AUX UNLOCK DOOR 1 CHIME 1 DOOR 1 TELCO INPUT CHIME 2 DOOR 2 TELCO OUTPUT UNLOCK DOOR 2 CO / No CO #/* Model P-0921 PRO CHANNEL V ISION TM TELCO 2-DOOR TELEPHONE ENTRY CONTROLLER INPUT OUTPUT DOOR 1 PAGE DOOR 2 POWER P-0921 2-DOOR TELEPHONE ENTRY CONTROLLER PRO 6
The P-0921 provides communication between two different Channel Vision door intercoms and any phone in the house. When a visitor presses the doorbell button the phones in the house will respond with a distinctive ring. The home owner can then speak to the visitor by answering any of the ringing phones in the house.
Other Telephone Entry Components Door-Intercom Units: Your telephone entry system will require at least one of the following compatible door-intercom stations. These door intercoms are constructed of 1/4” solid brass and are offered in 9 different finishes to match the most popular door hardware. They can be ordered with or without a hidden camera for covert surveillance. Both color and black & white camera options are available. DP Intercom...
Basic Setup & Operation When the button is pressed on the door-intercom, the phones in the house will ring. If a doorbell chime and transformer are connected to the CHIME contact, the doorbell chime will also be heard. If the phone is answered within 20 seconds, it will be automatically connected to the door-intercom. If the phone is answered after 20 seconds simply press ## (or **) to be connected.
User Codes User codes for P-0921 Replace x with # or * depending on the position of the #/* switch.
Programming Codes To program the advanced options of the P-0921 pick up any telephone in the system and enter the touch-tone codes listed in the chart below. Default Settings: CHIME 1 and 2 are momentary closure.
Four Door Application AUX CHIME 1 DOOR 1 TELCO INPUT Set this switch for # operation DOOR 2 CHIME 2 UNLOCK DOOR 2 CO / No CO TELCO OUTPUT Telephone Service UNLOCK DOOR 1 Two of the P-0921 can be used to serve up to 4 different door-intercoms. Simply connect and configure the units as shown below. Note: be sure to set one unit for # operation and the other unit for *.
Using the TE110DS The TE110DS is not always required when using the P-0921, because the P-0921 has a built in AUX relay that can be programmed to control one electronic door strike. However, it may still be used for applications that require a remote contact closure that is located near the door intercom station. If using the RJ-45 connection on the P-0921, simply connect the green and green-white wires from the CAT5 to the terminal inputs and outputs of the TE110DS as shown below.
Using the Page Out Function One major benefit of the 2-Door Telephone Entry System is that many different components can be integrated with it. The system below integrates the Page Out feature of the P-0921 with the local audio input on the P-1014 1x4 CAT5 Audio Distribution Module. When a page is sent from the P-0921 it will interrupt the main audio source feeding the P-1014 so the page will be heard through the audio system’s speakers.
Stripping and Connecting CAT5 Wire CAT5 cable should be stripped with a proper stripping tool, such as Channel Vision’s J-110 tool. 1. Place the CAT5 between the blade and the first notch of the J-110 tool. Blade Cat5 2. Rotate the tool only once. Multiple turns will cause you to cut into the inner wires. Rotate 1 turn only 3. Inspect the inner wires for damage. If any wires are cut start over at step 1.
Troubleshooting 1) When the doorbell is pressed the phones do not ring, but you can activate and speak to the door station by pressing *1 (or #1 depending on setup). a. Make sure that you have the correct power supply and that it is supplying 12 VAC. b. Measure the AC voltage on the “TELCO Output” terminals at the time when the unit should be ringing (just after the doorbell button is pressed). There should be between 70 - 90 VAC across the terminals during a ring cycle.
Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abuse, or alteration of the equipment.