Full Product Manual

www.tnb.com
United States
Tel: [phone]
800.816.7809
Fax: [phone]
Technical Services
Tel: [phone]
G-64
Shrink-Kon
®
Heat-Shrinkable Tubing
Wire Termination — Sta-Kon
®
Wire Termination & Insulation
3:1 Shrink Ratio
3:1 Shrink Ratio
HSC Series End Caps
• Provides effective method for sealing cable ends, pipe conduit, etc.
• Extra thickness at the tip of the end cap prevents sharp ends
of the cable from puncturing the seal
• Flame retardant
• Rated from 600/1000V, 90° continuous use
• Shrink temperature of 120° C
• Resistant to common fluids and solvents
• Adhesive liner provides complete environ mental
protection and insulation
• Heat indicating lines. Continuous operating temperature:
-55° C to 110° C
.............................................................................. HSC Series Specifications ................................................................................
PROPERTY
TEST
METHOD
TYPICAL
PERFORMANCE
Physical
• Tensile Strength ASTM D412, ISO 37 2100 psi (14.5MPa)
• Elongation ASTM D412, ISO 37 550%
• Elongation after Heat Aging
(168 hrs. at 150° C)
ASTM D2671 500%
• Heat Shock (4 hrs. at 225° C) ASTM D2671 No cracking
or flowing
• Longitudinal Change on Recovery ASTM D2671 +1%, -10%
on Recovery
• Low-Temperature Flexibility
(4 hrs. at -55° C)
ASTM D2671 No cracking
• Specific Gravity ASTM D792 1.10
• Hardness (Shore D) ASTM D2240 50D
Electrical
• Dielectric Strength ASTM D149 500V/Mil (20kV/mm)
• Dielectric Voltage Withstand UL 486D No Breakdown
(2500V, 60 Hz, 1 Min.)
• Volume Resistivity ASTM D257 1016 ohm-cm
HSC Series Heat-Shrinkable End Caps
CAT. NO.
MIN.
EXPANDED
I.D. (IN.)
MAX
RECOVERED
I.D. (IN.)
RECOVERED
WALLED (IN.)
CODE CABLE
SIZE
STANDARD
LENGTH (IN.)
STD.
PKG. QTY.
HSC8-4 .51 .16 .09 #8–#6 AWG 2.50 10
HSC2-20 .75 .24 .09 #6–#2 AWG 2.50 10
HSC30-250 1.10 .35 .12 #1–3/0 AWG 3.00 5
HSC300-600 1.50 .47 .16 2/0 AWG–350 kcmil 3.50 5
HSC700-1000 2.00 .63 .16 250–500 kcmil 3.50 5
HSC750 2.70 .87 .16 600–1000 kcmil 4.00 10
HSC300* 3.50 1.18 .16 800–1250 kcmil 4.50 5
HSC500* 4.70 1.57 .17 1500–2500 kcmil 5.50 5
Order multiple is std. pkg.
*Not UL Listed or CSA Certified.
PROPERTY
TEST
METHOD
TYPICAL
PERFORMANCE
Chemical
• Fluid Resistance MIL-DTL-23053 Good to Excellent
• Fungus Resistance ASTM G21 No Growth
• Copper Corrosion ASTM D2671 No Corrosion
• Water Absorption ASTM D570 .1%
Seal Integrity
• Adhesive Lap Shear
(1 in./min. at 23° C)
ASTM D1002 130 psi (.91 MPa)
• Adhesive Softening Point ASTM E28 92° C ±-5° C
• Adhesive Peel Strength
(300mm/min. at 23° C)
— to steel, aluminum, P.E.
— PVC
ASTM D1000 (mod.)
35 pli
20 pli
• Adhesive Blocking (30° C) ASTM D1146 No Blocking
• Water Penetration STM 706
No penetration after 236 hrs.
of continuous immersion
• Room Temperature 168 hrs./40 psi No leaks
• Temp. Cycling (-40° C to 60° C) 50 cycles/15 psi No leaks
• Burst Pressure 100 psi (0.70 MPa)