Dimensions Guide

18
Charlotte, Charlotte Pipe and “You can’t beat the system” are registered
trademarks of Charlotte Pipe and Foundry Company.
All products manufactured by Charlotte
Pipe and Foundry Company are proudly
made in the U.S.A.
Limited Warranty
Charlotte Pipe and Foundry Company
®
(Charlotte Pipe
®
)
Products are warranted to be free from manufacturing
defects and to conform to currently applicable ASTM
standards for a period of five (5) years from date of
delivery. Buyer’s remedy for breach of this warranty is
limited to replacement of, or credit for, the defective
product. This warranty excludes any expense for removal
or reinstallation of any defective product and any other
incidental, consequential, or punitive damages. This limited
warranty is the only warranty made by seller and is
expressly in lieu of all other warranties, express and
implied, including any warranties of merchantability and
fitness for a particular purpose. No statement, conduct
or description by Charlotte Pipe or its representative, in
addition to or beyond this Limited Warranty, shall constitute
a warranty. This Limited Warranty may only be modified in
writing signed by an officer of Charlotte Pipe.
This Limited Warranty will not apply if:
1) The Products are used for purposes other than their
intended purpose as defined by local plumbing and
building codes, and the applicable ASTM standard.
2) The Products are not installed in good and workmanlike
manner consistent with normal industry standards;
installed in compliance with the latest instructions
published by Charlotte Pipe and good plumbing practices;
and installed in conformance with all applicable
plumbing, fire and building code requirements.
3) This limited warranty does not apply when the products
of Charlotte Pipe are used with the products of other
manufacturers that do not meet the applicable ASTM
or CISPI standards or that are not marked in a manner
to indicate the entity that manufactured them.
4) In hubless cast iron installations, this warranty will not
apply if products are joined with unshielded hubless
couplings. Charlotte Pipe requires that its hubless cast
iron pipe and fittings be joined only with shielded hubless
couplings manufactured in accordance with CISPI 310,
ASTM C 1277 and certified by NSF
®
International or
with Heavy Duty Couplings meeting ASTM C 1540.
5) The Products fail due to defects or deficiencies in design,
engineering, or installation of the piping system of which
they are a part.
6) The Products have been the subject of modification;
misuse; misapplication; improper maintenance or
repair; damage caused by the fault or negligence of
anyone other than Charlotte Pipe; or any other act or
event beyond the control of Charlotte Pipe.
7) The Products fail due to the freezing of water in the
Products.
8) The Products fail due to contact with chemical agents,
fire stopping materials, thread sealant, plasticized vinyl
products, or other aggressive chemical agents that are
not compatible.
9) Pipe outlets, sound attenuation systems or other devices
are permanently attached to the surface of Charlotte
®
PVC, ABS or CPVC products with solvent cement or
adhesive glue.
Charlotte Pipe products are manufactured to the applicable
ASTM or CISPI standard. Charlotte Pipe and Foundry
cannot accept responsibility for the performance,
dimensional accuracy, or compatibility of pipe, fittings,
gaskets, or couplings not manufactured or sold by Charlotte
Pipe and Foundry.
Any Charlotte Pipe products alleged to be defective must be
made available to Charlotte Pipe at the following address
for verification, inspection and determination of cause:
Charlotte Pipe and Foundry Company
Attention: Technical Services
2109 Randolph Road
Charlotte, North Carolina 28207
Purchaser must obtain a return materials authorization
and instructions for return shipment to Charlotte Pipe of
any product claimed defective or shipped in error.
Any Charlotte Pipe product proved to be defective in
manufacture will be replaced F.O.B. point of original
delivery, or credit will be issued, at the discretion of
Charlotte Pipe.
4/24/15
Testing with or use of compressed air or gas in PVC / ABS
/ CPVC pipe or fittings can result in explosive failures and
cause severe injury or death.
• NEVER test with or transport/store
compressed air or gas in PVC / ABS / CPVC
pipe or fittings.
• NEVER test PVC / ABS / CPVC pipe or
fittings with compressed air or gas, or air
over water boosters.
• ONLY use PVC / ABS / CPVC pipe or
fittings for water or approved chemicals.
• Refer to warnings on PPFA’s website and
ASTM D 1785.