk of fire and electric shock. Never place a vase or any other container of water on top of the projector. Water creates the risk of fire and electric shock. 1. 2. 3.
PAGE 4
Safety Precautions ● Location Never locate the projector in any of the following types of locations. Doing so creates the risk of fire and electric shock. • Near an area subject to strong vibration • An area subject to large amounts of moisture or dust • In a kitchen or other area exposed to oil smoke • Near a heater, on a heated carpet, or in an area exposed to direct sunlight • An area subject to temperature extremes (Operating temperature range is 5°C to 35°C (41°F to 95°F)).
PAGE 5
Safety Precautions ● Button battery Caution Misuse of a battery can cause it to leak and stain the area around it, or to explode, creating the risk of fire and personal injury. Make sure that you always observe the following precaution. • Use only the type of battery that is specified for the remote controller. ● Dead battery Be sure to remove the battery from the remote controller as soon as it goes dead. • Remove the battery from the remote controller if you do not plan to use it for a long time.
PAGE 6
Operating Precautions Lamp Handling Precautions Caution Continued use of a lamp that has passed its lamp life increases the risk of the lamp rupturing. Replace the lamp with a new one as soon as possible after the replacement message appears. z Never touch the glass of the lamp with your fingers. Doing so can damage the lamp and shorten its life. z The light source lamp is a consumable item. The average life of a lamp is approximately 2000 hours.
PAGE 7
Operating Precautions This projector is made of precision components. Failure to observe the following precautions can result in inability to correctly save data and malfunction. ● Never use or store the projector in the following locations. Doing so creates the risk of malfunction of and damage to the projector.
PAGE 8
Operating Precautions ● Even if your projector is still within the warranty period, you will be charged for repair if a problem is due to running the projector non-stop for very long periods (like 24 hours) or if the projector was set up and used without following the “Setup Precautions” on page E-15 of this manual.
PAGE 9
Unpacking English As you unpack the projector, check to make sure that all of the items listed below are present. • • • • • • DATA PROJECTOR Remote Controller (YT-35) Test Battery (CR2025) (Loaded in remote controller.
PAGE 10
Projector Features and Main Functions z Slim and compact: B5 file size and a mere 32 mm slim (at thinnest part). Compact enough to install or use just about anywhere. z Wide projection range, from a minimum of 0.84 meters: Wide angle 2X zoom allows projection even when projector-to-screen distance is severely limited. Minimum projection distance is 1.7 meters, even when projecting onto a 60-inch large screen.
PAGE 11
Warning z Never look into the lens while the projector is turned on. z Never allow the intake and exhaust vents to become blocked, and make sure there is at least 30 cm (11.8 inches) clearance around the projector. Blocked vents can cause heat to build up, creating the risk of fire and malfunction. z Never touch the areas around the exhaust vents. These areas can become very hot, and create the risk of burn injury.
PAGE 12
General Guide Remote Controller General Guide [INPUT] key Remote control signal emitter [AUTO] key CLASS 1 LED PRODUCT [ ] (Power) key [BLANK] key [ZOOM +] [ZOOM –] keys [FREEZE] key [FOCUS [FOCUS [VOLUME] key ] ] keys [COLOR MODE] key [D-ZOOM +] [D-ZOOM –] keys [MENU] key [KEYSTONE +] [KEYSTONE –] keys Cursor keys [POINTER] key [BRIGHT] key ([ [ECO] key ([ ] key) [ENTER] key ([STYLE] key) ] key) [ASPECT] key ([ [ESC] key ] key) [FUNC] key Preparing the Remote Controller The remote
PAGE 13
General Guide Before you can use the remote controller for the first time, you need to load the battery that comes with it. 1. Caution RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Caution Misuse of a battery can cause it to leak and stain the area around it, or to explode, creating the risk of fire and personal injury. Make sure that you always observe the following precautions.
PAGE 14
Getting Ready Setting Up the Projector Locate the projector on a desk, table, or stand that is firm and level. Make sure to allow sufficient space around the sides and back of the projector for proper ventilation. z The following illustrations show how the projector should be oriented for optimum projection relative to the screen. Viewed from Above Viewed from the Side Screen Screen The center of the projector’s lens should be aligned with the horizontal center of the screen.
PAGE 15
Getting Ready Note that the condition of the environment where you use the projector greatly affects its performance. Make sure that the following are the conditions of projector setup whenever you use it. z Use a conveniently located power outlet that you can reach easily when you need to unplug the projector. z Do not place any objects within the area indicated by the dashed line in the illustration below. Be especially careful that you never block intake and exhaust vents.
PAGE 16
Getting Ready Adjusting the Projector Elevation Angle You can change the elevation angle of the projector in a range of 0 to 12 degrees. You can also make fine adjustments to the left and right side elevation angle when necessary. To change the projector elevation angle 1. Lift up the front of the projector and press the release button. z This causes the elevation adjustment foot to drop from the bottom of the projector.
PAGE 17
Getting Ready Connecting a Computer to the Projector English You can use the projector to project an image of video output from a computer. z Always turn off the projector and the computer before connecting them. z Take care so the volume level of the computer is not set too high.
PAGE 18
Getting Ready Connecting to a Component Video Output Device Some video devices are equipped with a component video output terminal. You can use an optionally available component video cable (YK-3) to connect the RGB input terminal of the projector to the component video output terminal of a video device. z Always turn off the projector and the video device before connecting them.
PAGE 19
Getting Ready If you have an XJ-S36/XJ-S46 model projector, you can connect any of the following USB devices to the projector’s USB port. z USB Memory Device You can transfer image and movie data from your computer to a USB memory device* and take it along with you for projection with the XJ-S36/XJ-S46. The projector comes with software that converts Microsoft PowerPoint sheets to images, which you can then store to a USB memory device.
PAGE 20
Getting Ready Turning On the Projector Before performing any of the operations in this section, make sure you first set up the projector and connect to an output device. AC Power Cord Precautions z Use the AC power cord that comes with the projector. z Make sure that you use a power source with the same voltage as that specified for the projector. z Do not share the outlet supplying power to the projector with other devices.
PAGE 21
z If the Eco Mode is turned on, the LAMP indicator will light green when warm up starts. z If the projector is hot when you plug the AC power cord into a power outlet, it will go into a cool down state. The cool down state is indicated by the POWER/STANDBY indicator flashing orange. Note that the projector will not turn on until cool down is complete, even if you press the [ ] (power) key. The projector will turn on and enter the standby state after cool down is complete.
PAGE 22
Getting Ready Turning Off the Projector z When you turn off the projector, the lamp goes out and the projector goes into a cool down state. Note that you will not be able to turn the projector back on again while it is cooling down. z The projector may remain quite hot for a while after you turn it off. Take care when moving the projector or otherwise handling it after use. See “Precaution when Handling the Projector after Use” (page E-8) for more information.
PAGE 23
z For detailed information about projection operations, see the User’s Guide on the CD-ROM that comes with the projector. z For details about connecting USB devices to the XJ-S36/XJ-S46 projector and procedures you need to perform to project images from a USB device, see “USB Function Guide” on the bundled CD-ROM. Selecting the Input Source When you turn on the projector, it first checks the RGB terminal for an input signal and then the VIDEO terminal.
PAGE 24
Projector Basics Adjusting the Volume Level You can use the remote controller keys to adjust the volume level of the audio that is output from the projector’s speaker. To adjust the volume level 1. On the remote controller, press the [VOLUME] key. 2. 3. Press the [ ] key to increase the volume, or the [ ] key to lower the volume. z This causes the [Volume] screen to appear on the projected image. After the setting is the way you want, press the [ESC] key.
PAGE 25
Projector Basics When the projector is at an angle to the screen it is projecting on, the projected image may have different length top and bottom edges. This phenomenon is called, “keystoning”. This projector comes with functions for automatic as well as manual keystone correction, which provides a regularly shaped projected image. z Keystone correction can cause the corrected image to be smaller than the original (uncorrected) image, or it can cause distortion of the image.
PAGE 26
Using the Setup Menu Pressing the [MENU] key while an image is being projected displays the setup menu on the projected image. The setup menu can be used to configure a variety of different projector settings. Use the cursor keys to select and configure settings, and the [ENTER] key to register them. The menu items that can be set (or displayed) depend on the current input source.
PAGE 27
User Maintenance Cleaning the Projector z Always make sure that the projector has cooled sufficiently before cleaning it. If the projector is turned on, perform the following steps before cleaning it. 1. 2. 3. Turn off the projector. Check to make sure that the POWER/STANDBY indicator has changed to amber. Unplug the power cord from the power outlet, and allow the projector to cool down for about 60 minutes.
PAGE 28
User Maintenance Reattaching the Lens Cover Use the following procedure to replace the lens cover if it should accidentally become detached from the projector. 1. Insert the nub (3) of the left tab of the lens cover into the depression (1) of the tab under the lens. z When performing the above step, make sure that the lens cover is open to 90 degrees in relation to the front of the Data Projector. 2.
PAGE 29
User Maintenance Caution z Continued use of a lamp that has passed its lamp life increases the risk of the lamp rupturing. Replace the lamp with a new one as soon as possible after the replacement message appears. z The light source lamp is a consumable item. The average life of a lamp is approximately 2000 hours. After 2000 hours, a message appears to alert you to the need of lamp replacement.
PAGE 30
User Maintenance Replacing the Lamp z During normal use, the lamp and the area around it become extremely hot. Before replacing the lamp, turn off the projector and wait for the cool down operation (indicated when the POWER/STANDBY indicator is flashing amber) to finish. Next, disconnect the AC power cord from the projector, and wait for at least 60 minutes to allow it to cool down even further.
PAGE 31
User Maintenance There are two types of lamp cartridges, Type A (with handle) and Type B (with ribbon) as shown in the illustration. Note that the handle and the ribbon serve exactly the same function, so you can perform the following procedures the same way, regardless of whether your lamp cartridge has a handle or a ribbon. All of the illustrations in this manual show the Type B lamp cartridge. A B z Disposing of the Lamp (U.S.A. Only) This product utilizes a lamp containing mercury.
PAGE 32
User Maintenance 5. Loosen the three screws indicated by an mark. 7. Insert the new lamp cartridge as far as it will go, as shown in the illustration. z After inserting the lamp cartridge, in the case of a Type A lamp cartridge, lower the handle towards the lamp. For a Type B lamp cartridge, stow the ribbon as shown in the illustration in step 5. Lamp cartridge 6. Pull up on the handle or ribbon to remove the lamp cartridge.
PAGE 33
User Maintenance 1. 2. 3. 4. Turn on the projector. 5. Press the [ ] key to select “Yes”, and then press the [ENTER] key. 6. Press the [MENU] key to exit the setup menu. Press the [MENU] key to display the setup menu. Press the [ ] key to select “Operational Info”, and then press the [ENTER] key. “Reset Lamp Time” is initially selected, so simply press the [ENTER] key. z This causes the message “Reset Lamp Time?” to appear. z This resets the lamp time to 0 hours.
PAGE 34
Troubleshooting Indicators The status of the indicators lets you know the current operational status of the projector. This section provides details about indicators. z “POWER” in the following table stands for the “POWER/STANDBY” indicator.
PAGE 35
Indicator/Error Message POWER : Amber flashing Amber steady TEMP : Red flashing (1-second interval) Turns off LAMP :– Message : Internal temperature is too high. The projector will turn off. POWER : Amber flashing Red steady TEMP : Red flashing (0.5second interval) :– LAMP Message : – POWER : Green steady :– TEMP :– LAMP Message : The projector has a history of turning off due to high temperature. Check air vents for blockage.
PAGE 36
Troubleshooting Indicator/Error Message POWER : Green steady TEMP :– LAMP :– Message : A system problem has occurred. Some functions may not operate correctly. POWER : Green steady :– TEMP :– LAMP Message : There is some problem with the system. The audio function may not operate correctly. POWER : Green steady :– TEMP :– LAMP Message : There is some problem with the system. Movies may not play back correctly. POWER : Green steady :– TEMP :– LAMP Message : This device is defective.
PAGE 37
Indicator/Error Message POWER : Amber flashing Red steady TEMP : Red steady LAMP :– Message : – POWER : Amber flashing Red steady : Red flashing TEMP (0.5-second interval) : Red flashing LAMP (0.
PAGE 38
Troubleshooting Indicator/Error Message POWER : Amber flashing Red steady TEMP :– LAMP : Red steady Message : The lamp has exceeded its service life! The projector will not turn on until you replace the lamp. Description and Required Action The allowable life for the lamp has been exceeded, and the projector will not turn on. Replace the lamp following the steps under “Replacing the Lamp” (page E-29).
PAGE 39
Troubleshooting Cause and Recommended Action See The “Option Settings 1 Power On Password” setting on the setup menu is turned on, so the projector is password protected. ➔ Input the correct password, and then press the [ENTER] key. User’s Guide (UsersGuide_ English.pdf) The remote controller does not work. The remote controller battery may be dead. ➔ Replace the battery (see “Replacing the Remote Controller Battery”). page E-13 The remote controller may be too far from the projector.
PAGE 40
Specifications Model Name XJ-S31/XJ-S36/XJ-S41/XJ-S46 Projection System DLP DLP chip Size 0.55inch Number of Pixels XGA (1024 × 768) Projection Lens Optical X2 zoom, electric focus Light Source 210W high-pressure mercury lamp Brightness XJ-S31/XJ-S36: 2000 ANSI Lumens XJ-S41/XJ-S46: 2500 ANSI Lumens RGB input terminal RGB mini D-Sub 15-pin × 1 (Also used as component signal input terminal.) AV terminal XJ-S31/XJ-S41: Audio (stereo) 3.5ø mini jack XJ-S36/XJ-S46: Audio (stereo) 3.