User's Manual

ManualsBrandsCHIEF ManualsTV MountCHIEF TV Mount PAC-500

INSTALLATION INSTRUCTIONS

CHIEF MANUFACTURING INC.

1-800-582-6480 952-894-6280 FAX 952-894-6918

8401 EAGLE CREEK PARKWAY, STE 700

SAVAGE, MINNESOTA 55378 USA

8800-000058 Rev E

2007 Chief Manufacturing

www.chiefmfg.com

06/07

BEFORE YOU BEGIN

LARGE FLAT PANEL IN WALL ENCLOSURE

Model: PAC-500

Specifications:

• Designed for in-wall installation spanning a

minimum of 3 wood studs, 16" on center.

• Accomodates MWR, PWR and PNR swing arm

mounts.

• Cutouts provided for single gang electrical box

and grommet hole for audio/video cables.

• Weight capacity of 200 lbs (90 kg).

NOTE: Shown with PNR mount installed; MWR/PWR

mount similar (mount not included).

WARNING: It is the installer’s responsibility to make sure all components are properly assembled and installed

using the instructions provided. Failure to read, thoroughly understand, and follow all instructions can result in

serious personal injury, damage to equipment, or voiding of factory warranty.

• If you have any questions about this these instructions or your specific installation, contact Chief Manufacturing

at 1-800-582-6480 or 952-894-6280.

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS LARGE FLAT PANEL IN WALL ENCLOSURE Model: PAC-500 Specifications: • • • • Designed for in-wall installation spanning a minimum of 3 wood studs, 16" on center. Accomodates MWR, PWR and PNR swing arm mounts. Cutouts provided for single gang electrical box and grommet hole for audio/video cables. Weight capacity of 200 lbs (90 kg). NOTE: Shown with PNR mount installed; MWR/PWR mount similar (mount not included).
PAGE 2
Model: PAC-500 Installation Instructions IMPORTANT WARNINGS AND CAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. WARNING: It is the installer’s responsibility to make sure the structure to which this unit is attached can support five times the combined weight of all equipment.
PAGE 3
Installation Instructions Model: PAC-500 TOOLS REQUIRED FOR INSTALLATION • • • • • • • • • Stud Sensor Level Saw Tape Measure Screwdriver (for wood screws) 9/16" Wrench 3/16" Hex Key (provided) 4mm Hex Key (provided) 4mm Hex Bit (provided) 10 NOTE: Other tools may be required depending on your method of installation. 60 PARTS After unpacking carton, inspect and verify contents (See Figure 1). If any listed parts are missing or damaged, contact Chief Customer Service at 1-800-582-6480.
PAGE 4
Model: PAC-500 Installation Instructions INSTALLATION AND ASSEMBLY The following instructions are applicable to: • • Three 2x4 studs, 16" on center; other installations are possible with increased framing complexity. MWR/PWR (single swing arm) and PNR (double swing arm) mounts. OPEN WALL 1. Determine approximate mounting location, keeping in mind the display size. ! IMPORTANT: Installation of housing (10) in 2x4 wall results in nearly direct contact with vertical studs and opposite (back) wall.
PAGE 5
Installation Instructions Model: PAC-500 5. Attach horizontal framing to each support block with two #10 x 2-1/2" countersunk wood screws (See Figure 3). INSTALL HOUSING NOTE: See instructions that came with MWR/PWR/PNR mount for specific display removal procedures. 1. Disconnect all cables from display. WARNING: ELECTRICAL SHOCK AND FIRE HAZARD! Consult a qualified electrical contractor and applicable electrical codes. Failure to take adequate precautions can cause DEATH or SERIOUS PERSONAL INJURY! 1.
PAGE 6
Model: PAC-500 Installation Instructions 70 (2 places) 120 (2 places) 110 (2 places) 20 PNR PNR Mount 40 (2 places) MWR/PWR Mount 90 (2 places) 140 (2 places) Figure 8: Attach Lower Bracket (PNR Mount) Figure 6: Attach Upper Bracket 6. Attach lower bracket (30): • • MWR/PWR mount: Using key (170), attach lower bracket (30) to mount assembly with screws (80) and washers (130) (See Figure 7). Tighten securely.
PAGE 7
Installation Instructions Model: PAC-500 • 80 (2 places) 130 (2 places) Housing edge gaps may be filled with (optional) drywall compound or other filler material. 50 Edge of drywall 20 110 (2 places) 30 120 (2 places) 70 (2 places) NOTE: Faceplace removed for clarity. Figure 10: Install MWR/PWR Mount 80 (2 places) 130 (2 places) 150 (18 places) 60 Figure 12: Install Moulding INSTALL DISPLAY NOTE: See instructions that came with MWR/PWR/PNR mount for specific display installation procedures.
PAGE 8
Model: PAC-500 8 Installation Instructions