Full Product Manual
Table Of Contents
- Contents
- Overview
- Ring Terminals
- Flag Terminals
- Fork Terminals
- Pin Terminals
- Splice Connectors
- Wire Joints
- Heat-Shrinkable Terminals, Splices, Disconnects
- Disconnects and Male Tabs
- Luminaire Disconnects
- Ferrules
- Wire Termination Tools and Installation Kits
- Wire Termination Technical Information
- Shrink-Kon® Heat-Shrinkable Tubing
- Shrink-Kon® Splice Insulatorsand Insulating Covers
- Shrink-Kon® Installation Tools
- Shield-Kon® Shield Termination System
- Dragon-Tooth® Magnet WireTermination System
www.tnb.com
United States
Tel: 901.252.8000
800.816.7809
Fax: 901.252.1354
Technical Services
Tel: 888.862.3289
G-60
Shrink-Kon
®
Heat-Shrinkable Tubing
Wire Termination — Sta-Kon
®
Wire Termination & Insulation
HS Series
............................................................................... HS Series Specifications .................................................................................
• Made of thermally stabilized cross-linked polyolefin,
enabling a recovered wall thickness greater than
the cable jacket replaced
• Withstands severe mechanical requirements of U.R.D.,
submersible, and direct-burial installations
• Tubing, featuring an internally applied sealant, offers
protection against moisture, and may be used over lead,
steel, aluminum, copper, standard plastic and elastomeric
insulating materials
• Shrink temperature of 120° C
• High impact, abrasion, corrosion and chemical resistance
• Rated for 600V, 90° C continuous use. Maximum rating
1kV at 90° C
• Thermoplastic adhesive liner provides complete
environmental protection and insulation
• Meets: UL
®
486D, CSA C22.2 No. 198.2, ANSI C119.1,
Western Underground Guide Numbers 2.4, 2.5, ICEA and
NEMA insulation thickness requirements
• Continuous operating temperature: -55° C to 110° C
PROPERTY TEST METHOD
TYPICAL
PERFORMANCES PROPERTY TEST METHOD
TYPICAL
PERFORMANCES
Physical Chemical
• Tensile Strength ASTM D412, ISO 37 2100 psi (14.5MPa) • Fluid Resistance MIL-DTL-23053 Good to Excellent
• Elongation ASTM D412, ISO 37 600% • Fungus Resistance ASTM G21 No Growth
• Elongation after
Heat Aging
(168 hrs. at 150° C)
ASTM D2671 500% • Copper Corrosion ASTM D2671 No Corrosion
• Heat Shock
(4 hrs. at 225° C)
ASTM D2671 No cracking or flowing • Water Absorption ASTM D570 0.1%
• Longitudinal Change ASTM D2671 +1%, -10% Adhesive
• Low Temperature Flexibility
(4 hrs. at -55° C)
ASTM D2671 No cracking • Adhesive Lap Sheer
(1 in./min. at 23° C)
ASTM D1002 125 psi (.875 MPa)
• Specific Gravity ASTM D792 1.1 • Adhesive Softening Point ASTM E28 92° C ±5° C
• Hardness (Shore D) ASTM D2240 50D • Adhesive Peel Strength
(300mm/min. at 23° C)
ASTM D1000
Electrical — to steel, aluminum, P.E. 35 pli
• Dielectric Strength ASTM D149 500V/Mil (20kV/mm) — PVC 20 pli
• Dielectric Voltage Withstand UL 486D No Breakdown,
(2500V, 60 Hz,
1 Min.)
• Water Penetration STM 706 No penetration after
236 hrs. of continuous
immersion
• Volume Resistivity ASTM D257 1016 ohm-cm
3:1 Shrink Ratio
3:1 Shrink Ratio