UPRIGHT FREEZER USER MANUAL MODEL CSF166NW CSF165NSS Customer Service 1300 796 688 www.chiq.com.
PART NAMES AND LOCATIONS No 1 2 3 4 Description Control panel Flip cover Freezer drawers Adjustable Feet IN ACCESSORY BAG: USER MANUAL, WARRANTY CARD As the manufacturer holds the authority to redesign or modify its products without notice: Any modifications or upgrades of our products will result in this Freezer varying slightly from this manual but the functionality will remain the same to that as set out within this manual.
IMPORTANT SAFETY INSTRUCTIONS WARNING Follow these basic precautions to reduce the risk of fire, electrical shock hazards or injury when operating the Freezer: • This product has been designed for using in a normal domestic environment. It is not intended for commercial use which will avoid warranty, such as supermarket, food shop, pharmacy, commercial kitchen & etc.
R600a WARNINGS NOTE: This model uses R600a flammable refrigerant in its sealed system. The following must be observed for your safety: R600a Refrigerant Warning • This appliance contains 0.043kg R600a refrigerant which is environmentally friendly, but flammable. It does not damage the ozone layer, nor does it increase the greenhouse effect. • During transportation and installation, ensure that the tubing of the refrigerant circuit is not damaged. • Leaking refrigerant can ignite and may damage the eyes.
Door reversal instruction There is no spare parts required for door reversal job. The following tool is required, flat screwdriver, phillips screwdriver, adjustable spanner, socket wrench and 8mm socket. 1. Make sure the power cable is unplugged. 2. Remove the hinge cover with a flat screwdriver, remove the three screws that hold the upper hinge on the door, then remove the upper hinge. 3. Lift up the door and remove it from the cabinet, keep it on a stable position. 4.
11. Remove the screw that secures the hinge screw hole cover from the top left side of the cabinet and put it on the right side. 12. Secure the upper hinge with the three screws. Before you tighten the upper hinge screws, make sure the door is level with the cabinet and rubber gasket has a good seal. 13. Install the hinge cover over the hinge on the top left side of the cabinet. 14. Remove the left screw caps and screws in handle, remove the right hole plugs. 15.
INSTALLATION INSTRUCTIONS Before Using the Freezer • • • Remove the exterior and interior packing. Before connecting the Freezer to a power source, let the unit stand upright for approximately 4 hours to mitigate the possibility of a malfunction in the cooling system from improper handling during transportation. Clean the interior surface with warm water using a soft cloth.
OPERATING INSTRUCTIONS TEMPERATURE CONTROL PANEL The freezer has temperature control panel on the top. Temperature control key: Press the set key to adjust temperature setting. Keep pressing until it reaches desired temperature and the number will flashing on display panel. Wait for few seconds, it will be light up stable and setting is changed properly. -18 is recommend for normal use environment. Temperature adjustment range:-16~-24。 The digital display is cycled as follows: -16→-…→-24→ -16.
Door open alarm If any door is opened for more than 3 minutes, buzzer alarm will be continuously beeping. It can be stopped by pressing key button, but it will be restored after 3 minutes if the door keeps opening. The alarm will stop when the doors are closed properly. Fault alarm When the alarm indicator keeps flashing (with the corresponding indicator light of “-16, 20, -24, or fast freezing” flickering simultaneously), it indicates fault with the refrigerator. Please contact customer service centre.
Repositioning and Relocating the Freezer • • • • • Unplug the power cord from the wall outlet. Remove all the food and drinks. Securely tape down all loose items inside your Freezer. Tape the doors to be closed securely. It is recommended that the Freezer stays in the upright position during transportation. But if it is laid down for transport purpose, please lift it up immediately after the job is done. Please wait for at least 24 hours before putting the power.
Popping or cracking sound when compressor comes on. Metal parts undergo expansion and contraction, as in hot water pipes. This is normal. Sound will level off or disappear as Freezer continues to run. Bubbling or gurgling sound, like water boiling. Refrigerant (used to cool Freezer) is circulating throughout the system. This is normal operation. Check the Freezer is on a level/even surface. Freezer rocks on the floor when it is moved slightly. Be sure floor can adequately support Freezer.
Customer Service 1300 796 688 www.chiq.com.au c Changhong Electric (Australia) P/L all rights reserved.
