Owners manual

ManualsBrandsChild Craft ManualsBabyCamden Dressing Table, Matte White

Foundations

Worldwide, Inc.

• 5216 Portside Dr., Medina, OH 44256 USA • PH: 1 877.716.2757 (U.S. Only) or +1 330.722.5033 • FAX: +1 330.722.5037

• www.childcraft-furniture.com / www.foundations.com

Assembly Directions AnD PArts list

Directions for maintenance, cleaning, storage and use of your Changing Table are also included.

BEFORE STARTING THE ASSEMBLY PROCEDURE, READ ALL DIRECTIONS WITH CARE.

YOU WILL NEED THE FOLLOWING FOR THE ASSEMBLY OF YOUR CHANGING TABLE:

#2 PHILLIPS SCREWDRIVER - FLAT TIPPED SCREWDRIVER

Dressing tAble

1216

PArts PAckeD in cArton AnD HArDwAre bAg

SI644B

(1) Allen Wrench

PArts encloseD in cArton

(16) Allenhead Bolts

(2) Allenhead Bolts

(2) Hex Nut

(2) Nylon Washer

(1) Dressing Pad

(1) Belt

(1) End Assembly-Right

(1) End Assembly-Left

(1) Top Back Assembly

(1) Top Front Rail

(1) Top Shelf Front Rail

(4) Lower Front Back Rail

No groove in face

Note wide groove

Note narrow groove

(1) Top Shelf

Holes

in face

(2) Lower Shelf

Warning

Label

SI644B (EN) 051513.indd 1 5/15/13 10:48 AM

Summary of content (5 pages)

PAGE 1
Dressing Table 1216 Foundations® Worldwide, Inc. • 5216 Portside Dr., Medina, OH 44256 USA • PH: 1 877.716.2757 (U.S. Only) or +1 330.722.5033 • • www.childcraft-furniture.com / www.foundations.com 1 FAX: +1 330.722.5037 Assembly Directions and Parts List Directions for maintenance, cleaning, storage and use of your Changing Table are also included. BEFORE STARTING THE ASSEMBLY PROCEDURE, READ ALL DIRECTIONS WITH CARE.
PAGE 2
Preparation Carefully remove and lay out all hardware and parts. Check quantities and match the Hardware List and the Parts List. NOTE: During the assembly process, when using screws or bolts, check each with the Parts Enclosed in Hardware Bag list by letter and size identification. Place each screw or bolt on the diagram of the item which is sketched actual size. Be sure to use the proper size specified in the assembly directions.
PAGE 3
Step 2 - Diagram 2: Shelf Assembly Slide Shelves O and N into receiving grooves as shown. N Warning Label Note holes through face in this part. O O Slide shelf into groove in End Assembly - Right Slide into grooves. Step 3 - Diagram 3: Attaching End Assembly-Left To Assembled End Assembly-Right Attach End Assembly - Left I following the same process as complete during Step 1. Also guide shelves O and N into the receiving grooves in End Assembly - Left I.
PAGE 4
Step 4 - Diagram 4: Attaching And Using Restraint Belt Align the holes in each end of Restraint Belt G with the holes in the Top Shelf N. Attach by inserting Washer E on Bolt C then through the hole in the Top Shelf N. Secure using a Hex Nut D threaded onto Allenhead Bolt C from the underside as shown. Tighten securley. NOTE: Style of Dressing Table may vary. C G E C G D Place the Foam Dressing Pad F on Top Shelf as shown before using. Read all WARNINGS before use.
PAGE 5
warning label ! WARNING  FALL HAZARD - To prevent death or serious injury, always keep child within arm’s reach. ! WARNING  •READ ALL INSTRUCTIONS BEFORE USING THIS CHANGING TABLE. •FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. •FALL HAZARD - TO PREVENT DEATH OR SERIOUS INJURY, ALWAYS KEEP CHILD WITHIN ARMS REACH. •DO NOT USE THIS CHANGING TABLE AS A CHANGING AREA IF THE RAILS ARE LOOSE, BROKEN OR MISSING.