READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Installation Guide Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly. pgs. 4 - 5 Wiring. pg. 6 Canopy Assembly. pg. 6 Blade Assembly. pg. 7 Light Kit Assembly. pgs. 7- 8 Testing Your Fan. pg. 8 Troubleshooting. pg. 9 Parts Replacement. pg. 9 Warranty. pg. 9 4007498 net weight of fan: 16.95 lb (7.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a. canopy. 1 piece a b d e c b. hanging bracket. 1 piece c. downrod and hanging ball (with pin and clip). 1 piece d. canopy ring. 1 piece f e.
12 ft. - 20 ft. (3.66 m - 6.1 m) 3. Installation Preparation. blade edge To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7ft. (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square feet (37.2 square meters). This fan can be mounted with a downrod on a regular (no-slope) or vaulted ceiling. The hanging length can be extended by purchasing a longer downrod (0.5in./1.27cm diameter).
. Fan Assembly (with downrod). stop pin Remove hanging ball from downrod provided by loosening set screw on hanging ball. Remove pin and clip. Lower hanging ball and remove stop pin and then slide hanging ball off of the downrod. [Refer to diagram 1.] Loosen yoke set screws and nuts at top of motor housing. [Refer to diagram 2.
5. Fan Assembly (with downrod). (cont.) wood ceiling joist With the hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket and let hanging ball rest on the hanging bracket. Turn the hanging ball slot until it lines up with the hanging bracket tab.
. Wiring. WARNING: Turn off circuit breakers to current fixture from breaker panel and be sure switch is turned to the OFF position. white supply wire ground (green or bare) black supply wire CAUTION: Be sure outlet box is properly grounded and that a ground wire (GREEN or Bare) is present. Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code.
9. Blade Assembly. WARNING: To reduce the risk of serious bodily injury, DO NOT use power tools to assemble the blades. If overtightened, blades may crack and break. Time Saver: Washers for blade screws can be set on each blade screw prior to installing blades. motor housing blade attachment screws/lock washers Locate 15 blade attachment screws and washers in hardware packs. Hold blade arm up to blade and align holes.
10. Light Kit Assembly. (cont.) Remove finial, finial plate, hex nut, flat washer and rubber washer from threaded rod on light kit fitter. Raise glass shade in order to guide pull chains through corresponding holes in glass shade. Align threaded rod on light kit fitter with hole in middle of glass shade and push up gently, allowing threaded rod to come through hole. Replace rubber washer and flat washer on threaded rod and secure glass shade with hex nut that was previously removed.
Troubleshooting. WARNING: Failure to disconnect power supply prior to troubleshooting any wiring issues may result in serious injury. Warranty. LIFETIME LIMITED WARRANTY: We warrant this fan to the original household purchaser for indoor use under the following provisions: 1-YEAR WARRANTY: We will replace or repair any fan which has Problem: Fan fails to operate. Solutions: 1. Check wall switch to fan. 2. Verify that reverse switch is set completely in either direction. 3.