Installation Guide

102006 - AUTOMATIC TRANSFER SWITCH WITH aXis CONTROLLER™ MODULE
SPECIFICATIONS
13
6. Return UTILITY circuit breaker to the ON position. ATS will
transfer load back to utility and generator will cool down and
shut off.
7. Repeat this process if LMM units are added or removed from
the system.
11 12
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
Full System Check
1. Open Utility breaker for full system test, close breaker after
confirming all systems working.
2. After Utility breaker opens engine will start automatically.
3. aXis ATS control panel will reboot on Generator power and
control switching of latching relays.
4. Home is now powered by Generator. If Load Management
modules (LMM) have been installed, they will become active
after 5 minutes.
5. Close Utility breaker
6. System is now fully functional.
7. Replace the deadfront by sliding it from the bottom up
into the cabinet; panel should index into the door latch
protrusions. Secure it to the deadfront bracket with included
nut and stud.
8. Replace the door and secure with included hardware. It is
recommended to secure the door with a lock.
9. Return to HSB and verify the controller is in “AUTO” mode.
Confirm icons indicate Utility power is active, Utility side relay
is closed, and home is receiving power.
10. Close and lock HSB hoods return keys to customer.
NEMA 1 – This type of enclosed ATS is for indoor installations
only.
NEMA 3R – This type of enclosed ATS is similar to the indoor box,
except that it is a weatherproof enclosure and required for exterior
installations by code. The enclosure only has knockouts on the
bottom side for the enclosure, requires water tight fasteners/
grommets when installed outside per code. This enclosure can
also be used inside.
SPECIFICATIONS
aXis Controller
TM
Module Automatic
Transfer Switch
Model Number ................................................................ 102006
Enclosure Style ...............................................NEMA 3R outdoor
Maximum Amps ................................................................... 200
Nominal Volts ................................................................ 120/240
Load Management Circuits ....................................................... 4
Weight ................................................................ 43 lbs (19.6 kg)
Height .................................................................28 in. (710mm)
Width ..................................................................20 in. (507mm)
Depth ................................................................. 8.3 in. (210mm)
Technical Specifications
– 22kAIC, no short-time current rating.
– Suitable for use in accordance with the National Electrical
Code, NFPA 70.
– Suitable for control of motors, electrical discharge lamps,
tungsten filament lamps, and electrical heating equipment,
where the sum of the motor full load ampere ratings and the
ampere ratings of the other loads does not exceed the ampere
rating of the switch, and the tungsten load does not exceed
30% of the switch rating.
– Continuous load not to exceed 80% of switch rating.
– Line voltage wiring: Cu or AL, min 60°C, min AWG 1 – max
AWG 000, torque to 250 in-lb.
– Signal or Com Wiring: Cu only, min AWG 22 – max AWG 12,
torque to 28-32 in-oz.
WARRANTY
Each Champion transfer switch or accessory is guaranteed against
mechanical or electrical failure due to manufacturing defects
for a period of 24 months following shipment from the factory.
The manufacturer’s responsibility during this warranty period
is limited to repair or replacement, free of charge, of products
proving defective under normal use or service when returned to
the factory, transportation charges prepaid. Guarantee is void
on products that have been subjected to improper installation,
misuse, alteration, abuse or unauthorized repair. The manufacturer
makes no warranty with respect to the fitness of any goods for
a user’s particular application and assumes no responsibility for
proper selection and installation of its products. This warranty is
in lieu of all other warranties, expressed or implied, and limits the
manufacturer’s liability for damages to the cost of the product.
This warranty gives you specific legal rights, and you may have
other rights, which vary from state to state.