Full Product Manual

www.tnb.com
United States
Tel: [phone]
800.816.7809
Fax: [phone]
Technical Services
Tel: [phone]
G-72
Shrink-Kon
®
Splice Insulators and Insulating Covers
Wire Termination — Sta-Kon
®
Wire Termination & Insulation
• Available in a 25-ft. roll
• Used in conjunction with T&B
Heat-Shrinkable Insulators for
better moisture sealing
CAT. NO. DESCRIPTION
WIDTH
(IN.)
THICKNESS
(IN.)
LENGTH
(FT.)
STD.
PKG. QTY.
HSTS25 Tape Sealant 1 .06 25 1
Standard package is reels. Order by reel; not by feet.
1. The cable jacket and conductors should be relatively clean
and free of greases, oils and other foreign substances.
2. It is best to overlap each wrap of tape by
1
⁄4 to
1
⁄2 of the width
for the best seal.
3. When using heat-shrinkable products, most applications require
only one or two layers of tape prior to sliding tubing in place.
4. Shrink the tubing, cap, boot, etc., following the installation
procedure for the applicable heat-shrinkable part.
To seal the junction or crotch of an application requiring two
or more cables, conductors, etc. without a common jacket.
1. Apply the overlapped one or two layers around each cable, conductor,
etc., at the same distance from the connector, or ball up the sealant
and press into crotch or junction of the joint.
2. Apply two overlapping wraps over the bundle.
3. Slide the expanded heat-shrinkable part over the joint and shrink.
Installation Guidelines
HSTS25 — Tape Sealant
CAT. NO.
WIDTH
(IN.)
LENGTH
(FT.)
THICKNESS
(MILS) COLOR
STD.
PKG. QTY.
Self-Fusing Insulation Tape
TBFT421-36 1 36 40 Red 10
TBFT201-36 1 36 20 Black 10
Smooth Filler Putty Compound
TBFP9-2 1 2.08 — White 1
Standard package is rolls. Order by rolls; not by feet.
Typical Applications
• Repair deteriorated insulation on cables and conductors
• Insulate and seal underwater, underground and above-ground
bonding installations
• Insulate harnessing, bundling, cabling and wiring in aircraft,
automotive, marine and other industrial machinery/equipment
• Material: Modified silicone rubber compound
• Tensile Strength: 1200 psi
• Dielectric Strength: 20 mil: 600 vpm;
40 mil: 400 vpm
• Abrasion Resistance: 110 lbs./in.
• Water Absorption: < .5%
• Temperature Rating: 80° C max.
• Voltage Rating: 600V max.
Quick and easy insulation — no heat or adhesive required!
Self-Fusing Insulation Tape
• Just two layers form a moisture-proof,
abrasion-resistant, dielectric seal
• Easy-release, non-static-sensitive
liner peels right off
• Creates an immediate, permanent
bond even when wet
• Suitable for high- and low-voltage
applications
• Resistant to UV, moisture
and saltwater
• Easily removable — just slice with
a knife and pull off — leaves no residue
• Smooth filler putty compound available for use under tape
when insulating bolted or dimensionally inconsistent splices
and terminations
TBFP9-2
TBFT421-36
....................... Specifications ....................
.....................................Specifications .................................
Physical
• Description: Butyl Rubber Polymer
• Application Temperature: 40° F to 100° F
• Service Temperature: -40° F to 180° F
• Environmental Resistance: Resists ozone and all normal aging processes
Electric
• Dielectric Strength: 250V/mil minimum
• Volume Resistivity: 1014 ohms/cm
Chemical
• Chemical Resistance: Resists acids, bases and alcohols;
Passes Fed. Spec. SS-S-00210, section 3.6