Snapshot Use on Dimmer Outdoor Use Sound Activated DMX Master/Slave Auto-ranging Power Supply Replaceable Fuse User Serviceable Duty Cycle User Manual 3000 N 29th Ct, Hollywood, FL 33020 U.S.A. (800) 762-1084 – (954) 929-1115 FAX (954) 929-5560 www.chauvetlighting.
TABLE OF CONTENTS 1. BEFORE YOU BEGIN ................................................................................................................................................... 3 WHAT IS INCLUDED ................................................................................................................................................................................ 3 UNPACKING INSTRUCTIONS ........................................................................................................
1. BEFORE YOU BEGIN What is included 1 x Mini 4BAR™ 1 x Mini 4BAR™ Carrying case 1 x Tripod Stand 1 x Tripod Stand Carrying Case 1 x Wired Footswitch (with 16ft cable) 1 x Warranty Card 1 x User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition.
Safety Instructions Please read these instructions carefully. It includes important information about the installation, usage and maintenance of this product. Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture.
2. INTRODUCTION Features Complete LED wash system Includes footswitch with 16 ft cable, tripod with bag and transport case for lights Safely mounts to truss with clamps Independent positioning of each light Low-profile lights are 1.2 in deep Adjustable stand from 54 in to 85 in Built-in automated programs Built-in sound activated programs Features (footswitch) Trigger built-in static or automated programs (includes RGB fades) Instantly triggers sound active mode Instantly blackout any program 2.
Product Overview Microphone Sensitivity Adjustment Knob Tripod Stand Securing Knob Back Panel Microphone Fuseholder Lights (4) Tripod Stand Mini 4BAR™ Carrying Case Foot Switch 2.
3. SETUP AC Power This fixture runs on 100~240 VAC, 50/60 Hz. Before powering on the unit, make sure the line voltage to which you are connecting it is within the range of accepted voltages. Always connect the fixture to a switched circuit. Never connect the fixture to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only as a 0 to 100% switch.
Orientation This fixture may be mounted on the included tripod stand, in any location, provided there is adequate room for ventilation. Rigging There are two methods of mounting this fixture. Using the included tripod stand Using a clamp on the two clamp hanging bolts Adjust the angle of the each of the four lights on the fixture by loosening both knobs and tilting the fixture. After finding the desired position, retighten both knobs.
Tripod Stand This fixture may be mounted on the included tripod stand. 1. 2. 3. 4. 5. 6. 7. 8. 9. Setup the Tripod stand on a sturdy platform that is capable of holding at least 10 times the weight of the stand with Mini 4BAR™. Use the Tripod Legs Adjustment Knob to slide open the legs and set the tripod to a safe operating level. Adjust the stand height to the minimum operating height level using the Height Adjustment Knob and the safety pin. The Safety Pin must be used.
4. OPERATING INSTRUCTIONS Pedal #1 (Auto Program Selection) Pedal #2 (Blackout) Footswitch operation The included footswitch provides quick access to preset colors, color change programs, and sound triggering via the onboard microphone on the Mini 4BAR™. Please see the chart, along with the set of instructions, below for further explanation. 1. 2. Power on the fixture. Connect the footswitch to the Mini 4BAR™ via the 3-pin connection cable with plug.
5. APPENDIX General Maintenance To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month. Dust build up reduces light output performance and can cause overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off fixture before conducting maintenance. Unplug fixture from power.
General Troubleshooting SYMPTOM Blown Fuse/ Tripped Breaker Device does not power up Fixture is not responding to DMX Loss of signal POSSIBLE CAUSE(S) POSSIBLE ACTION(S) Short circuit along the power wires Replace Fuse Excessive circuit load Reset Breaker No power Check for power on power outlet Loose power cord Check power cord Blown Fuse Replace Fuse Reset Breaker Reset Breaker Wrong DMX addressing Check Control Panel and unit addressing Damaged DMX cables Check DMX cables Wrong pola
Returns Procedure Returned merchandise must be sent prepaid and in the original packing; call tags will not be issued. Package must be clearly labeled with a Return Merchandize Authorization Number (RMA #). Products returned without the RMA # will be refused. Call CHAUVET® and request an RMA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return.
Technical Specifications WEIGHT & DIMENSIONS Length ............................................................................................................................... 3 in (76 mm) Width............................................................................................................................. 38 in (965 mm) Height (light fixture only, NOT mounted on the included stand) ....................................... 9 in (229 mm) Height (using the stand) ...............................