Operation Manual
9
8
O, located on the same side where you are tting
the Child Car Seat.
Diag. 10 – Check that the Child Car Seat is tightly
and correctly tted into the car seat, and that the
safety belt is well tensioned. If the Child Car Seat is
not tightly and safely tted into the car seat, repeat
the installation.
WARNING! Always check that all parts of the safety
belt are well tensioned and that it is not twisted.
WARNING! NEVER use the safety belt in positions
other than those indicated in these instructions.
HOW TO FIT THE CHILD CAR SEAT INTO THE
CAR FOR GROUP 1 (From 9 up to 18 kg)
WARNING! When it is used for Group 1 (from 9 up
to 18 kg), always t the Child Car Seat in a forward-
facing direction.
If the Child Car Seat is tted in the front seat of the
car, it is recommended to push the seat back as
much as possible, bearing in mind the comfort of the
passenger sitting in the seat directly behind it, and to
adjust the backrest in the most vertical position.
If the car is equipped with a safety belt height adju-
ster, x it in the lowest position. Then check that the
car seat safety belt adjuster is either in a backward
position with respect to the backrest of the car seat
(or at least aligned to it).
WARNING! The points through which the safety belt
must pass for tting for Group 1 (from 9 up to 18 kg)
are highlighted in RED.
Adjust the Child Car Seat to the most reclined posi-
tion (Diag. 6), with the handle K.
Diag. 11 – Position the Child Car Seat on the selected
car seat in the forward-facing position.
Diag. 12 – Hold the 3-point safety belt of the car and
insert it between the base and seat; then fasten it to
the opposite side.
Diag. 13 – Pass the horizontal section of the safety
belt (lap section) under the two red belt guides M.
Diag. 14 – Tension the safety belt as much as pos-
sible, holding it from the diagonal section (thoracic
section).
Diag. 15 – Press the button located on the locking
clamp N, located on the side where you are tting
the child car seat; then insert the diagonal section
of the belt into the clamp. Release the button, which
will automatically return to the lock position. Ten-
sion the safety belt as much as possible.
Diag. 16 – Insert the upper part of the diagonal belt
inside the guide O.
Diag. 17 – Tension the belt as much as possible, ensu-
ring that the Child Car Seat adheres correctly to the car
seat. If necessary, carry out this operation exercising
some pressure on the Child Car Seat with your knee.
Diag. 18 – Check that the Child Car Seat is tightly
and correctly tted into the car seat, and that the
safety belt is well tensioned. If the Child Car Seat is
not tightly and safely tted into the car seat, repeat
the installation.
WARNING! Always check that all parts of the safety
belt are well tensioned and that it is not twisted.
WARNING! NEVER use the safety belt in positions
other than those indicated in these instructions.
HOW TO ADJUST THE SAFETY HARNESS
WARNING! The safety harness must always be adju-
sted to suit the child’s growth.
Diag. 19 – To adjust the safety harness correctly,
the straps must come out from the backrest, at the
height of the child’s shoulders.
Adjust the safety harness as illustrated below:
Adjust the Child Car Seat to the most reclined posi-
tion with the handle K (Diag. 6).
Diag. 20 – Press the harness adjustment button
found inside its compartment F and, at the same
time, take hold of the two child car seat harness
straps D, below the shoulder straps, and pull them
towards you to slacken them.
Diag. 21 – Unfasten the safety harness, pressing the
red button on the buckle.
Diag. 22 - Remove the two harness straps from the
locking plate P, located on the rear of the backrest.
Diag. 23 – Pull the harness straps from the front
to remove them from the backrest and shoulder
straps.
Diag. 24 – Remove the shoulder straps, turning and
removing the locking plates from the respective ho-
les on the backrest.
Diag. 25 – Reinsert the plates of the shoulder straps
at the desired height, inside the respective holes on
the backrest.
Diag. 26 – Lock the two tabs into the buckle. This will
help you to check that the harness strap is inserted
in the correct position.
Diag. 27 – First insert the two harness straps through
the shoulder straps; then insert them into the holes
located on the backrest and into the locking plates
of the shoulder straps.
Diag. 28 – Reinsert the two harness straps into the
plate.
Diag. 29 - Check that both the plate and harness
straps are positioned as shown in the diagram.
WARNING! Check that the harness is not twisted.
SEATING THE CHILD IN THE CHILD CAR SEAT
Loosen and unfasten the harness of the Child Car
Seat, as illustrated in the “HOW TO ADJUST THE
HEIGHT OF THE SAFETY HARNESS” paragraph,
Diag. 20 and 21.
Diag. 30 – Sit the child in the Child Car Seat.
WARNING! Always check that the child is sitting
with its back correctly placed against the backrest
of the Child Car Seat, and that the crotch strap is in
the correct position.
Diag. 31 – Take the harness and join the two buckle
tabs.
Diag. 32 – Firmly push the two joined buckle tabs
inside the buckle, until a “click” is heard. To ensure
maximum safety, the two buckle tabs have been de-
signed so as to prevent the locking of a single tab, or
one tab at a time.