Town & Country 2010 OWNER’ S MANUAL I nf or mat i onPr ov i dedby :
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I nf or mat i onPr ov i dedby :
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number .............. 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle.
INTRODUCTION 5 1 I nf or mat i onPr ov i dedby :
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
I nf or mat i onPr ov i dedby :
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 䡵 Remote Starting System — If Equipped . . . . . . . 27 ▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . 12 ▫ How To Use Remote Start . . . . . . . . . . . . . . . 27 䡵 Sentry Key威 . . . . . . . . . . . . . . . . . . . . . . . . . . 14 䡵 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 ▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Power Sliding Side Door — If Equipped . . . . . 42 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . 67 ▫ Sliding Side Door Child Protection Lock . . . . . 46 ▫ Supplemental Restraint System (SRS) Airbags . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 䡵 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 ▫ Power Liftgate — If Equipped . . . . . . . . . . . . 49 䡵 Occupant Restraints . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Restraining Infants And Small Children With Seat Delete Feature (Commercial Vehicles Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 䡵 Engine Break-In Recommendations . . . . . . . . . 100 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . 101 11 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . 101 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the Key Fob into the ignition switch with either side up. Wireless Ignition Node (WIN) The Wireless Ignition Node (WIN) operates similarly to an ignition switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. 2 The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead. The emergency key is also for locking the lower glove compartment. You can keep the emergency key with you when valet parking.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Power window switches will also remain active for up to 90 seconds after the ignition switch has been turned to LOCK, depending upon the accessory delay setting. Opening the front door will cancel this feature. WARNING! NEVER leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the Key Fob in the ignition.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE vehicle can be used to start and operate the vehicle. The system will shut the engine off in two seconds if an invalid Key Fob is used to start the engine. 15 CAUTION! The Sentry Key威 Immobilizer system is not compatible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! Always remove the Key Fobs from the vehicle and lock all doors when leaving the vehicle unattended. Customer Key Programming Programming Key Fobs or RKE transmitters may be performed at an authorized dealer. General Information The Sentry Key威 system complies with FCC rules Part 15 At the time of purchase, the original owner is provided and with RSS-210 of Industry Canada. Operation is with a four-digit Personal Identification Number (PIN).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE lamps and/or turn signals will flash and Vehicle Security Light will flash repeatedly and the horn will sound. For an additional 15 minutes, only the headlights, park lamps and/or turn signals and Vehicle Security Light will flash. The engine will run only if a valid key is used to start the vehicle.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Vehicle Security Alarm remains armed during liftgate entry. Pressing the liftgate button will not disarm the Vehicle Security Alarm. If someone enters the vehicle through the liftgate and opens any door the alarm will sound. exterior lights will flash, the horn will sound. If this occurs, disarm the Vehicle Security Alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: Inserting the Key Fob with RKE transmitter into the ignition switch disables all buttons on that RKE transmitter; however, the buttons on the remaining RKE transmitters will continue to work. Driving at speeds 5 mph (8 km/h) and above disables all RKE transmitter • The Illuminated Entry System will not operate if the buttons for all RKE transmitters. dimmer control is in the extreme downward position.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE (optional), power sliding doors, Remote Start feature Using the RKE Transmitter Three-button RKE transmitters will provide basic UN- (optional). Some features can be programmed to the LOCK, LOCK and PANIC functions. customers preferences. For example, flash headlights or sound horn on LOCK.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Unlock Doors and Liftgate Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s side or twice to unlock all doors and liftgate. The Illuminated Entry system also turns on. 21 1. Perform this operation while standing outside the vehicle. 2. Press and hold the LOCK button on a programmed RKE transmitter for at least 4 seconds, but no longer than 10 seconds.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the RKE transmitter while you are inside the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Vehicle Security Alarm. Remote Lock Doors and Liftgate Press and release the LOCK button on the RKE transmitter to lock all doors and liftgate. The horn will chirp once to acknowledge the signal.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Press the LOCK button on a programmed RKE transmitter for at least 4 seconds, but no longer than 10 seconds. Then, press the PANIC button while still holding the LOCK button. 3. Release both buttons at the same time. 23 Using the Panic Alarm To turn the Panic Alarm feature on or off, press and hold the PANIC button on the RKE transmitter for at least one second and release.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the liftgate is locked and is not equipped with a powered liftgate, pressing the LIFTGATE button twice will result in the liftgate becoming unlocked for 30 seconds allowing you to manually access the liftgate area. Power Open/Close Right Power Sliding Door — If Equipped Press the RIGHT Power Sliding Door button twice on the RKE transmitter within five seconds to Power Open/ Close the Right Power Sliding Door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 • For vehicles not equipped with the EVIC, perform the NOTE: Pressing the LOCK button on the RKE transmitfollowing steps: ter while you are in the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security 1. Perform this operation while standing outside the Alarm activated will cause the alarm to sound. Press the vehicle. UNLOCK button to deactivate the Vehicle Security 2.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transmitter Battery Replacement General Information The recommended replacement battery is one CR2032 This device complies with Part 15 of the FCC rules and battery. RSS 210 of Industry Canada. Operation is subject to the following conditions: NOTE: • Perchlorate Material — special handling may apply. • This device may not cause harmful interference. See: www.dtsc.ca.gov/hazardouswaste/perchlorate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE STARTING SYSTEM — IF EQUIPPED This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conveniently from outside the vehicle while still maintaining security. The system has a range of approximately 300 ft (91 m). NOTE: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Enter Remote Start Mode Press and release the REMOTE START button on the RKE transmitter twice within five seconds. The vehicle doors will lock, parking lights will flash and horn will chirp twice (if programmed). Then, the engine will start and the vehicle will remain in the Remote Start mode for a 15-minute cycle. • The engine can be started two consecutive 15-minute cycles with the RKE transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 equipped). Then, prior to the end of the 15-minute cycle, • The hood is opened insert the Key Fob into the ignition switch and turn the • The hazard switch is pressed switch to the ON position. • The shift lever is moved out of PARK NOTE: • The ignition switch must be in the ON position in • The engine is allowed to run for the entire 15-minute order to drive the vehicle.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE failed start, where the Remote Starting sequence was initiated but the engine stopped cranking without starting. After either of these conditions, or if the Vehicle Security Alarm system is alarming, or if the PANIC button was pressed, the vehicle must be reset by inserting a valid Key Fob into the ignition switch and rotating the Key Fob to the ON position, and then rotating the Key Fob back to the LOCK/OFF position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the lock plunger is rearward when you shut either side sliding door, the door will lock. Make sure the keys are not inside the vehicle before closing the door. 31 WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the key from the ignition switch, and lock your vehicle.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you press the power door lock switch while the Key Power Door Locks — If Equipped A power door lock switch is on each front door trim Fob is in the ignition, and any front door is open, the panel. Use this switch to lock or unlock the doors. power locks will not operate. This prevents you from accidentally locking your keys in the vehicle. Removing the Key Fob or closing the door will allow the locks to operate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Lock Doors Automatically — If Equipped If the Lock Doors Automatically feature is enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h).
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Fasten your seat belt. (Fastening the seat belt will The Lock Doors Automatically at 15 mph (24 km/h) cancel any chiming that may confuse you during this feature can be reactivated by repeating the above mentioned procedure or by performing the procedure in the programming procedure.) EVIC (if equipped), Personal Settings (Customer3. Place the Key Fob into the ignition. Programmable Features). 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • On vehicles equipped with the optional Electronic Vehicle Information Center (EVIC), refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information. 35 5. Within 30 seconds, press the driver’s door lock switch in the UNLOCK direction. 6. A single chime will sound to indicate the feature has been changed. 7.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows You can control either the front or rear windows using Power Vent Windows — If Equipped switches located on the driver’s door trim panel. The Switches on the driver’s door trim panel let the driver switches will operate only when the ignition switch is in operate the two vent windows from the driver’s seat. the ON or ACC position and during power accessory delay.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Power Window switches will also remain active for up to 10 minutes after the ignition switch has been turned to LOCK, depending upon the accessory delay setting. Opening a front door will cancel this feature. 2 Power Window Lockout Switch — If Equipped The driver may lock out all power windows by depressing the bar switch just below the power window switches.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front Passenger Power Window Switch There is a single switch on the front passenger’s door trim panel which operates the passenger door window and locks and unlocks all doors. The switch will operate only when the ignition switch is in the ON or ACC position and during power accessory delay.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Sliding Side Door Power Window Switch — If Equipped Second row passengers may open and close the sliding door window by a single switch on the door handle assembly. 2 The switches will operate only when the ignition switch is in the ON or ACC position and during power accessory delay. NOTE: The switches will not operate if the driver has activated the Power Window Lockout.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto-Down Feature — If Equipped The front window switches may be equipped with an Auto-Down feature. Press the window switch past the detent, release, and the window will go down automatically. To stop the window from going all the way up during the Auto Up operation, push down on the switch briefly. To close the window part way, lift the window switch to the first detent and release when you want the window to stop.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Wind Buffeting Wind buffeting can be described as the perception of There is no anti-pinch protection when the window pressure on the ears or a helicopter-type sound in the is almost closed. To avoid personal injury be sure to ears. Your vehicle may exhibit wind buffeting with the clear your arms, hands, fingers and all objects from windows down, or the sunroof (if equipped) in certain open or partially open positions.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To keep your door operating properly, observe the fol- NOTE: The left side sliding door cannot be opened while the fuel door is open. This feature operates only lowing guidelines: when the sliding door is fully closed prior to opening the • Always open the door smoothly. fuel door. • Avoid high impacts against the door stop when openPower Sliding Side Door — If Equipped ing the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 There are power sliding side door switches located on the trim panel just in front of the power sliding door for the rear seat passengers and in the overhead console for the driver and passengers. Pressing the switch once will open the power sliding door. When the door is fully open pressing the switch a second time will close the door. 2 NOTE: The power sliding side door must be unlocked before the power sliding door switches will operate.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE door switch is pressed. To close the door, wait until it To avoid unintentional operation of the power sliding is fully open and then press the switch again. doors from the rear seats, press the power sliding door master lock button, located in the overhead console, to • If the power sliding door encounters multiple obstrucdisable the switches and handles for the rear seat passentions within the same cycle, the system will automatigers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 The Sliding Side Door Open Flash can be enabled or When the power sliding door master lock switch is in the ON position, the power sliding side door may not be disabled by performing the following procedure: opened or closed by pressing the switch located on the 1. Place the Key Fob in the ignition switch. trim panel just in front of the sliding door or activating 2. Cycle the ignition switch ON/LOCK five times ending the inside power sliding door handle.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sliding Side Door Child Protection Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a Child Protection Door Lock system. NOTE: When the Child Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. To Engage the Child Protection Door Lock 1. Open the sliding side door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When the Child Protection Door Lock system is engaged, (even if the inside door lock is in the unlocked position) the door can be opened only by using the outside door handle, the RKE transmitter, the switches on the overhead console or the switches located on the trim panel just in front of the power sliding door.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the liftgate, press the liftgate release handle NOTE: • After setting the Child Protection Door Lock system, located on the underside of the license plate bar and pull always test the door from the inside to make certain it the liftgate open with one fluid motion. is in the desired position. • The power sliding side door switches will not open the power sliding doors if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the liftgate is locked and is not equipped with the power liftgate feature, pressing the button on the RKE transmitter will result in the liftgate becoming unlocked for 30 seconds allowing you to manually access the liftgate area. 2 Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the Remote Keyless Entry (RKE) transmitter.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power liftgate may be closed by pressing the button, When the RKE transmitter button is pressed and the located in the upper left trim in the liftgate opening. Flash Lights feature is enabled, the tail lights will flash to Pushing once will only close the liftgate. This button signal that the liftgate is opening or closing. cannot be used to open the liftgate. WARNING! During power operation, personal injury or cargo damage may occur.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • There are also pinch sensors attached to the side of the liftgate opening. Light pressure anywhere along these strips will cause the liftgate to return to the open position. 51 (62°C). Be sure to remove any buildup of snow or ice from the liftgate before pressing any of the power liftgate buttons.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Gas props support the liftgate in the open position. • Supplemental Seat-Mounted Side Airbags (SAB) — if However, because the gas pressure drops with temperaequipped ture, it may be necessary to assist the props when • An energy-absorbing steering column and steering opening the liftgate in cold weather.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 NOTE: The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Please pay close attention to the information in this section.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE you under normal conditions. However, in a collision the belt will lock and reduce the risk of you striking the inside of the vehicle or being thrown out. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. WARNING! • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. 57 4.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job properly. In a collision, it could even cut into you. Be sure the belt is straight.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Pull the strap down and secure the small latch plate of simultaneously pushing down on the anchorage assemthe lap belt into the small buckle until you hear a “click”. bly. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. When the belt is long enough to fit, insert the large latch plate into the buckle until you hear a “click.” The retractor should withdraw any slack in the belt.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. How To Engage The Automatic Locking Mode Automatic Locking Retractors (ALR) Mode — If Equipped In this mode, the shoulder belt is automatically prelocked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners — If Equipped The seat belts for both front seating positions may be equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts. NOTE: The Active Head Restraints (AHR) may or may not deploy in the event of a front or side impact. However if during a front impact, a secondary rear impact occurs, the AHR may deploy based on the severity and type of the impact.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 1. Grasp the deployed AHR from the rear seat. CAUTION! All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. NOTE: For more information on properly adjusting and positioning the head restraint, refer to “Adjusting Active Head Restraints” in “Understanding The Features Of Your Vehicle”.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 3 — Final Downward Movement To Engage Locking Mechanism 1 — Downward Movement 2 — Rearward Movement 4. The AHR front soft foam and trim half should lock into the back decorative plastic half.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Enhanced Seat Belt Use Reminder System (BeltAlert姞) If the driver’s or front passenger’s (if equipped with belt alert) seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert威) will alert the driver or front passenger to buckle the seat belt. The driver should also instruct all other occupants to buckle their seat belts.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE front passenger seat is unoccupied. The BeltAlert威 warning system may be triggered when an animal or heavy object is on the front passenger seat or when the seat is folded flat (if equipped). It is recommended that pets be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts and cargo is properly stowed. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 NOTE: Although BeltAlert威 has been deactivated, the Seat Belt Reminder Light will continue to illuminate while the driver’s seat belt remains unbuckled or retracted. Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Restraint System (SRS) - Airbags This vehicle has Advanced Front Airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s Advanced Front Airbag is mounted in the center of the steering wheel. The passenger’s Advanced Front Airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 The Advanced Front Airbags have a multistage inflator NOTE: design. This allows the airbag to have different rates of • Airbag covers may not be obvious in the interior trim; but they will open during airbag deployment. inflation based on the severity and type of collision. This vehicle may be equipped with driver and/or front • After any collision, the vehicle should be taken to an authorized dealer immediately.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Supplemental Seat-Mounted Side Airbags (SAB) the second stage determines whether the output force is low, medium, or high. If a low output is sufficient to meet • Supplemental Side Airbag Inflatable Curtains (SABIC) the need, the remaining gas in the inflator is expended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 WARNING! (Continued) • Do not drill, cut or tamper with the knee bolster in any way. • Do not mount any accessories to the knee bolster such as alarm lights, stereos, citizen band radios, etc. Supplemental Seat-Mounted Side Airbags (SAB) — If Equipped Supplemental Seat-Mounted Side Airbags provide enhanced protection to help protect an occupant during a side impact.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped SABIC airbags may offer side-impact and vehicle rollover protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries. The curtains deploy downward, covering both windows on the impact side.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Knee Impact Bolsters The Knee Impact Bolsters help protect the knees of the driver and the front passenger, and position front occupants for the best interaction with the Advanced Front Airbags. 73 WARNING! Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger Advanced Front Airbag. An airbag deployment can cause severe injury or death to infants in that position.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If a child from 1 to 12 years old (not in a rear facing child seat) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint. (Refer to “Child Restraints”) If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under ⬙If You Need Assistance⬙ in this manual.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Being too close to the steering wheel or instrument panel during Advanced Front Airbag deployment could cause serious injury, including death. Airbags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • Side airbags also need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Advanced Front Airbags may deploy in crashes with in the ACC position, or not in the ignition, the airbag little vehicle front-end damage but that produce a severe system is not on and the airbags will not inflate. initial deceleration. The ORC contains a backup power supply system that The side airbags will not deploy in all side collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the Airbag Warning Light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the airbag system immediately.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE triggered, releasing a quantity of non-toxic gas. The inflating side airbag exits through the seat seam into the space between the occupant and the door. The side airbags fully inflate in about 10 milliseconds. The side airbag moves at a very high speed and with such a high force, that it could injure you if you are not seated properly, or if items are positioned in the area where the side airbag inflates. This especially applies to children.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System In the event of an impact causing airbag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of the event the ORC will determine whether to have the Enhanced Accident Response System perform the following functions: • • • • 79 NOTE: Front and/or side airbags will not deploy in all collisions. This does not mean something is wrong with the airbag system.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE airbag inflation. These airborne particles may irritate Maintaining Your Airbag System the skin, eyes, nose, or throat. If you have skin or eye WARNING! irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation • Modifications to any part of the airbag system continues, see your doctor. If these particles settle on could cause it to fail when you need it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not attempt to modify any part of your advanced airbag system. The airbag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any advanced airbag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The airbags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In the event that an investigation is undertaken by Chrysler Group LLC (regardless of initiative), the company or its designated representative will first obtain permission of the appropriate custodial entity for the vehicle (usually the vehicle owner or lessee) before accessing the electronic data stored, unless ordered to image the data by a court with legal jurisdiction (i.e., pursuant to a warrant).
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Pedal position • And other parameters configuration depending on vehicle Integrated Child Booster Seat — If Equipped The Integrated Child Booster Seat (if equipped) is located in each second-row passenger seat. The booster seat is designed for children weighing between 48 and 85 lbs (22 and 39 kg) and between 47 in (119 cm) and 57 in (145 cm) tall. The booster seat is designed to raise the child high enough to use the vehicle lap and shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 WARNING! (Continued) • The swivel seat should be locked in the forwardfacing position when using the booster seat with the vehicle in motion. • Be certain that the seat cushion is locked securely into position before using the seat. Otherwise, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat cushion could cause serious injury. 2.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Once the seat belt is long enough to fit properly, insert Integrated Child Seat — If Equipped Operating instructions for the second row bench seat the latch plate into the buckle until you hear a “click.” with Integrated Child Seat are included with the seat. If 6. To remove the slack from the lap belt, pull upward on the instructions are not with the seat or in the Owner’s the shoulder portion of the seat belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To obtain Integrated Child Seat replacement instructions: Refer to “Publication Order Forms” in ⬙If You Need Consumer Assistance⬙ and specify publication number 81–016–8050 when ordering. Child Restraints Everyone in your vehicle needs to be buckled up all the time, including babies and children. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Safety experts recommend that children ride WARNING! rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types Rearward-facing child seats must NEVER be used in of child restraints can be used rearward-facing: infant the front seat of a vehicle with a front passenger carriers and convertible child seats. Both types of child airbag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never place any child seat, booster seat, or infant carrier in the Swivel ’n Go seat while it is in the rearward-facing position. The swivel seat should be locked in the forward position when using any child seat, booster seat, or infant carriers, with the vehicle in motion. Failure to do so could result in serious injury or even death.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. If this doesn’t help, move the child to the center rear seating position and use both the lap and shoulder belt. Never allow a child to put the shoulder belt under an arm or behind their back.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips on getting the most out of your child restraint: 91 shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight; however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Buckle the child into the seat according to the child installed as described here. Again, carefully follow the installation instructions that are provided with the child restraint manufacturer’s directions. restraint system. • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. In general, you will first loosen the adjusters on the lower Don’t leave it loose in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 third row fold-in-floor seats are equipped with a child restraint tether anchor at the center seating position. WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If your child restraint seat is not LATCH-compatible, 4. Tighten the lower attachment strap while firmly pushinstall the restraint using the vehicle seat belts. ing the child restraint rearward and downward into the vehicle seat. Remove all slack in the lower attachment Installing the Lower Attachments: straps. Reference the child restraint instructions for infor1. The vehicle lower anchorages are round bars located mation on properly removing slack.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Installing the Top Tether Strap (with either Lower Anchors or Vehicle Seat Belt): 1. Route the top tether strap under the adjustable head restraint between the steel posts. 2 2. Provide enough slack (reference child restraint instructions) for the tether strap to reach the tether anchor located near the bottom of the seat back. 3. Clip tether hook to tether anchor. Ensure that the hook is firmly engaged and secure. 4.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. then allow the belt to retract into the retractor. For additional information on ALR, refer to “Automatic Locking Mode”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet could be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. 97 WARNING! NEVER carry a child in a rear facing infant carrier in a vehicle without rear seats.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This vehicle is equipped with a child restraint tether • The rearward-facing infant carrier is for babies weighanchor located on the lower rear of the front passenger ing up to about 20 lbs (9 kg), and less than one year seat. Use this tether anchor to secure only forwardold. THIS TYPE OF SEAT CANNOT BE USED IN A facing child restraints equipped with an upper tether VEHICLE EQUIPPED WITH THE REAR SEAT DEstrap. LETE FEATURE (Commercial Vehicles Only).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Children more than 40 lbs (18 kg) should be secured in the passenger seat in a child restraint or beltpositioning booster seat with the seat adjusted to the rear most position. Older children who do not use child restraints or belt-positioning booster seats should ride properly buckled in the passenger seat with the seat adjusted to the rearmost position. Never allow children to slide the shoulder belt behind them or under their arm. 99 3.
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! The vehicle tether anchor is designed to be used with a child restraint only. It should not be used for any other purpose. Before use, inspect the tether anchor strap for nicks, abrasions, discoloration, and loose threads. If these or any other condition that might affect the performance of the strap is observed, DO NOT USE that strap. Personal injury may result. Contact your authorized dealership for a replacement part.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS 101 WARNING! (Continued) Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust Gas WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If it is necessary to sit in a parked vehicle with the engine inspect the exhaust system each time the vehicle is raised running, adjust your heating or cooling controls to force for lubrication or oil change. Replace as required. outside air into the vehicle. Set the blower at high speed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Floor Mat Safety Information Always use floor mats designed to fit the foot well of your vehicle.
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Check mounting of mats on a regular basis. Always properly reinstall and secure floor mats that have been removed for cleaning. • Always make sure that objects cannot fall into the driver foot well while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • If required, mounting posts must be properly installed, if not equipped from the factory.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 Door Latches Check for positive closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately.
I nf or mat i onPr ov i dedby :
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 ▫ Inside Day/Night Mirror — If Equipped . . . 112 ▫ Automatic Dimming Mirror — If Equipped . . 113 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . 113 ▫ Driver’s Automatic Dimming Mirror — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 114 ▫ Outside Mirror Folding Feature . . . . . . . . . . 114 ▫ Power Mirrors — If Equipped . . . . . . . . . . .
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 ▫ Third Row Power Recline — If Equipped . . . 149 ▫ Manual Front And Second Row Seat Adjuster . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 䡵 Driver Memory Seat — If Equipped . . . . . . . . 153 ▫ Manual Reclining Seats — If Equipped . . . . . 128 ▫ Setting Memory Positions And Linking RKE Transmitter To Memory . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 ▫ Headlight Delay — If Equipped . . . . . . . . . . 163 䡵 Adjustable Pedals — If Equipped . . . . . . . . . . 172 ▫ Daytime Running Lights 䡵 Electronic Speed Control — If Equipped . . (Canada/Fleet Vehicles Only) . . . . . . . . . . . . 164 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . ▫ Front Fog Lights — If Equipped . . . . . . . . . . 164 ▫ To Set At A Desired Speed . . . . . . . . . . . ▫ Battery Protection . . . . . . . . . . . . . . . . . .
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Service Parksense威 . . . . . . . . . . . . . . . . . . . 183 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 ▫ Cleaning Parksense威 . . . . . . . . . . . . . . . . . . 183 ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . 197 ▫ Parksense威 System Usage Precautions . . . . . . 183 ▫ General Information . . . . . . . . . . . . . . . . . . 197 䡵 Parkview威 Rear Back Up Camera — If Equipped . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 ▫ Door Trim Panel Storage . . . . . . . . . . . . . . . 209 䡵 Console Features . . . . . . . . . . . . . . . . . . . . . . 215 ▫ Driver Seatback Storage — If Equipped . . . . 210 ▫ Basic Console . . . . . . . . . . . . . . . . . . . . . . . 215 ▫ Umbrella Holder . . . . . . . . . . . . . . . . . . . . . 210 ▫ Premium Console — If Equipped . . . . . . . . . 216 ▫ Second Row Floor Storage Bins . . . . . . . . . . 211 䡵 Rear Window Features . . . . . . . . .
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated. 113 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in an outside convex mirror will look smaller and farther away than they really are. Relying too much on side convex mirrors could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in a side convex mirror. Outside Mirror Folding Feature All outside mirrors are hinged and may be moved either forward or rearward to resist damage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Driver’s side power mirror preselected positions can be controlled by the optional Driver Memory Seat Feature. Refer to “Driver Memory Seat” in “Understanding the Features of Your Vehicle” for further information. Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE when the vehicle is shifted out of REVERSE position. Illuminated Vanity Mirrors — If Equipped Each stored memory setting will have an associated Tilt An illuminated vanity mirror is located on the sun visor. To use the mirror, rotate the sun visor down and swing Mirrors in Reverse position. the mirror cover upward. The lights turn on automatiNOTE: The Tilt Mirrors in Reverse feature is not encally. Closing the mirror cover turns off the lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE BLIND SPOT MONITORING — IF EQUIPPED The Blind Spot Monitoring (BSM) system uses two radarbased sensors, located inside the rear bumper fascia, to detect Highway licensable vehicles (automobiles, trucks, motorcycles etc.) that enter the blind spot zones from the rear/front/side of the vehicle.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The BSM system detection zone DOES NOT change if your vehicle is towing a trailer. Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change. If the trailer or other object (i.e., bicycle, sports equipment) extends beyond the side of your vehicle, this may result in the BSM warning light remaining illuminated the entire time the vehicle is in a forward gear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 The BSM system notifies the driver of objects in the The BSM system can also be configured to sound an detection zones by illuminating the BSM warning light audible (chime) alert and mute the radio to notify the located in the outside mirrors. driver of objects that have entered the detection zones. Refer to “Modes Of Operation” for further information.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Overtaking Traffic If you pass another vehicle slowly (with a relative speed less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 10 mph (16 km/h), the warning light will not illuminate.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc. However, occasionally the system may alert adjacent lanes. on such objects. This is normal operation and your vehicle does not require service.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicyclists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicles mirrors, glance over your shoulder, and use your turn signal before changing lanes. Failure to do so can result in serious injury or death.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. Modes Of Operation Three selectable modes of operation are available in the Electronic Vehicle Information Center (EVIC).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime will also be sounded. Whenever a turn signal and detected object are present on the same side at the same time, both the visual and audio alerts will be issued. In addition to the audible alert the radio (if on) will also be muted.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE VOICE COMMAND — IF EQUIPPED Voice Command can be initiated by pressing the VR located on the radio or steering wheel button controls (if equipped). Refer to “Voice Command” in the Uconnect™ Phone User Manual located on the DVD for further details. SEATS Seats are a primary part of the Occupant Restraint System of the vehicle. They need to be used properly for safe operation of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Front And Second Row Seat Adjuster The adjusting bar is located under the front of the seat. Pull the bar upward and move the seat to the desired position. Release the bar to lock the seat into position. Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. 127 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Reclining Seats — If Equipped The recliner control lever is on the outboard side of the seat. To recline, lean forward slightly, lift the lever, then push back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. Using body pressure, lean forward and rearward on the seat to be sure the seatback has latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Lumbar Adjust Lever — If Equipped The lumbar adjustment lever is located on the outboard side of the seat. To increase the support, rotate the lever downward. To decrease the support, rotate the handle upward. 129 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Eight–Way Power Seats — If Equipped The power seat switches are located on the outboard side of the seats. The front switch controls the up/down, forward/rearward and tilt adjustment. The rear switch controls the recline adjustment of the seatback. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Heated Seats — If Equipped This feature heats the front driver and passenger seats. The controls for front heated seats are located on the center instrument panel area. After turning the ignition ON, you can choose from High, Low, or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low, and none for Off. Press the switch once to select High-level heating.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. • Do not place anything on the seat that insulates against heat, such as a blanket or cushion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 3 Adjusted Head Restraint Push Button To raise the head restraint, pull upward on the head restraint (on some models, you may need to press the push button). To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. Active Head Restraint — If Equipped For comfort the Active Head Restraints can be tilted forward and backward.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head. Active Head Restraint (Tilted) Active Head Restraint (Normal Position) NOTE: • The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your authorized dealer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In the event of deployment of an Active Head Restraint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things to Know Before Starting Your Vehicle” for further information. WARNING! • Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Stow ’n Go姞 Seating — If Equipped On vehicles equipped with Stow ’n Go威 seating, the second and third row seats may be folded into the floor for convenient storage. To Fold Second Row Seats 1. Move the front seat fully forward. 2. Lower the head restraints and raise the armrests on the second row seat. 3. Slide the storage bin locking mechanism to the ⬙LOCK⬙ position and then pull up on the storage bin latch to open the cover.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 4. Pull up on the seatback recliner lever located on the 5. Pull rearward on the release strap located at the rear of outboard side of the seat and fold the seatback down. To the seat and tumble the seat forward into the storage bin. assure the seatback is latched in the folded position, additional downward pressure on the seatback may be required when folding. 3 Second Row Seat Release Strap 6. Close the storage bin cover.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Pull up on the handle to lift the seat out of the storage bin and push the seat rearward to latch the seat anchors. CAUTION! The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. WARNING! In an accident, serious injury could result if the seat storage bin covers are not properly latched. • DO NOT drive the vehicle with the storage bin covers open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 To tilt the seat, pull forward on the release strap located on the front of the seat between the seatback and seat cushion and tilt the seat fully forward. To return the seat to its upright position, push rearward on the seatback until it latches. Always ensure that it is fully latched. Second Row Seatback Release Lever 4.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Seats are removable WARNING! In the event of a collision you could be injured if the seat is not fully latched. Swivel ’n Go™ Premium Seating — If Equipped Premium second row Swivel ’n Go™ Seating features include: • A table that installs between the second and third row seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 WARNING! When the seatback release handle is lifted, the seatback will rotate forward. To avoid injury, if you are not seated in the seat, stay clear from the area in the path of the rotating seatback. 3 To swivel the seat: Pull the lower handle on the outboard side of the seat and push the side of the seatback to begin rotation. Once the seat begins to rotate, the handle may be released.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Removing Swivel ’n Go™ Premium Seating — If Equipped WARNING! Failure to comply with the following conditions could result in serious injury or even death: • NEVER place any child seat or infant carrier in the Swivel ’n Go™ seat while it is in the rearward facing position. • The swivel seat should be locked in the forward position when using any child seat or infant carriers, with the vehicle in motion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 3. From behind the seat, lift up on the rear of the seat When reinstalling the seat, make certain to lower the cushion while pulling the seat in a rearward direction. release handle to ensure the seat is latched securely. 4. Remove the seat from vehicle through the liftgate. Rollers are part of the seat frame and will ease the removal process. 5. Lower the release handle located at the bottom front edge of the seat.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Open the floor storage cover in front of the second row Swivel ’n Go™ Premium Seating Table — If seats. Equipped The Swivel ’n Go™ Seating Table consists of an easily assembled post and top. Table and Leg Storage Second Row Seating and Table 2. Remove the pole and table top by loosening the hook and loop straps. The table and leg are stored beneath the floor when not in 3. Swivel the second row seats so they are facing the rear. use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 4. Insert pole into base by aligning the lock button into 5. Twist the pole in a clockwise rotation until it stops. notch of the base. NOTE: You will hear an audible “click” when the lock button engages the base. 6. Place the table top over the installed pole aligning with the mating feature of the underside of the table top. Apply pressure on the table top and press downward. NOTE: You will hear an audible “click” when the table latch engages the pole.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To separate the table top from the pole, follow these steps: WARNING! Failure to comply with the following conditions could result in serious injury or even death: • DO NOT install the table while vehicle is in motion. • NEVER drive the vehicle with only the pole installed. • DO NOT place heavy or sharp objects on table. • DO NOT place liquid drinks on the table, use available cupholders.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 2. Pull horizontally on the latch to activate the release 6. Place the pole on the underside of the table top and from the pole. secure with the hook and loop straps. 3. While pulling on the latch, pull upward to remove the 7. Once the pole and table top are secured, you may table top from the pole. place them in the floor storage bin in front of the second row seats.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second Row Bench Seat — If Equipped While the bench seat does not stow in the floor, it is removable for added cargo space. Release levers are located on the rear leg assemblies, near the floor. To remove the seat, squeeze each release handle and rotate downwards to deploy the wheels. A lock indicator button pops up when the seat is unlocked. The seat assembly can now be removed from the vehicle and moved on its Easy Out威 Rollers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 WARNING! If not properly latched, the bench seats could become loose. Personal injuries could result. After reinstalling these seats, be sure the red indicator button on the release handles return into the handles. 3 Third Row Power Recline — If Equipped The power recline feature, located on the side of the seat cushion, adjusts the seatback angle forward/rearward for occupant comfort.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The switch is only functional when the liftgate is open Left and right third row seats can be folded individually and the vehicle is in PARK. or together. The third row power folding seat adjusts to the following positions using the switch bank located on the left rear trim panel: One Touch Folding Seat Third Row The rear switch bank allows multiple power folding and unfolding positions for the third row seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 2. Pull release strap marked “1” located on the rear of the NOTE: • Disconnect the center shoulder belt from the small seat to lower the seatback. buckle and lower the head restraints before attempting 3. Pull release strap marked “2” to release the anchors. to fold/stow the power third row seats. • To abort seat operation while seat is in motion, press a different seat position selector switch to stop the seat.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Unfold Third Row Seats Tailgate Mode 1. Pull up on the assist strap to lift the seat out of the 1. Pull release strap “2”, then pull release strap “3” to storage bin and push the seat forward until the anchors rotate the entire seat rearward. latch. 2. Pull release strap marked “1” to unlock the recliner. 3. Pulling strap “3” releases the seatback to return to its full upright position. 4. Adjust the head restraint to the desired position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 WARNING! To avoid serious injury or death, NEVER operate the vehicle with occupants in the third row seat while in the tailgate mode. 3 DRIVER MEMORY SEAT — IF EQUIPPED The Memory Buttons 1 and 2 on the driver’s door panel can be programmed to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station preset settings.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Turn on the radio and set the radio station presets (up to 10 AM and 10 FM stations can be set). Setting Memory Positions and Linking RKE Transmitter to Memory NOTE: Each time the SET (S) button and a numbered 6. Turn the ignition switch to the OFF position and button (1 or 2) is pressed, you erase the memory settings remove the key. for that button and store a new one. 7. Press and release the SET (S) button located on the 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 11. Select ⬙Remote Linked to Memory⬙ in the Electronic Vehicle Information Center (EVIC) and enter “Yes”. Refer to “Electronic Vehicle Information Center (EVIC)/ Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information. 155 To recall the memory setting for driver two, press MEMORY button 2 on the driver’s door or the UNLOCK button on the RKE transmitter linked to Memory Position 2.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Press and release the memory SET (S) button located Customer-Programmable Features⬙ in “Understanding on the driver’s door. A chime will sound signaling that Your Instrument Panel” for further information. you are in the memory set mode. Easy Entry/Exit Seat (Available with Memory Seat 4. Within five seconds, press and release MEMORY ONLY) button 1 on the driver’s door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When you remove the key from the ignition switch the driver seat will move to a position 0.3 in (7.7 mm) forward of the rear stop if the driver seat position is between 0.9 – 2.7 in (22.7 – 67.7 mm) forward of the rear stop. The seat will return to its previously set position when you insert the key into the ignition switch and turn it out of the LOCK position. • The Easy Entry/Easy Exit feature is disabled when the driver seat position is less than 0.9 in (22.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Move to the front of the vehicle and look inside the center of the hood opening. Locate, then push the safety catch lever to the right, while raising the hood at the same 1. Pull the hood release lever located on the instrument time. panel, below the steering column. TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. Hood Release Safety Catch Location Use the hood prop rod to secure the hood in the open position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 12 in (30 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. 159 LIGHTS All of the lights, except the Hazard Warning lights, headlight high beams and flash-to-pass, are controlled by switches to the left of the steering column on the instrument panel.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lighting Dome Light Positions Interior lights are turned on when a door or liftgate is Rotate the dimmer control completely opened, the Remote Keyless Entry (RKE) transmitter is upward to the second detent (extreme activated, or when the dimmer control is moved to the top position) to turn on the interior extreme top. lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parade Mode (Daytime Brightness Feature) Rotate the dimmer control to the first detent. This feature brightens the odometer, radio and overhead displays when the parking lights or headlights are on. 161 Halo Lights — If Equipped Halo lights are strategically placed soft lighting that help to illuminate specific areas to aid the occupants in locating specific features while driving at night.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To change the brightness of the instrument panel lights, rotate the dimmer control up or down. Automatic Headlights — If Equipped This system automatically turns your headlights on or off based on ambient light levels. To turn the system on, turn the headlight switch to the extreme counterclockwise position aligning the indicator with the “A” on the headlight switch. When the system is on, the Headlight Time Delay feature is also on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights On With Wipers — If Equipped When your headlights are in the Automatic mode and the engine is running, the headlights will automatically turn on when the wiper system is also turned on. Headlights on when windshield wipers are on may be found on vehicles equipped with an automatic headlight system. Refer to “Electronic Vehicle Information Center (EVIC)/ Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (Canada/Fleet Vehicles Only) The headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except PARK. This provides a constant lights on condition until the ignition is turned OFF. The lights illuminate at less than 50% of normal intensity. If the parking brake is applied, the Daytime Running Lights (DRL) will turn off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Multifunction Lever The multifunction lever is located on the left side of the steering column.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Turn Signal Warning If the vehicle electronics sense that the vehicle has traveled at over 18 mph (29 km/h) for approximately 1 mile (1.6 km) with the turn signals on, a chime will sound to alert the driver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 2. Rotate the headlight switch counterclockwise to the NOTE: Broken, muddy or obstructed headlights and taillights of vehicles in the field of view will cause AUTO (A) position. headlights to remain on longer (closer to the vehicle). 3. Push the multifunction lever away from you to switch Also, dirt, film and other obstructions on the windshield the headlights to the high beam position.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper switch is turned off and the blades cannot return to the off position, damage to the wiper motor may occur. 1. Mist, Front Wiper and Washer Press the end of the multifunction lever inward to the first detent and release to clear the windshield.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Intermittent, Low and High Speed Wipers Use the intermittent wipers when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. Rotate the end of the multifunction lever to the first detent position, then turn the end of the multifunction lever to select the desired delay interval. The delay can be regulated from approximately two seconds, to a maximum of 20 seconds between cycles.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver. This feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of the five intermittent wiper sensitivity settings to activate this feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 The Rain Sensing system has protective features for the • Remote Start Mode Inhibit — On vehicles equipped wiper blades and arms. It will not operate under the with Remote Starting system, Rain Sensing wipers are following conditions: not operational when the vehicle is in the remote start mode.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To tilt the column, push the lever downward to the unlocked position. Move the steering column up or down, as desired. Pull the lever upward to the locked position to lock the steering column firmly in place. Tilt Steering Column Lever 1 — Locked Position 2 — Unlocked Position WARNING! Do not adjust the steering column while driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 • The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control System is on. The following messages will be displayed on vehicles equipped with the Electronic Vehicle Information System (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident. Always adjust the pedals while the vehicle is parked. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph (40 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. 175 WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the Electronic Speed Control system off when you are not using it.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Deactivating Electronic Speed Control A soft tap on the brake pedal or pulling the Electronic Speed Control lever (CANCEL) toward you will deactivate the Electronic Speed Control without erasing the set speed memory. Pushing the ON/OFF button to the OFF position or turning OFF the ignition erases the set speed memory. RESUME ACCEL position, the set speed will continue to increase until the lever is released, then the new set speed will be established.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Accelerating To Pass Press the accelerator as you normally would. When the pedal is released, the vehicle will return to the set speed. NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal. 177 WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense威 will remember the last system state (enabled The sensors can detect obstacles from approximately or disabled) from the last ignition cycle when the ignition 12 in (30 cm) up to 79 in (200 cm) from the rear fascia/bumper in the horizontal direction, depending on is changed to the RUN/ON position. the location, type and orientation of the obstacle. ParkSense威 can be active only when the shift lever is in REVERSE.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 The ParkSense威 Warning Display is located in the Instru- ParkSense姞 Display ment cluster’s EVIC display. It provides both visual and When the vehicle is in REVERSE, the warning display audible warnings to indicate the distance between the will turn ON indicating the system status. rear fascia/bumper and the detected obstacle.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The system will indicate a detected obstacle by showing three solid arcs and will produce a 1⁄2 second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 3 Fast Tone Continuous Tone The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING DISPLAY DISTANCES DISPLAY MESSAGE OBSTACLE DISTANCE FROM: REAR CORNERS REAR CENTER ARC’s AUDIBLE SIGNAL Park Assist ON None None Warning Object Detected 78.7 in (200 cm) 3 Solid Yes, 1/2 second Warning Object Detected 39.3 in (100 cm) 3 Flashing Slow Tone Warning Object Detected 27.5 in (70 cm) 31.4 in (80 cm) 3 Flashing Slow Tone Warning Object Detected 25.5 in (65 cm) 25.5 in (65 cm) 2 Flashing Fast Tone Warning Object Detected 19.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. When the shift lever is moved to REVERSE and the system is disabled, the EVIC will display the “PARK ASSIST DISABLED” message for as long as the vehicle is in REVERSE.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When you turn ParkSense威 off, the instrument cluster • Clean the ParkSense威 sensors regularly, taking care will display “PARK ASSIST DISABLED.” Furthernot to scratch or damage them. The sensors must not more, once you turn ParkSense威 off, it remains off be covered with ice, snow, slush, mud, dirt, or debris. until you turn it on again, even if you cycle the ignition Failure to do so can result in the ParkSense威 system key. not working properly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 CAUTION! WARNING! • ParkSense威 is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the ParkSense威 sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using ParkSense威 to be able to stop in time when the obstacle is detected.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Before using the ParkSense威 Rear Park Assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns on the single flashing arc and sounds the continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! 187 CAUTION! (Continued) Drivers must be careful when backing up even when using the ParkView威 Rear Back Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning ParkView姞 On or Off — With Navigation/Multimedia Radio Turning ParkView姞 On or Off — Without Navigation/Multimedia Radio 1. Press the “menu” hard key. 1. Press the “menu” hard key. 2. Select ⬙system setup⬙ soft key. 2. Select “system setup” soft key. 3. Press the “camera setup” soft key. 3. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft key. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 OVERHEAD CONSOLES Front Overhead Console Two versions of the overhead console are available. The base front overhead console model featured fixed incandescent courtesy/reading lights, flip-down sunglass storage and conversation mirror.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle. Press a second time to turn each light off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 Rear Courtesy/Reading Lights — If Equipped The overhead console has two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed. Overhead Compartment Features 1 2 3 4 1 — DVD 1 — Rear HVAC — Interior Lights — Storage If equipped, otherwise storage.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Console Halo Lighting The rear overhead console has recessed halo lighting around the perimeter of the console base. This feature provides additional lighting options while traveling and is controlled by the headlight switch. Refer to “Lights/ Halo Lights — If Equipped” in “Understanding the Features Of Your Vehicle” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 Programming HomeLink姞 WARNING! • Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Place the handheld transmitter 1 to 3 in (3 to 8 cm) away • After training a HomeLink威 channel, if the garage from the HomeLink威 button you wish to program while door does not operate with HomeLink威 and the gakeeping the indicator light in view. rage door opener was manufactured after 1995, the garage door opener may have a rolling code. If so, 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 This can usually be found where the hanging antenna 6. Firmly press and release the LEARN or TRAINING wire is attached to the garage door opener motor. It is button. The name and color of the button may vary by NOT the button normally used to open and close the manufacturer. door. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 7.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink威 To operate, press and release the programmed HomeLink威 button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The handheld transmitter of the device may also be used at any time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 successfully accepted the frequency signal. The indica- Troubleshooting Tips tor light will flash slowly and then rapidly when fully If you are having trouble programming HomeLink威, here are some of the most common solutions: trained. If you unplugged the device for training, plug it back in • Replace the battery in the original transmitter. at this time. • Press the LEARN button on the Garage Door Opener to complete the training for a Rolling Code.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. This device must accept any interference that may be Power Sunroof Operation received including interference that may cause undesired Opening the Sunroof Manually operation. Press the switch rearward and hold, and the sunroof will open automatically from any position. The sunroof will NOTE: • The transmitter has been tested and it complies with open fully, then stop automatically. During this operaFCC and IC rules.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Closing the Sunroof Manually To close the sunroof from an open or vent position, press and hold the switch forward. The sunroof will close fully and stop automatically. Release the switch to stop sunroof travel at any point. 199 WARNING! Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Express Close Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully, then stop automatically. This is called “Express Close”. During Express Close operation, any movement of the sunroof switch will stop the sunroof. WARNING! Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object to project through the sunroof opening.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 with the sunroof open, adjust the sunroof opening to • Do not exceed the maximum power of 160 Watts (13 minimize the buffeting or open any window. Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will Sunroof Maintenance need to be replaced. Use only a non-abrasive cleaner and a soft cloth to clean the glass panel.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE One outlet in the removable floor console shares a fuse with the lower outlet in the instrument panel and is also connected to the battery. Do not exceed a maximum power of 160 Watts (13 Amps) shared between the lower panel outlet and the removable floor console outlet. The outlet in the rear quarter panel near the liftgate and the upper outlet in the instrument panel are both controlled by the ignition switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 CAUTION! CAUTION! (Continued) • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximately 170 Watts, the power inverter may have to be reset manually. To reset the inverter manually press the power inverter button OFF and ON.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 To turn on the power outlet, press the switch once. Press CUPHOLDERS There are nine cupholders in the interior. Two cupholders the switch a second time to turn the power outlet off. in the center front instrument panel, four in the floor consoles and three more are located in the third row quarter trim panel. All liners are removable for cleaning. Pull the flexible liner from the cupholder drawer or tray starting at one edge for easy removal.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE variety of container types and sizes. Press down on the Instrument Panel Cupholders The instrument panel cupholders are located in a pull-out container to engage the cupholder retention features. drawer just above the lower storage bin. Interior Bottle Holders There are four bottle holders located in the interior.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 of the two cupholders in the center front instrument panel. To install the ash receiver, align the receiver so the thumb grip on the lid is facing rearward. Press the ash receiver into either of the cup wells to secure. Pull upward on the ash receiver to remove for cleaning and/or storage. The left rear trim panel cupholder is designed to accommodate a second ash receiver, if desired.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To close the compartment door, push firmly downward Lower Glove Compartment on the door’s surface to release the detent and latch the To open the lower compartment, pull out on the release handle (3). The lower compartment handle is also door closed. equipped with a lock (3).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Door Trim Panel Storage WARNING! Front Door Storage Both interior front door panels have multiple pockets for storage. If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burning the occupants. Be careful when closing the doors to avoid injury.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver Seatback Storage — If Equipped Umbrella Holder The drivers seatback has a primary storage pocket on all An umbrella holder has been conveniently molded into models and an optional secondary mesh pocket. the left front door entry scuff molding.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second Row Floor Storage Bins The area below the floor covers, located in front of the second row seats, is available for storage. 211 CAUTION! The storage bin cover must lay flat and be locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. 3 WARNING! Storage Bin Cover Lock Release Pull up on the storage bin latch to open the cover.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage Bin Safety Warning Carefully follow these warnings to help prevent personal injury or damage to your vehicle: WARNING! • Always close the storage bin covers when your vehicle is unattended. • Do not allow children to have access to the second row seat storage bins. Once in the storage bin, young children may not be able to escape. If trapped in the storage bin, children can die from suffocation or heat stroke.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seat Storage Bin Cover Emergency Release Lever As a security measure, your vehicle may be built with a Storage Bin Cover Emergency Release is built into the storage bin cover latching mechanism. 213 NOTE: In the event of an individual being locked inside the storage bin, the storage bin cover can be opened from inside of the bin by pushing on the glow-in-the-dark lever attached to the storage bin cover latching mechanism.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle. Cargo Area Storage The liftgate sill plate has a raised line with the statement “Load To This Line”. This line indicates how far rearward cargo can be placed without interfering with liftgate closing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 Basic Console Basic Console features consist of the following: • The basic console profile allows vehicle occupants to easily pass through the first row to the second. • Four cupholders accept up to extra large size beverage cups or 20 oz (.6 L) plastic bottles. Cupholders are dishwasher safe for cleaning. • The cupholders are removable to access a large storage bin.
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Remove the console. WARNING! To Reinstall The Basic Floor Console 1. Position the console at a slight angle (front slightly higher than the rear). 2. Slide the console rearward into the floor bracket/ hook. In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched. Premium Console — If Equipped 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 • Large console center storage will store headphones for the available rear DVD entertainment system or other items • 12 Volt DC power outlet provides continuous power inside the console for cell phones or other electronics. 3 • Rear occupant accessible • Multiple adjustments • Removable from vehicle for additional floor space.
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE holder insert for both cavities can easily be removed for Position 2 shows the raised storage tray revealing a large cleaning. The cupholders will also accommodate large storage area below. size cups and 20 oz (.6 L) bottles. Position 1 shows the console closed with four cupholders and a convenient storage tray. Console Position 2 Console Position 1 Dual Storage Bins Position 3 shows the top portion of the console in a rearward position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 easy access to the storage area below and provides two of the four cupholders for the second row passengers. 3 Console Position 4 To Remove The Premium Floor Console Console Position 3 1. Pull up on the bottom release handle in the front of the Position 4 shows the complete console in its rearmost console. position. Again, lifting second latch handle at the front of the console, allows complete access to a lower storage bin 2.
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull rearward to disengage from floor and remove console. To reinstall the console: 1. Position the console at a slight angle (rear slightly higher than the front). WARNING! In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched. 2. Slide the console forward into the floor bracket. REAR WINDOW FEATURES 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • You can turn off the heated mirror feature at anytime by pressing the rear window defroster switch a second time. • To prevent excessive battery drain, use the rear window defroster only when the engine is operating. CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window.
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and side rails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To help control wind noise when installing the crossbars ensure the embossed arrow is facing the front of the vehicle. When the crossbars are not in use, the front crossbar should be fastened just forward of the middle support and the rear crossbar should be fastened at the rearmost position of the side rails. This will help reduce the amount of wind noise when the crossbars are not in use.
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack. SUN SCREENS — IF EQUIPPED Sun screens are available for second and third row seating windows.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 Gently pull up on the tab to raise the sun screen. Continue pulling the sun screen until the tab is near the top of the window. 3 Sun Screen Extended To lower the sun screen, gently lift the tab upward to disengage the hooks, and feed the screen back into the base sill. Sun Screen Attaching To Retainer Clips Once the screen is completely to the top of the window, extend the top bar of the sun screen over the two hooks attached to the top of the window.
I nf or mat i onPr ov i dedby :
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 231 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 232 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 233 䡵 Compass Mini-Trip Computer (CMTC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 247 ▫ CMTC Reset Buttons . . . . . . . . . . . . . . . . . . 247 ▫ Compass/Temperature Display . . . . . . . . . .
228 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions — Voice Command System (VR) — If Equipped . . . . . . . . . . . . . 263 ▫ Operating Instructions — Uconnect™ Phone — If Equipped . . . . . . . . . . . . . . . . . . . . . . 263 ▫ Clock Setting Procedure — RBZ Radio . . . . . 263 ▫ Clock Setting Procedure — RER Radio . . . . . 265 䡵 Media Center 130 (RES) — AM/FM Stereo Radio With CD Player (MP3 AUX Jack). . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 290 ▫ List Or Browse Mode . . . . . . . . . . . . . . . . . 292 䡵 Uconnect™ Multimedia (Satellite Radio) — If Equipped (REN/RER/RBZ/RES Radios Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 ▫ System Activation . . . . . . . . . . . . . . . . . . . . 294 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . .
230 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Three-Zone Temperature Control — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 307 ▫ Rear Manual Climate Control — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 309 ▫ Automatic Temperature Control (ATC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 312 ▫ Summer Operation . . . . . . . . . . . . . . . . . . . 320 ▫ Winter Operation . . . . . . . . . . . . . . . . . . . . 321 ▫ Vacation/Storage . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 231 INSTRUMENT PANEL FEATURES 4 1 — Air Vents 2 — Instrument Cluster 3 — Shift Lever 4 — Radio 5 — Analog Clock 6 — Upper Glove Compartment 7 — Lower Glove Compartment 8 — Climate Controls 9 — DVD – If Equipped 10 — Cup Holders 13 — Switch Bank 14 — Ignition Switch 11 — Storage Bin 15 — Dimmer Switch 12 — Power Supply – 12V 16 — Headlight Switch I nf or mat i onPr ov i dedby :
232 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER I nf or mat i onPr ov i dedby :
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 233 vehicle has completely stopped and the shift lever is placed in the PARK position, the light should turn off. 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when If the light remains lit with the engine running, your vehicle will usually be drivable; however, see an authothe ignition switch is in the ON position. rized dealer for service as soon as possible. If the light is 2.
234 UNDERSTANDING YOUR INSTRUMENT PANEL vehicle is experiencing a problem with the charging (TPMS) that illuminates a low tire pressure telltale when system. Obtain SERVICE IMMEDIATELY. See an autho- one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumirized dealer. nates, you should stop and check your tires as soon as If jump starting is required, refer to “Jump Starting possible, and inflate them to the proper pressure.
UNDERSTANDING YOUR INSTRUMENT PANEL system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended.
236 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Oil Pressure Warning Light This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 10. Electronic Stability Program (ESP) Indicator Light WARNING! / Brake Assist System (BAS) Warning Light The malfunction light for the Electronic Stabil- If a warning light remains on the system may not be ity Program (ESP) is combined with Brake working and you will not have the benefit of ESP or Assist System (BAS). The yellow “ESP/BAS BAS.
238 UNDERSTANDING YOUR INSTRUMENT PANEL If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Program (ESP) system. In this case, the light will remain on until the condition has been corrected.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 Operation of the Brake Warning Light can be checked by 13. Anti-Lock Brake (ABS) Light turning the ignition switch from the OFF position to the This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition ON position. The light should illuminate for approxiswitch is turned to the ON position and may mately two seconds. The light should then turn off unless stay on for as long as four seconds.
240 UNDERSTANDING YOUR INSTRUMENT PANEL 14. Electronic Stability Program (ESP) Indicator Light 17. Front Fog Light Indicator — If Equipped This indicator will illuminate when the front fog / Traction Control System (TCS) Indicator Light lights are on. If this indicator light flashes during acceleration, apply as little throttle as possible. While 18. Seat Belt Reminder Light driving, ease up on the accelerator.
UNDERSTANDING YOUR INSTRUMENT PANEL the ON position, before engine start. If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the MIL after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require towing.
242 UNDERSTANDING YOUR INSTRUMENT PANEL 21. Temperature Gauge The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 NOTE: On the Base cluster, the reset button toggles between odometer, Trip A, Trip B, ECO and outside temperature. To reset a message display on Base Cluster (gATE, gASCAP, noFUSE, CHangE OIL, LoCOOL, LoWASH, etc.), push and hold the button until the display resets (approximately two seconds). door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Ajar gATE . . . . . . . . . . . . . . . . . . . . . . . . . . . Liftgate Ajar LoW tirE. . . . . . . . . .
244 UNDERSTANDING YOUR INSTRUMENT PANEL ECO / ECO-on (Fuel Saver Indicator) — If Equipped The ECO-on indicator will illuminate when you are driving in a fuel efficient manner and can be used to modify driving habits in order to increase fuel economy. The ECO display will toggle between ECO and ECO-on depending on driving habits and vehicle usage.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 means the engine oil change interval may fluctuate 25. Odometer dependent upon your personal driving style. The odometer shows the total distance the vehicle has been driven. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN U.S. Federal regulations require that upon transfer of position.
246 UNDERSTANDING YOUR INSTRUMENT PANEL 26. Compass Mini-Trip Computer (CMTC) or Electronic 27. Compass Mini-Trip Computer (CMTC) Display Vehicle Information Center (EVIC) Display — If Button Press the left reset button to scroll through sub-menus Equipped (i.e., Outside Temperature, Trip Functions: AVG Fuel Compass Mini-Trip Computer (CMTC) Display — If Economy, DTE, Elapsed Time, and Units).
UNDERSTANDING YOUR INSTRUMENT PANEL 247 NOTE: The system will display the last known outside temperature when starting the vehicle and may need to be driven several minutes before the updated temperaNOTE: ture is displayed. Engine temperature can also affect the • The compass on your vehicle is self-calibrating, elimidisplayed temperature, therefore temperature readings nating the need to manually calibrate the compass. are not updated when the vehicle is not moving.
248 UNDERSTANDING YOUR INSTRUMENT PANEL When the appropriate conditions exist, the following cluster to switch from odometer, to Trip A or Trip B, or to messages will display: ECO. Press and hold the right button while the odometer/trip odometer is displayed to reset. NE . . . . . . . Eight-point compass headings are displayed Trip A (N, S, E, W, NE, NW, SE, SW) 14°F. . . . . . . . . . . . Temperature (Fahrenheit or Celsius) AVG . . . . . . . . . Average Fuel Economy (U.S. or Metric) DTE . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL Compass/Temperature Display Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To ensure compass accuracy, the compass variance should be properly set according to the variance map for the zone where the vehicle will be driven. When properly set, the compass will automatically account for this difference. 249 and such devices may interfere and cause false compass readings.
250 UNDERSTANDING YOUR INSTRUMENT PANEL To Set the Variance Start the engine and leave the transmission gear selector lever in the PARK position. Press and hold the CMTC reset button (for approximately ten seconds) until the current variance zone number is displayed. To change the zone, press and release the CMTC reset button to increase the variance one step. Repeat as necessary until the desired variance is achieved. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 • Vehicle information warning message displays • Tire Pressure Monitor System • Personal Settings (Customer-Programmable Features) • Compass display • Outside temperature display • Trip computer functions • Audio Modes display EVIC Menu / Step Control Button, as it appears on the left side of the steering wheel spoke.
252 UNDERSTANDING YOUR INSTRUMENT PANEL Press and release the MENU button, and the mode displayed will change between Compass/Temperature, Trip, System Status, and Personal Settings. Press this button to RESET Trip Functions and change Personal Settings. Electronic Vehicle Information Center (EVIC) Press the STEP button to scroll through sub Displays menus (i.e., Trip Functions, Avg. Fuel Economy, When the appropriate conditions exist, the EVIC displays DTE, Elapsed Time, and Units).
UNDERSTANDING YOUR INSTRUMENT PANEL • LOW WASHER FLUID • Oil Change Required • Check Gascap • Left Front Turn Signal Light Out • Left Rear Turn Signal Light Out • Right Front Turn Signal Light Out • Right Rear Turn Signal Light Out 253 • Blind Spot System Not Available — This message is displayed to indicate the Blind Spot Monitor (BSM) system is temporarily unavailable due to sensor blockage, electronic interference, or other ⬙temporary⬙ conditions.
254 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Change Required Your vehicle is equipped with an engine oil change indicator system. The Oil Change Required message will flash in the EVIC display for approximately 10 seconds, after a single chime has sounded, to indicate the next scheduled oil change interval. The engine oil change indicator system is duty-cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 “RESET” or show dashes for two seconds. Then, the significant amount of fuel to the vehicle will turn off the history information will be erased, and the averaging will ⬙LOW FUEL⬙ text and a new DTE value will display. continue from the last fuel average reading before the Elapsed Time reset. Shows the total elapsed time of travel since the last reset Distance To Empty (DTE) when the ignition switch is in the ACC position.
256 UNDERSTANDING YOUR INSTRUMENT PANEL Compass Display / ECO (Fuel Saver Mode) — If Equipped The compass readings indicate the direction the vehicle is facing. Press and release the compass button to display one of eight comCOMPASSpass readings, and the outside temperature. Button This feature allows you to monitor when you are driving in a fuel efficient manner, and it can be used to modify driving habits in order to increase fuel economy.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 2. Press the MENU button until Personal Settings NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Cell Phones, Lap(Customer-Programmable Features) menu is reached. 3. Press the STEP button until “Calibrate Compass” is tops and Radar Detectors. This is where the compass module is located, and it can cause interference with the displayed in the EVIC. compass sensor, and it may give false readings. 4.
258 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Press and hold the compass button for approximately Use the Step button to display one of the following choices. two seconds. 3. Press the STEP button until “Compass Variance” mes- Language sage, and the last variance zone number, displays in the When in this display you may select one of five languages for all display nomenclature, including the trip EVIC. functions and the navigation system (if equipped). Press 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 Auto UNLK On Exit When ON is selected, all doors will unlock when the vehicle is stopped and the transmission is in the PARK or NEUTRAL position and the driver’s door is opened. To make your selection, press and release the RESET button until ON or OFF appears. RKE Linked To Memory When this feature is selected the memory seat, mirror, and radio settings will return to the memory set position when the RKE transmitter UNLOCK button is pressed.
260 UNDERSTANDING YOUR INSTRUMENT PANEL Headlamp Off Delay When this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. To make your selection, press and release the RESET button until 0, 30, 60, or 90 appears. Tilt MIRR.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 unlocked with the RKE transmitter. To make your selec- NOTE: If your vehicle has experienced any damage in tion, press and release the RESET button until “OFF,” the area where the sensor is located, even if the fascia is not damaged, the sensor may have become misaligned. “30 sec.,” “60 sec.,” or “90 sec.” appears. Take your vehicle to an authorized dealer to verify sensor Blind Spot Alert alignment.
262 UNDERSTANDING YOUR INSTRUMENT PANEL Display Units of Measure In The EVIC, odometer, and navigation system (if equipped) can be changed between English and Metric units of measure. To make your selection, press and release the RESET button until ENGLISH or METRIC appears. Turn Headlights On with Remote Key Unlock When this feature is selected, the headlights will activate, and remain on for up to 90 seconds, when the doors are unlocked with the RKE transmitter.
UNDERSTANDING YOUR INSTRUMENT PANEL Rain Sensing Intermittent Wipers — If Equipped When ON is selected, the system will automatically activate the windshield wipers if it senses moisture on the windshield. To make your selection, press and release the RESET button until “ON” or “OFF” appears. When OFF is selected, the system reverts to the standard intermittent wiper operation.
264 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Touch the screen where the time is displayed, the clock Changing Daylight Savings Time When selected, this feature will display the time of day in setting menu will appear on the screen. daylight savings time. Proceed as follows to change the 3. To move the hour forward, touch the screen where the current setting: word “Hour” with the arrow pointing upward is displayed. To move the hour backward, touch the screen 1. Turn on the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 2. Touch the screen where the time is displayed. The want to select, touch the screen where the word “Page” is displayed to view additional time zones in the menu. clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in 5. Touch the screen where the word “Save” is displayed. the box next to the words “Show Time if Radio is Off.
266 UNDERSTANDING YOUR INSTRUMENT PANEL 4. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is displayed. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing downward is displayed. 2. Touch the screen where “User Clock” is displayed, the clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Daylight Savings.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 Touch the screen where the words “Show Time if Radio is MEDIA CENTER 130 (RES) — AM/FM STEREO Off” are displayed to change the current setting. RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Changing the Time Zone 1. Turn on the radio. 2. Touch the screen where the time is displayed. 4 3. Touch the screen where “User Clock” is displayed, the clock setting menu will appear on the screen. 4.
268 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next NOTE: The ignition switch must be in the ON or ACC listenable station in AM/FM mode. Press the right switch position to operate the radio. to seek up and the left switch to seek down. The radio Power Switch/Volume Control (Rotary) will remain tuned to the new station until you make Push the ON/VOLUME control knob to turn on the another selection. Holding either button will bypass radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 4. Adjust the minutes using the right side TUNE/ Push the rotary TUNE/SCROLL control knob a second SCROLL control knob. Press the TUNE/SCROLL control time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the knob to save time change. mid-range tones. 5. To exit, press any button/knob, or wait five seconds. Push the rotary TUNE/SCROLL control knob a third RW/FF time and TREBLE will display.
270 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob again to You may add a second station to each pushbutton by repeating the above procedure with this exception: Press exit setting tone, balance, and fade. the SET/RND button twice and SET 2 will show in the AM/FM Button display window. Each button can be set for SET 1 and Press the buttons to select either AM or FM mode. SET 2 in both AM and FM.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will NOTE: show the track number, and index time in minutes and • The ignition switch must be in the ON or ACC seconds. Play will begin at the start of track 1. position to operate the radio.
272 UNDERSTANDING YOUR INSTRUMENT PANEL EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD If you have ejected a disc and have not removed it within playing time display to a small CD playing time display. 10 seconds, it will be reloaded.
UNDERSTANDING YOUR INSTRUMENT PANEL 273 SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension.
274 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of characters in file/folder names: Supported MP3 File Formats The radio will recognize only files with the *.MP3 exten• Level 1: 12 (including a separator ⬙.⬙ and a threesion as MP3 files. Non-MP3 files named with the *.MP3 character extension) extension may cause playback problems. The radio is • Level 2: 31 (including a separator ⬙.⬙ and a three- designed to recognize the file as an invalid MP3 and will character extension) not play the file.
UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Bit Rate (kbps) Frequency (kHz) 320, 256, 224, 192, 160, 128, 48, 44.1, 32 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 24, 22.05, 16 56, 48, 40, 32, 24, 16, 8 275 Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium.
276 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device, such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. MEDIA CENTER 130 (RES/RSC) — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make NOTE: The ignition switch must be in the ON/RUN or another selection. Holding either button will bypass ACC position to operate the radio. stations without stopping until you release it.
278 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button Uconnect™ Phone — If Equipped Press this button to operate the Uconnect™ Phone feature (if equipped). Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details. 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 INFO Button Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text message broadcast from an FM station (FM mode only). Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones.
280 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade. MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display Soft Soft Rck Soft R&B Sports Talk Top 40 Weather 281 SETUP Button Pressing the SETUP button allows you to select between the following items: • Set Clock — Pressing the SELECT button will allow you to set the clock. Adjust the hours by turning the TUNE/SCROLL control knob. After adjusting the hours, press the TUNE/SCROLL control knob to set the minutes.
282 UNDERSTANDING YOUR INSTRUMENT PANEL window. Select the button (1–6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET/ RND button, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window.
UNDERSTANDING YOUR INSTRUMENT PANEL Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD player and the CD icon will illuminate on the radio display. If a CD does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and must be ejected before a new disc can be loaded. 283 CAUTION! (Continued) • Do not use adhesive labels. These labels can peel away and jam the player mechanism.
284 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Ejecting with the ignition OFF is not allowed on AM/FM Button Press the button to select either AM or FM mode. convertible or soft-top models (if equipped). SEEK Button Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection.
UNDERSTANDING YOUR INSTRUMENT PANEL Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. 285 a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.
286 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. MPEG Specification MPEG-1 Audio Layer 3 Sampling Bit Rate (kbps) Frequency (kHz) 320, 256, 224, 192, 160, 128, 48, 44.1, 32 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 24, 22.
UNDERSTANDING YOUR INSTRUMENT PANEL 287 Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob.
288 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an MP3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. TIME Button (Auxiliary Mode) Press this button to change the display to time of day.
UNDERSTANDING YOUR INSTRUMENT PANEL 289 NOTE: • If the radio has a USB port, connecting an iPod威 to this port does not play the media. For playing an iPod威, NOTE: This section is for sales code RES and REQ/ use the separate 16–pin connector port (in the glove REL/RET radios only with Uconnect™. For sales code compartment on some vehicles).
290 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • It may be necessary to remove the connector pin protection cap from the 16–pin connector port, prior to connecting the cable. Controlling The iPod姞 Using Radio Buttons To get into the UCI (iPod威) mode and access a connected iPod威, press the “AUX” button on the radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL jump to the previous track in the list. Turning this button at any other time in the track, will jump to the beginning of the current track. 291 beginning of the track. Pressing the SEEK >> button during play mode, it will jump to the next track in the list. • Jump backward in the current track by pressing and • While a track is playing, press the INFO button to see holding the << RW button. Holding the << RW the associated metadata (artist, track title, album, etc.
292 UNDERSTANDING YOUR INSTRUMENT PANEL • RND button (available on sales code RES radio only): Pressing this button toggles between Shuffle ON and Shuffle OFF modes for the iPod威. If the RND icon is showing on the radio display, then the shuffle mode is ON. List Or Browse Mode During Play mode, pressing any of the buttons described below, will bring up List mode. List mode enables scrolling through the list of menus and tracks on the iPod威. fast will scroll through the list faster.
UNDERSTANDING YOUR INSTRUMENT PANEL • Pressing a PRESET button will display the current list on the top line and the first item in that list on the second line. • To Exit List mode without selecting a track, press the same PRESET button again to go back to Play mode. • LIST button: The LIST button will display the top level menu of the iPod威. Turn the TUNE control knob to list the top-menu item to be selected and press the TUNE control knob.
294 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect™ Multimedia (SATELLITE RADIO) — IF EQUIPPED (REN/RER/RBZ/RES RADIOS ONLY) Satellite radio uses direct satellite-to-receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius Satellite Radio. This service offers over 130 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
UNDERSTANDING YOUR INSTRUMENT PANEL 295 Sirius ID number will display. The Sirius ID number bikes should be placed as far rearward as possible, within display will time out in two minutes. Press any button on the loading design of the rack. Do not place items directly on or above the antenna. the radio to exit this screen. ESN/SID Access With REN/RER/RBZ Radios Reception Quality While in SAT mode, press the MENU button on the radio Satellite reception may be interrupted due to one of the faceplate.
296 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button Pressing the INFO button will cycle the display information between Artist, Song Title, and Composer (if availNOTE: The ignition switch must be in the ON or ACC able). Also, pressing and holding the INFO button for an position to operate the radio. additional three seconds will make the radio display the SEEK Buttons Song Title all of the time (press and hold again to return Press and release the SEEK buttons to search for the next to normal display).
UNDERSTANDING YOUR INSTRUMENT PANEL 297 MUSIC TYPE Button • Display Sirius ID number — Press the AUDIO/ Pressing this button once will turn on the Music Type SELECT button to display the Sirius ID number. This mode for five seconds. Pressing the MUSIC TYPE button number is used to activate, deactivate, or change the or turning the TUNE/SCROLL control knob within five Sirius subscription. seconds will allow the program format type to be seSET Button – To Set the Pushbutton Memory lected.
298 UNDERSTANDING YOUR INSTRUMENT PANEL pushbutton memory. The channels stored in SET 2 service provider is SIRIUS Satellite Radio. SIRIUS Backmemory can be selected by pressing the pushbutton seat TV™ offers three video channels for family entertainment, directly from its satellites and broadcasting twice. studios. Every time a preset button is used, a corresponding NOTE: SIRIUS service is not available in Hawaii or button number will display. Canada and has limited coverage in Alaska.
UNDERSTANDING YOUR INSTRUMENT PANEL 299 • Additional single-disc DVD player with two-screen The LCD screen(s) are located in the overhead compartment console.
300 UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED VES™ Remote Control Location NOTE: Refer to the “Uconnect™ Multimedia” section of Uconnect™ User Manual located on the DVD for further details. Remote Sound System Controls (Back View Of Steering Wheel) The remote sound system controls are located on the rear surface of the steering wheel, at the three and nine o’clock positions.
UNDERSTANDING YOUR INSTRUMENT PANEL The right-hand rocker switch has a pushbutton in the center, and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume. Pressing the bottom of the rocker switch will decrease the volume. Pressing the center button changes the operation of the radio from AM to FM, or Tape to CD mode, depending on which radio is in the vehicle.
302 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particuCD/DVD DISC MAINTENANCE To keep a CD/DVD in good condition, take the following lar disc, it may be damaged (i.e., scratched, reflective precautions: coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known 1. Handle the disc by its edge; avoid touching the good disc before considering disc player service. surface. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 303 CLIMATE CONTROLS The Climate Control System allows you to regulate the temperature, amount, and direction of air circulating throughout the vehicle. The controls are located on the instrument panel, below the radio. Manual Heating and Air Conditioning System — If Equipped The controls for the manual system in this vehicle contain a series of outer rotary dials and inner push knobs. These comfort controls can be set to obtain desired interior conditions.
304 UNDERSTANDING YOUR INSTRUMENT PANEL Front Blower Control Temperature Control There are four blower speeds. Use this Use this control to regulate the temcontrol to regulate the amount of air perature of the air inside the passenger forced through the system in any compartment. Rotating the knob counmode you select. The blower speed terclockwise, from top center into the increases as you move the control blue area indicates cooler temperaclockwise from the off position. tures.
UNDERSTANDING YOUR INSTRUMENT PANEL Mode Control (Air Direction) Mode control allows you to choose from several selections of air distribution. You can select either a primary mode, as identified by the symbols, or a blend of two of these modes. The closer the control is to a particular mode, the more air distribution you receive from that mode. 305 Bi-Level Mode Air is directed through the panel and floor outlets.
306 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Defrost Mode Air is directed through the windshield and side • If the RECIRCULATION button is pressed when the window demist outlets. Use DEFROST mode with system is in MIX, DEFROST, or FLOOR mode the maximum blower and temperature settings for best RECIRCULATION LED indicator will flash 3 times to windshield and side window defrosting. indicate RECIRCULATION mode is not allowed.
UNDERSTANDING YOUR INSTRUMENT PANEL Economy Mode If ECONOMY mode is desired, press the A/C button to turn off the indicator light and the A/C compressor. Rotate the temperature control knob to the desired temperature. Air Conditioning Operation Push on this button to engage the Air Conditioning (A/C). A light will illuminate when the A/C System is engaged. 307 NOTE: The air conditioning compressor will not engage until the engine has been running for about 10 seconds.
308 UNDERSTANDING YOUR INSTRUMENT PANEL The Three-Zone Temperature Control bottom panel controls rear Heating, Ventilation, and Air Conditioning operations.
UNDERSTANDING YOUR INSTRUMENT PANEL 309 The primary control for the rear blower is on the front climate control unit located on the instrument panel. When the front control is in any position other than rear, the front control operates all the rear functions. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the “O” (Off) position.
310 UNDERSTANDING YOUR INSTRUMENT PANEL The rear blower and temperature controls for the rear Rear Blower Control seat passengers are located in the headliner, near the The primary control for the rear blower is on the front climate control unit, located on the instrument panel. center of the vehicle. Only when the front control for the rear blower is in the RR position do the second row seat occupants have control of the rear blower speed.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Interior air enters the Rear Manual Climate Control system through an intake grille, located in the right side trim panel behind the third row seats. The heater outlets are located in the right side trim panel, just behind the sliding door. Do not block or place objects directly in front of the inlet grille or heater outlets. The electrical system could overload, causing damage to the blower motor.
312 UNDERSTANDING YOUR INSTRUMENT PANEL Floor Mode Air comes from the floor outlets. Automatic Temperature Control (ATC) — If Equipped • The system can be controlled manually, if desired. • SYNC feature links the controls for all three zones, allowing one comfort setting (driver setting) for the cabin, if desired.
UNDERSTANDING YOUR INSTRUMENT PANEL 313 4 Front Upper ATC Panel 1 - System On/Off 2 - Blower Indicator 3 - Left Front Temperature 4 - Rear Blower / Temperature / Mode 5 - SYNC Indicator 6 - A/C Indicator 7 - Right Front Temperature 8 - Front MODE Indicator 9 - Air Conditioning (A/C) On/ Off 10 - AUTO Mode / Blower 11 - Front MODE 12 - RECIRCULATE Front Lower ATC Panel 1 - Rear Blower Speed 2 - Rear Temperature / Rear System On/Off 3 - Rear MODE 13 - Front DEFROST 14 - Front Blower Speed 15 - SYNC I nf
314 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • It is not necessary to move the temperature settings for 1. Press the AUTO button on the Front Upper ATC Panel cold or hot vehicles. The system automatically adjusts and the word AUTO will illuminate in the front ATC the temperature, mode and fan speed to provide display, along with three temperatures for driver, front comfort as quickly as possible. passenger, and rear seats.
UNDERSTANDING YOUR INSTRUMENT PANEL 315 Panel Mode Manual Operation Air is directed through the outlets in the instrument This system offers a full complement of manual override features. The AUTO symbol in the front ATC display will panel. These outlets can be adjusted for direction, be turned off when the system is being used in the and turned on or off to control airflow. manual mode.
316 UNDERSTANDING YOUR INSTRUMENT PANEL The SNOWFLAKE mode, or A/C button, allows Floor Mode Air comes from the floor outlets. A slight amount of the operator to manually activate or deactivate the air conditioning system. When in SNOWFLAKE air is directed through the defrost and side window mode, and the ATC display is on cool, dehumidified air demister outlets. flows through the air outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation Control When outside air contains smoke, odors, or high humidity, or if rapid cooling is desired, you may wish to recirculate interior air by pressing the RECIRCULATION mode control button. RECIRCULATION mode should only be used temporarily. The recirculation symbol will illuminate in the display when this button is selected. Push the button a second time to turn off the RECIRCULATION mode LED and allow outside air into the vehicle.
318 UNDERSTANDING YOUR INSTRUMENT PANEL The Rear ATC System is located in the headliner, near the 1. Press the REAR LOCK button on the front lower ATC center of the vehicle. panel. This turns off the REAR LOCK icon in the rear temperature knob. 2. Rotate the Rear Blower, Rear Temperature and the Rear Mode Control knobs to suit your comfort needs. 3. ATC is selected by adjusting the rear blower knob counterclockwise to AUTO.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode and fan speed to provide comfort as quickly as possible. • The temperature can be displayed in English or Metric units by selecting the “Display Units of Measure in” customer-programmable feature. Refer to the “Electronic Vehicle Information Center (EVIC) — CustomerProgrammable Features” in this Section.
320 UNDERSTANDING YOUR INSTRUMENT PANEL When rear controls are locked by the front system, the NOTE: In many temperature positions, the BI-LEVEL LOCK symbol on the temperature knob is illuminated mode is designed to provide cooler air out of the headliner outlets and warmer air from the floor outlets. and any rear overhead adjustments are ignored. Rear Mode Control Floor Mode Air comes from the floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Winter Operation To ensure the best possible heater and defroster performance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used. Refer to “Maintenance Procedures” in “Maintaining Your Vehicle” for proper coolant selection. Use of the air RECIRCULATION mode during Winter months is not recommended, because it may cause window fogging.
322 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips A/C Air Filter— If Equipped On vehicles equipped with Automatic Temperature Control (ATC), the climate control system filters out dust and pollen from the air. Refer to “Air Conditioning” in “Maintaining Your Vehicle” for filter replacement instructions.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 327 䡵 Automatic Transmission . . . . . . . . . . . . . . . . . 330 ▫ Automatic Transmission . . . . . . . . . . . . . . . 327 ▫ Key Ignition Park Interlock . . . . . . . . . . . . . 330 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 327 ▫ Brake/Transmission Interlock System . . . . . . 331 ▫ Extreme Cold Weather (Below ⫺20°F Or –29°C) . . . . . . . . . . . . . . .
324 STARTING AND OPERATING 䡵 Driving Through Water . . . . . . . . . . . . . . . . . 339 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . 352 ▫ Flowing/Rising Water . . . . . . . . . . . . . . . . . 339 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . 352 ▫ Shallow Standing Water . . . . . . . . . . . . . . . 339 ▫ Tire Identification Number (TIN) . . . . . . . . . 355 䡵 Power Steering . . . . . . . . . . . . . . . . . . . . . . . 341 ▫ Tire Terminology And Definitions . . .
STARTING AND OPERATING 325 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . 367 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . 381 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . 367 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . 381 䡵 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 368 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . 382 䡵 Tire Rotation Recommendations . . . . . . . . . . . 369 ▫ Carbon Monoxide Warnings . . . .
326 STARTING AND OPERATING ▫ Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 387 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 394 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 387 ▫ Common Towing Definitions . . . . . . . . . . . . 394 ▫ Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . 387 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . 407 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! Never leave unattended children alone in a vehicle. Leaving children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key fob in the ignition switch.
328 STARTING AND OPERATING Extreme Cold Weather (Below ⫺20°F or –29°C) Follow the same instructions in the “Normal Starting” procedure. To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your authorized dealer) is recommended. If The Engine Fails To Start WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle.
STARTING AND OPERATING CAUTION! To prevent damage to the starter, DO NOT crank the engine for more than 15–second intervals at one time. Wait 10 to 15 seconds before trying again. 329 After Starting The idle speed will automatically decrease as the engine warms up. ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms the engine, and permits If the engine has been flooded, it may start to run, but not quicker starts in cold weather.
330 STARTING AND OPERATING AUTOMATIC TRANSMISSION WARNING! CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Move the shift lever into PARK only after the vehicle has come to a complete stop. • Do not move the shift lever from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Before moving the shift lever into any gear, make sure your foot is firmly on the brake pedal.
STARTING AND OPERATING Brake/Transmission Interlock System This vehicle is equipped with a Brake Transmission Shift Interlock System (BTSI) that holds the shift lever in the PARK position when the ignition switch is in the LOCK position. To move the shift lever out of the PARK position, the ignition switch must be turned to any other switch position (ACC, ON, or START) (engine running or not) and the brake pedal must be pressed.
332 STARTING AND OPERATING The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilometers). The transmission has only PRND shift positions.
STARTING AND OPERATING When parking on a hill, it is important to set the parking brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK. As an added precaution, turn the front wheels toward the curb on a downhill grade, and away from the curb on an uphill grade. WARNING! • Never use the PARK position as a substitute for the parking brake.
334 STARTING AND OPERATING WARNING! (Continued) • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key fob in the ignition switch. A child could operate power windows, other controls, or move the vehicle.
STARTING AND OPERATING NEUTRAL This range is used when vehicle is standing for prolonged periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have an accident.
336 STARTING AND OPERATING CAUTION! If the transmission operating temperature exceeds acceptable limits, the vehicle computer will override DRIVE and select “5” range (on six-speed transmissions) or “3” range (on four-speed transmissions) by changing shift points. This is done to prevent transmission damage due to overheating.
STARTING AND OPERATING Odometer Screen Display Actual Gear(s) Allowed (SixSpeed Transmission) Actual Gear(s) Allowed (Four-Speed Transmission) 1 2 3 4 5 6 D 1 1-2 1-3 1-4 1-5 1-6 1-6 1 1-2 1-3 1-4 N/A N/A 1–4 337 damage, the transmission automatically shifts into second gear (third gear for six-speed). The transmission remains in second gear (third gear for six-speed) despite the forward gear selected. PARK, REVERSE, and NEUTRAL will continue to operate.
338 STARTING AND OPERATING NOTE: Even if the transmission can be reset, it is recommended that you visit an authorized dealer at your earliest possible convenience. If the transmission cannot be reset, authorized dealer service is required. DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the front wheels to pull erratically to the right or left.
STARTING AND OPERATING 339 2. Slow down if the road has standing water or puddles. Flowing/Rising Water 3. Replace the tires when tread wear indicators first become visible. 4. Keep the tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off).
340 STARTING AND OPERATING CAUTION! CAUTION! (Continued) • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water. • Do not exceed 5 mph (8 km/h) when driving through standing water. This will minimize wave effects.
STARTING AND OPERATING WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
342 STARTING AND OPERATING • Upon initial start-up in cold weather, the power steering pump may make noise for a short amount of time. This is due to the cold, thick fluid in the steering system. This noise should be considered normal, and it does not in any way damage the steering system. WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible.
STARTING AND OPERATING WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturer’s recommended power steering fluid. 343 The foot operated parking brake is positioned below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully.
344 STARTING AND OPERATING When the parking brake is applied with the ignition difficult to move the shift lever out of PARK. The parking switch in the ON position, the “Brake Warning Light” in brake should always be applied whenever the driver is not in the vehicle. the instrument cluster will illuminate. NOTE: • When the parking brake is applied and the automatic transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver.
STARTING AND OPERATING WARNING! (Continued) • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also be certain to leave the transmission in PARK. Failure to do so may allow the vehicle to roll and cause damage or injury. CAUTION! If the Brake System Warning Light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately.
346 STARTING AND OPERATING WARNING! WARNING! (Continued) • The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed, or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals. • Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident.
STARTING AND OPERATING Anti-Lock Brake Warning Light The “Anti-Lock Brake Warning Light” monitors the anti-lock brake system. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. 347 If both the “Brake Warning Light” and the “Anti-Lock Brake Warning Light” remain on, the ABS and Electronic Brake Force Distribution (EBD) systems are not functioning. Immediate repair to the ABS system is required.
348 STARTING AND OPERATING wheel(s) and engine power is reduced, to provide enhanced acceleration and stability. A feature of the TCS functions similarly to a limited-slip differential, and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning.
STARTING AND OPERATING Brake Assist System (BAS) The Brake Assist System (BAS) is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes. This can help reduce braking distances. The BAS complements the ABS. Applying the brakes very quickly results in the best BAS assistance.
350 STARTING AND OPERATING Electronic Stability Program (ESP) The Electronic Stability Program (ESP) enhances directional control and stability of the vehicle under various driving conditions. ESP corrects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the over/under steer condition. Engine power may also be reduced to help the vehicle maintain the desired path.
STARTING AND OPERATING 351 position, then goes out. If the “ESP/BAS Warning Light” comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system.
352 STARTING AND OPERATING NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. TIRE SAFETY INFORMATION Tire Markings • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
STARTING AND OPERATING 353 Tires designed to this standard have the letter “T” • High flotation tire sizing is based on U.S. design molded into the sidewall preceding the size designastandards and it begins with the tire diameter molded tion. Example: T145/80D18 103M. into the sidewall. Example: 31x10.5 R15 LT. Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....
354 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. 355 Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
356 STARTING AND OPERATING Tire Terminology and Definitions Term B-Pillar Cold Tire Pressure Maximum Inflation Pressure Recommended Inflation Pressure Tire Placard Definition The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.
STARTING AND OPERATING 357 Tire and Loading Information Placard Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar.
358 STARTING AND OPERATING To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard. Loading The combined weight of occupants, cargo/luggage and The vehicle maximum load on the tire must not exceed trailer tongue weight (if applicable) should never exceed the load carrying capacity of the tire on your vehicle. You the weight referenced here.
STARTING AND OPERATING 359 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if “XXX” • The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities amount equals 1,400 lbs (635 kg) and there will be five of your vehicle with varying seating configurations 150 lb (68 kg) passengers in your vehicle, the amount of and number and size of occupants.
360 STARTING AND OPERATING I nf or mat i onPr ov i dedby :
STARTING AND OPERATING 361 Safety WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure.
362 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Tire Inflation Pressures The proper cold tire inflation pressure is listed on the driver’s side “B” Pillar. The tire pressure should be checked and adjusted, and the tires inspected for signs of wear or visible damage, at least once a month.
STARTING AND OPERATING Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three-hour period. The cold tire inflation pressure must not exceed the maximum inflation pressure molded into the tire sidewall.
364 STARTING AND OPERATING WARNING! High-speed driving, with your vehicle at or above maximum load, is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial-Ply Tires Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING WARNING! (Continued) 365 CAUTION! • Temporary-use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. • Be sure to follow the warnings that apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control. Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed.
366 STARTING AND OPERATING WARNING! • Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. • Do not spin your vehicle’s wheels faster than 30 mph (48 km/h), or for more than 30 seconds continuously, when you are stuck; and do not let anyone near a spinning wheel, no matter what the speed.
STARTING AND OPERATING 367 Life of Tire Replacement Tires The service life of a tire is dependent upon varying The tires on your new vehicle provide a balance of many factors, including, but not limited to: characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manu• Driving style facturer strongly recommends that you use tires equiva• Tire pressure lent to the originals in size, quality and performance when replacement is needed.
368 STARTING AND OPERATING WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING 369 These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on All-Season type tires. Rotation will increase tread life, help to maintain mud, snow, and wet traction levels, and contribute to a Snow tires generally have lower speed ratings than what smooth, quiet ride.
370 STARTING AND OPERATING The suggested rotation method is shown in the following found on the tire placard located on the driver’s-side B-pillar. diagram. Tire Rotation The tire pressure will vary with temperature by about 1 psi (6.9 kPa) for every 12°F (6.5°C). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure.
STARTING AND OPERATING The TPMS will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above recommended cold tire placard pressure. Once the low tire pressure warning has been illuminated, the tire pressure must be increased to the recommended cold tire placard pressure in order for the “TPMS Warning Lamp” to be turned off.
372 STARTING AND OPERATING CAUTION! (Continued) • After inspecting or adjusting the tire pressure always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the TPMS sensor. • The TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, using an accurate tire pressure gage, even if under-inflation has not reached the level to trigger illumination of the “TPMS Warning Lamp.
STARTING AND OPERATING The Basic TPMS consists of the following components: • Receiver Module • Four Tire Pressure Monitoring Sensors 373 NOTE: The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) to receive this information. The “TPMS Warning Lamp” will flash on and off for 75 seconds, and remain on solid when a system fault is detected. The system fault will also sound a chime.
374 STARTING AND OPERATING 3. Accumulation of excessive snow and/or ice around 4. For each subsequent ignition switch cycle, a chime will the wheels or wheel housings. sound, the “TPMS Telltale Warning Light” will flash on and off for 75 seconds and then remain on solid. 4. Using tire chains on the vehicle. 5. Once you repair or replace the original road tire and 5. Using wheels/tires not equipped with TPMS sensors.
STARTING AND OPERATING 375 NOTE: It is particularly important to regularly check pressures are low. In addition, the EVIC will display a Low Pressure message for three seconds and a graphic and maintain proper tire pressure in all the tires. display of the pressure value(s) with the low tire(s) The Premium TPMS consists of the following compoflashing.
376 STARTING AND OPERATING Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is flashing on the graphic display to the vehicle’s recommended cold tire pressure value. The system will automatically update, the graphic display of the pressure value(s) will stop flashing, and the “TPMS Telltale Warning Light” will extinguish once the updated tire pressure(s) have been received.
STARTING AND OPERATING 377 will not be present, and a pressure value will be dis- 2. If you install the compact spare tire in place of a road played instead of dashes. A system fault can occur by any tire that has a pressure below the low-pressure warning of the following scenarios: limit, upon the next ignition switch cycle, the “TPMS Telltale Warning Light” will remain on, a chime will 1.
378 STARTING AND OPERATING 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically. In addition, the “TPMS Telltale Warning Light” will turn off and the graphic in the EVIC will display a new pressure value instead of dashes (- -), as long no tire pressure is below the low pressure warning limit in any of the four active road tires.
STARTING AND OPERATING 4.0L Engine The 4.0L engine is designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high-quality unleaded gasoline having an octane range of 87 to 89. The manufacturer recommends the use of 89 octane for optimum performance. The use of premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in these engines.
380 STARTING AND OPERATING Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE, and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle. CAUTION! E85 Usage In Non-Flex Fuel Vehicles Non-FFV vehicles are compatible with gasoline containing 10% ethanol (E10).
STARTING AND OPERATING 381 • disconnect and reconnect the battery to reset the It is even more important to look for gasoline without MMT in Canada, because MMT can be used at levels engine controller memory higher than those allowed in the United States. More extensive repairs will be required for prolonged MMT is prohibited in Federal and California reformuexposure to E85 fuel. lated gasoline.
382 STARTING AND OPERATING Fuel System Cautions CAUTION! (Continued) CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance and damage the emission control system. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat.
STARTING AND OPERATING Carbon Monoxide Warnings 383 WARNING! (Continued) WARNING! Carbon monoxide (CO) in exhaust gases is deadly. • To prevent carbon monoxide poisoning DO NOT inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. • NEVER run the engine in a closed area, such as a garage, and NEVER sit in a parked vehicle with the engine running for an extended period.
384 STARTING AND OPERATING the other sections of this manual for information on features that are common between Flexible Fuel and gasoline only powered vehicles. CAUTION! Only vehicles with the E85 fuel filler door label can operate on E85.
STARTING AND OPERATING 385 Ethanol Fuel (E85) For best results, a refueling pattern that avoids alternatE85 is a mixture of approximately 85% fuel ethanol and ing between E85 and unleaded gasoline is recom15% unleaded gasoline. mended. When you do switch fuel types, it is recommended that: WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank.
386 STARTING AND OPERATING • Some additives used in regular gasoline are not fully compatible with E85 and may form deposits in your engine. To eliminate driveability issues that may be caused by these deposits, a supplemental gasoline additive, such as MOPAR威 Injector Cleanup or Techron may be used. Selection Of Engine Oil For Flexible Fuel Vehicles E85 and Gasoline Vehicles FFV vehicles operated on E85 require specially formulated engine oils.
STARTING AND OPERATING Replacement Parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol compatible parts. 387 ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door on the left side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
388 STARTING AND OPERATING NOTE: The driver’s side sliding door cannot be opened while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the fuel door. CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap).
STARTING AND OPERATING 389 • If the gas cap is not tightened properly, the MIL may If the problem continues, the message will appear the come on. Be sure the gas cap is tightened every time next time the vehicle is started. See your authorized dealer as soon as possible. the vehicle is refueled.
390 STARTING AND OPERATING • Gross Axle Weight Rating (GAWR) — Front Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR.
STARTING AND OPERATING 391 Rim Size Overloading This is the rim size that is appropriate for the tire size The load carrying components (axle, springs, tires, listed. wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and front Inflation Pressure and rear GAWR. This is the cold tire inflation pressure for your vehicle, for all loading conditions up to full GAWR.
392 STARTING AND OPERATING Loading CAUTION! To load your vehicle properly, first figure out its empty weight, axle-by-axle and side-by-side. Store heavier items Do not load your vehicle any heavier than the GVWR down low and be sure you distribute their weight as or the maximum front and rear GAWR. If you do, evenly as possible. Stow all loose items securely before parts on your vehicle can break, or it can change the driving. If weighing the loaded vehicle shows that you way your vehicle handles.
STARTING AND OPERATING 393 LOADING TABLE — EXAMPLE ONLY Front Axle Rear Axle TOTAL 2,500 lbs 2,450 lbs (1 134 kg) (1 111 kg) GAWR 2,544 lbs 2,544 lbs (1 154 kg) (1 154 kg) A loaded vehicle is shown in the above table. Note that neither the GVWR nor the GAWR capacities have been exceeded.
394 STARTING AND OPERATING TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. that you do not exceed the GVWR. Refer to “Vehicle Loading/Vehicle Certification Label” in “Starting and Operating” for further information.
STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. Refer to “Vehicle Loading/Vehicle Certification Label” in “Starting and Operating” for further information. WARNING! 395 Frontal Area The frontal area is the maximum height multiplied by the maximum width of the front of a trailer.
396 STARTING AND OPERATING Weight-Distributing Hitch A weight-distributing system works by applying leverage through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer’s axle(s). When used in accordance with the manufacturer’s directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.
STARTING AND OPERATING 397 5 Without Weight-Distributing Hitch (Incorrect) With Weight-Distributing Hitch (Correct) I nf or mat i onPr ov i dedby :
398 STARTING AND OPERATING The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow, and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. TRAILER HITCH CLASSIFICATIONS Max. GTW (Gross Trailer Class Wt.
STARTING AND OPERATING 399 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission 3.3L, 3.8L and 4.0L/ Automatic GCWR (Gross Combined Wt. Rating) Frontal Area 7,000 lbs (3 175 kg) 22 sq ft (2.0 sq m) 7,000 lbs (3 175 kg) 22 sq ft (2.0 sq m) 7,000 lbs (3 175 kg) 22 sq ft (2.0 sq m) I nf or mat i onPr ov i dedby : Max. GTW (Gross Trailer Wt.
400 STARTING AND OPERATING Max. GTW (Gross Max. Tongue Wt. Trailer Wt.) Up to 2 persons & 9,000 lbs (4 082 kg) 40 sq ft (3.72 sq m) Luggage 3,800 lbs 380 lbs (172 kg) (1 723 kg)* 3.8L and 4.0L/ 3 to 5 persons & Automatic (with 9,000 lbs (4 082 kg) 40 sq ft (3.72 sq m) Luggage 3,350 lbs 335 lbs (152 kg) Tow Package) (1 519 kg)* 6 to 7 persons & 9,000 lbs (4 082 kg) 40 sq ft (3.
STARTING AND OPERATING 401 Trailer and Trailer Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side-to-side, which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
402 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the “Tire Safety Information/Tire and Loading Information Placard” in “Starting and Operating” for the maximum combined weight of occupants and cargo for your vehicle.
STARTING AND OPERATING WARNING! 403 WARNING! (Continued) Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident.
404 STARTING AND OPERATING WARNING! (Continued) 3. GAWR 4. Trailer tongue weight rating for that trailer hitch. (This requirement may limit the ability to always achieve the 10% to 15% range of trailer tongue weight as a percentage of total trailer weight.) Towing Requirements – Tires • Check for signs of tire wear or visible tire damage before towing a trailer. Refer to “Tires – General Information” in “Starting and Operating” for the proper inspection procedure.
STARTING AND OPERATING • An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. • Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg).
406 STARTING AND OPERATING The Trailer Tow Package may include a four-pin or a seven-pin wiring harness. Use a factory approved trailer harness and connector. NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following four-pin connector and seven-pin connector illustrations.
STARTING AND OPERATING 407 Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Automatic Transmission The DRIVE gear can be selected when towing. However, if frequent shifting occurs while in DRIVE, move the shift lever into third gear (with four-speed transmission) or fifth gear (with six-speed transmission).
408 STARTING AND OPERATING The automatic transmission fluid and filter should be • Use speed control in flat terrain and with light loads to changed if you REGULARLY tow a trailer for more than maximize fuel efficiency. 45 minutes of continuous operation. Refer to “MainteCooling System nance Schedule” for the proper maintenance intervals.
STARTING AND OPERATING 409 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) CAUTION! Towing this vehicle behind another vehicle (flattowing with all four wheels on the ground) is not recommended. NOTE: If the vehicle requires towing, make sure all four wheels are off the ground.
I nf or mat i onPr ov i dedby :
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . 412 ▫ Secure The Spare Tire . . . . . . . . . . . . . . . . . 424 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 412 䡵 Jump-Starting Procedure . . . . . . . . . . . . . . . . 426 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 413 ▫ Preparations For Jump-Start . . . . . . . . . . . . . 427 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . 414 ▫ Jump-Starting Procedure . . . . .
412 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning flasher switch is located in the center of the instrument panel above the radio. IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional • On the highways — slow down.
WHAT TO DO IN EMERGENCIES 413 JACKING AND TIRE CHANGING CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, turn the engine off immediately, and call for service. WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.
414 WHAT TO DO IN EMERGENCIES Jack Location The jack, jack handle and winch handle tools are stowed behind the rear left side trim panel in the rear cargo area. Turn the two cover latches to release the cover. Spare Tire Removal The spare tire is stowed inside a protective cover located under the center of the vehicle between the front doors by means of a cable winch mechanism. The “spare tire drive” nut is located on the floor, under a plastic cap at the front of the floor console.
WHAT TO DO IN EMERGENCIES NOTE: The base console, if equipped, must be removed to raise and lower the spare tire. Refer to “Console Features” in “Understanding the Features of Your Vehicle” for console removal procedure. 415 WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.
416 WHAT TO DO IN EMERGENCIES NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked. Jacking Instructions WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised.
WHAT TO DO IN EMERGENCIES 417 Jack Warning Label 1. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 2. To remove the compact spare tire/cover assembly, assemble the winch handle extensions to form a “T” and fit the winch “T” handle over the drive nut, refer to “2” configuration in tool graphics. Rotate the nut to the left until the winch mechanism stops turning freely.
418 WHAT TO DO IN EMERGENCIES CAUTION! The winch mechanism is designed for use with the winch “T” handle only. Use of an air wrench or other power tools is not recommended and can damage the winch. 3. Assemble the winch handle extensions to form the Spare Tire Hook and pull the compact spare tire/cover assembly from under the vehicle, refer to “1” configuration in tool graphics.
WHAT TO DO IN EMERGENCIES 419 WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. NOTE: If either front tire is flat, it may be necessary to jack up the vehicle to remove the compact spare tire/ cover assembly from under the vehicle.
420 WHAT TO DO IN EMERGENCIES 4. When the compact spare tire/cover assembly is clear 5. There are two jack engagement locations on each side of the vehicle, stand the tire/cover assembly upright and of the vehicle body. These locations are on the sill flange remove the wheel spacer by squeezing the two retainer of the vehicle body. tabs together. NOTE: • Rear jack locations are between a pair of down-facing tabs on the sill flange of the vehicle side body.
WHAT TO DO IN EMERGENCIES 421 6 Jack Location I nf or mat i onPr ov i dedby :
422 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Do not attempt to raise the vehicle by jacking on locations other than those indicated in Step 5. Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Place the wrench on the jack screw and turn to the right until the jack head is properly engaged in the described location. Do not raise the vehicle until you are 8.
WHAT TO DO IN EMERGENCIES 423 10. Lower the vehicle by turning the jack screw to the 13. Place the deflated (flat) tire and compact spare tire left. cover assembly. in the rear cargo area. Do not stow the deflated tire in the spare tire location. Have the full11. Finish tightening the lug nuts. Push down on the sized tire repaired or replaced, as soon as possible. wrench while tightening for increased leverage. Alternate lug nuts until each nut has been tightened twice. The 14.
424 WHAT TO DO IN EMERGENCIES of operation, and after each time a tire is changed, to allow the wheel nuts to become properly set. All nuts should first be firmly seated against the wheel. The nuts should then be tightened to recommended torque. Tighten the nuts to final torque in increments. Progress around the bolt circle, tightening the nut opposite to the nut just previously tightened until final torque is achieved. Recommended torque is 95 ft lbs (130 N·m).
WHAT TO DO IN EMERGENCIES 2. Assemble the winch handle extensions to form the spare tire hook, and pull the wheel spacer from under the vehicle. 3. Turn the compact spare tire so that the valve stem is down, and place the tire into the spare tire/cover assembly. Slide the wheel spacer through the center of the wheel and spare tire/cover assembly, so that the two retainer tabs snap out and engage the spare tire cover on the opposite side.
426 WHAT TO DO IN EMERGENCIES CAUTION! CAUTION! The winch mechanism is designed specifically to stow a compact spare tire only. Do not attempt to use the winch to stow the full size flat tire, or any other full-size tire. Vehicle damage may result. Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.
WHAT TO DO IN EMERGENCIES Preparations for Jump-Start The battery in your vehicle is located on the left side of the engine compartment. Positive Battery Post 427 WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured.
428 WHAT TO DO IN EMERGENCIES 3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. WARNING! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. CAUTION! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1.
WHAT TO DO IN EMERGENCIES 429 8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. WARNING! Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery.
430 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then move the shift lever back and forth between REVERSE and DRIVE. Using minimal accelerator pedal pressure to maintain the rocking motion, without spinning the wheels, is most effective.
WHAT TO DO IN EMERGENCIES 431 • The towing speed must not exceed 30 mph (50 km/h). WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed.
432 WHAT TO DO IN EMERGENCIES CAUTION! (Continued) • Always use wheel lift equipment when towing from the front. The only other approved method of towing is with a flatbed truck. • Do not tow the vehicle from the rear. Damage to the rear sheet metal, liftgate and fascia will occur. • Do not push or tow this vehicle with another vehicle as damage to the bumper fascia and transmission may result.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 3.3/3.8L . . . . . . . . . . 435 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 441 䡵 Engine Compartment — 4.0L . . . . . . . . . . . . . 436 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 444 䡵 Onboard Diagnostic System — OBD II . . . . . . 437 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . 444 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 437 ▫ Exhaust System . . . . . . . . . . . . . . . . .
434 MAINTAINING YOUR VEHICLE ▫ Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458 ▫ Front Park/Turn Signal Lamp . . . . . . . . . . . 481 ▫ Automatic Transmission . . . . . . . . . . . . . . . 461 ▫ Front Side Marker Lamp . . . . . . . . . . . . . . . 482 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . 464 ▫ Fog Lamp . . . . . . . . . . . . . . . . . . . . . . . . . 482 ▫ Cleaning The Instrument Panel Cupholders . . 469 䡵 Fuses . .
MAINTAINING YOUR VEHICLE 435 ENGINE COMPARTMENT — 3.3/3.8L 7 1 2 3 4 5 6 — Air Cleaner Filter — Automatic Transmission Dipstick (3.
436 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 4.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
438 MAINTAINING YOUR VEHICLE For states that require an Inspection and Mainte“Electronic Vehicle Information Center (EVIC)” in ”Unnance (I/M), this check verifies the “Malfunction derstanding Your Instrument Panel” for further informaIndicator Light (MIL)” is functioning and is not tion. Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tight- on when the engine is running, and that the OBD II system is ready for testing. ened.
MAINTAINING YOUR VEHICLE 439 2. If you crank or start the engine, you will have to start If your OBD II system is not ready, you should see your this test over. authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, 3.
440 MAINTAINING YOUR VEHICLE REPLACEMENT PARTS Use of genuine MOPAR威 parts for normal/scheduled maintenance and repairs is highly recommended to ensure the designed performance. Damage or failures caused by the use of non-MOPAR威 parts for maintenance and repairs will not be covered by the manufacturer’s warranty. DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.
MAINTAINING YOUR VEHICLE 441 Engine Oil CAUTION! • Failure to properly maintain your vehicle or perform repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle performance. Immediately have potential malfunctions examined by an authorized Chrysler Group LLC dealership or qualified repair center.
442 MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has Overfilling or underfilling will cause oil aeration, or been certified by the American loss of oil pressure. This could damage your engine. Petroleum Institute (API). The manufacturer only recommends Change Engine Oil API Certified engine oils. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.
MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) – 3.3L & 3.8L Gasoline Engines SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Your engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. 443 For information on engine oil filler cap location, refer to “Engine Compartment” in “Maintaining Your Vehicle” for further information.
444 MAINTAINING YOUR VEHICLE Disposing of Used Engine Oil and Oil Filters Engine Air Cleaner Filter Care should be taken in disposing of used engine oil and Refer to “Maintenance Schedule” for the proper mainteoil filters from your vehicle. Used oil and oil filters, nance intervals. indiscriminately discarded, can present a problem to the WARNING! environment. Contact your authorized dealer, service station, or governmental agency for advice on how and The air induction system (air cleaner, hoses, etc.
MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have an authorized technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
446 MAINTAINING YOUR VEHICLE CAUTION! • The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter damage: • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idle or malfunctioning operating conditions.
448 MAINTAINING YOUR VEHICLE CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Warranty Information Book, located on the DVD, for further warranty information. • The air conditioning system contains refrigerant under high pressure.
450 MAINTAINING YOUR VEHICLE WARNING! Do not remove the A/C air filter while the blower is operating or personal injury may result. The A/C air filter is located in the fresh air inlet behind the glove box. Perform the following procedure to replace the filter: 1. Open the glove compartment and remove all contents. 2. Push in on the sides of the glove compartment and lower the door. A/C Air Filter Replacement 3. Pivot the glove compartment downward. 5.
MAINTAINING YOUR VEHICLE CAUTION! The A/C air filter is labeled with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 451 hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring.
452 MAINTAINING YOUR VEHICLE Avoid using the wiper blades to remove frost or ice from The washer fluid reservoir will hold a full gallon of fluid the windshield. Keep the blade rubber out of contact with when the Low Washer Fluid Light illuminates. petroleum products such as engine oil, gasoline, etc. WARNING! NOTE: Life expectancy of wiper blades varies depending on geographical area and frequency of use.
MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at anytime the ignition switch is in the ON position. • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.
454 MAINTAINING YOUR VEHICLE Cooling System – Drain, Flush and Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze) solution. Refer to “Maintenance Schedule” for the proper maintenance intervals.
MAINTAINING YOUR VEHICLE CAUTION! (Continued) • This vehicle has not been designed for use with Propylene Glycol-based engine coolant (antifreeze). Use of Propylene Glycol-based engine coolant (antifreeze) is not recommended. 455 • The manufacturer recommends using MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. • Mix a minimum solution of 50% HOAT engine coolant and distilled water.
456 MAINTAINING YOUR VEHICLE NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent coolant changes. Cooling System Pressure Cap The cap must be fully tightened to prevent the loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle.
MAINTAINING YOUR VEHICLE Disposal of Used Coolant Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol-based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately.
458 MAINTAINING YOUR VEHICLE If an examination of your engine compartment shows no • Make sure that the radiator and coolant recovery evidence of radiator or hose leaks, the vehicle may be bottle overflow hoses are not kinked or obstructed. safely driven. The vapor will soon dissipate. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, also keep the front of • Do not overfill the coolant recovery bottle. the condenser clean.
MAINTAINING YOUR VEHICLE WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency. 459 Clean the top of the master cylinder area before removing the cap. Add fluid to bring the level up to the top of the “FULL” mark on the side of the master cylinder reservoir.
460 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid for your vehicle is also labeled on the original factory installed hydraulic master cylinder reservoir.
MAINTAINING YOUR VEHICLE WARNING! (Continued) • Do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in an accident. Automatic Transmission The automatic transmission and differential assembly are contained within a single housing. The fluid level in the automatic transmission should be checked whenever the vehicle is serviced.
462 MAINTAINING YOUR VEHICLE 2. The engine should be running at curb idle speed for a minimum of 60 seconds. CAUTION! Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter changes.
MAINTAINING YOUR VEHICLE 463 a. If the fluid is hot, the reading should be in the Fluid Level Check (3.8L and 4.0L Engines with crosshatched area marked “HOT” (between the upper Six-Speed Automatic Transmission) – If Equipped The six-speed automatic transmission is a sealed unit and two holes in the dipstick). has no dipstick. See your authorized dealer to have the b. If the fluid is cold, the fluid level should be between transmission fluid checked or serviced.
464 MAINTAINING YOUR VEHICLE CAUTION! Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.
MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR威 Car Wash or equivalent, or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumulated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover or equivalent to remove. 465 CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces.
466 MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. heavy soil and/or excessive brake dust, use MOPAR威 Wheel Cleaner or equivalent or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Only MOPAR威 or equivalent is recommended.
MAINTAINING YOUR VEHICLE 467 • For tough stains, apply MOPAR威 Total Clean or equivalent, or a mild soap solution to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue. Cleaning Interior Trim Interior trim should be cleaned starting with a damp cloth, a damp cloth with MOPAR威 Total Clean or equivalent, then MOPAR威 Spot & Stain Remover or equivalent if absolutely necessary. Do not use harsh cleaners or • For grease stains, apply MOPAR威 Multi-Purpose Armor All威.
468 MAINTAINING YOUR VEHICLE solvents, detergents, or ammonia-based cleaners to clean To minimize the possibility of scratching the lenses and your leather upholstery. Application of a leather condi- reducing light output, avoid wiping with a dry cloth. To tioner is not required to maintain the original condition. remove road dirt, wash with a mild soap solution followed by rinsing. WARNING! Do not use volatile solvents for cleaning purposes.
MAINTAINING YOUR VEHICLE 469 Replace the seat belts if they appear frayed or worn, or if Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are the buckles do not work properly. molded in clear plastic. When cleaning the lenses, care Cleaning the Instrument Panel Cupholders must be taken to avoid scratching the plastic. Removal 1. Clean with a wet soft rag.
470 MAINTAINING YOUR VEHICLE Installation Place the liner into the cupholder drawer and press the liner into place so that the retention tabs seat into the corresponding openings in the drawer. FUSES Totally Integrated Power Module (TIPM) The Totally Integrated Power Module (TIPM) is located in the engine compartment near the battery. Refer to the applicable “Engine Compartment” illustration in this section. This center contains cartridge fuses and minifuses.
MAINTAINING YOUR VEHICLE 471 The numbers inside the TIPM cover correspond to the following table. CAUTION! • When installing the Totally Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
472 MAINTAINING YOUR VEHICLE Cavity J7 FUSES/TIPM Cartridge Mini-Fuse Fuse 30 Amp — Pink J8 40 Amp Green — J9 40 Amp Green — 30 Amp Pink — J10 Description Antilock Brakes Valve/Stability Control System Power Memory Seat – If Equipped Partial Zero Emissions Vehicle Motor/ Flex Fuel Headlamp Wash Relay/ Manifold Tuning Valve Cavity J11 FUSES/TIPM Cartridge Mini-Fuse Fuse 30 Amp — Pink — Power Sliding Door Module/ Anti–Theft Module Relay Lock Feed Ignition Off Draw (IOD) – Main Rear Window Def
MAINTAINING YOUR VEHICLE Cavity J19 J20 J21 J22 M1 FUSES/TIPM Cartridge Mini-Fuse Fuse 60 Amp Yel- — low 30 Amp — Pink 20 Amp — Blue 25 Amp — Natural — 15 Amp Blue M2 M3 — — M4 — Description Radiator Fan Front Wiper LO/HI Front/Rear Washer Sunroof Module Rear Center Brake Lamp/ Brake Switch — — 20 Amp Yel- Spare Fuse low 10 Amp Red Trailer Tow Cavity M5 M6 M7 M8 M9 I nf or mat i onPr ov i dedby : 473 FUSES/TIPM Cartridge Mini-Fuse Description Fuse — 25 Amp Inverter Natural — 20 Amp Yel- Power Ou
474 MAINTAINING YOUR VEHICLE Cavity M10 FUSES/TIPM Cartridge Mini-Fuse Fuse — 15 Amp Blue M11 — M12 — Description Ignition Off Draw — Video System, Satellite Radio, DVD, HandsFree Module, Universal Garage Door Opener, Vanity Lamp, Streaming Video Module 10 Amp Red Ignition Off Draw – Climate Control System 30 Amp Amplifier Green (AMP)/Radio Cavity M13 M14 I nf or mat i onPr ov i dedby : FUSES/TIPM Cartridge Mini-Fuse Description Fuse — 20 Amp Yel- Ignition Off low Draw— Instrument Cluster, SIRE
MAINTAINING YOUR VEHICLE Cavity M15 FUSES/TIPM Cartridge Mini-Fuse Description Fuse — 20 Amp Yel- Rear View Mirlow ror, Instrument Cluster, MultiFunction Control Switch, Tire Pressure Monitor, Glow Plug Module – Export Diesel Only, AssyShifter (Hall Effect), Acoustic Noise Cancellation Cavity M16 M17 M18 M19 I nf or mat i onPr ov i dedby : 475 FUSES/TIPM Cartridge Mini-Fuse Description Fuse — 10 Amp Red Airbag Module/ Occupant Classification Module — 15 Amp Left Tail/ Blue License/Park Lamp, Running
476 MAINTAINING YOUR VEHICLE Cavity M20 FUSES/TIPM Cartridge Mini-Fuse Fuse — 15 Amp Blue M21 — M22 — M23 — M24 — Description Instrument Cluster Interior Light, Switch Bank, Steering Column Module, Switch Steering Wheel 20 Amp Yel- Automatic low Shutdown #3 10 Amp Red Right Horn (HI/LOW) 10 Amp Red Left Horn (HI/ LOW) 25 Amp Rear Wiper Natural Cavity M25 M26 M27 I nf or mat i onPr ov i dedby : FUSES/TIPM Cartridge Mini-Fuse Description Fuse — 20 Amp Yel- Fuel Pump, low Diesel Lift Pump – Ex
MAINTAINING YOUR VEHICLE Cavity M28 M29 M30 M31 FUSES/TIPM Cartridge Mini-Fuse Description Fuse — 10 Amp Red Powertrain Control Module, Transmission Feed, Transmission Control Module — 10 Amp Red Occupant Classification Module — 15 Amp Rear Wiper Blue Module, Power Folding Mirror, J1962 Diagnostic Feed — 20 Amp Yel- Back-Up Lamps low Cavity M32 M33 I nf or mat i onPr ov i dedby : 477 FUSES/TIPM Cartridge Mini-Fuse Description Fuse — 10 Amp Red Airbag Module, TT EUROPE — 10 Amp Red Powertrain Control
478 MAINTAINING YOUR VEHICLE Cavity M34 M35 M36 FUSES/TIPM Cartridge Mini-Fuse Description Fuse — 10 Amp Red Park Assist, Heater Climate Control System Module, Headlamp Wash, Compass, IR Sensor, Rear Camera, Lamp Door FT Drv/ Pass, Lamp Flashlight, AHLM, Relay Diesel Cabin Heater, Rad Fan Diesel — 10 Amp Red Heated Mirrors — 20 Amp Yel- Power Outlet low #3 Cavity M37 M38 FUSES/TIPM Cartridge Mini-Fuse Description Fuse — 10 Amp Red Antilock Brakes, Stability Control System, Stop Lamp Switch, Fuel Pump
MAINTAINING YOUR VEHICLE 479 system lubrication to minimize the possibility of combreaker located under the instrument panel near the pressor damage when the system is started again. steering column. If you experience temporary or permanent loss of these systems, see your authorized dealer for REPLACEMENT BULBS service. VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days, you may want to take steps to protect your battery.
480 MAINTAINING YOUR VEHICLE All of the interior bulbs are glass wedge base or glass BULB REPLACEMENT cartridge types. Aluminum base bulbs are not approved High Intensity Discharge Headlamps (HID) — If and should not be used for replacement. Equipped The headlamps are a type of high voltage discharge tube. LIGHT BULBS – Exterior Bulb Number High voltage can remain in the circuit even with the Backup, Tail, Stop Lamp . . . . . . . . . . . . . . . . . . . 3157 headlamp switch off and the key removed.
MAINTAINING YOUR VEHICLE NOTE: On vehicles equipped with High Intensity Discharge (HID) headlamps, when the headlamps are turned on, there is a blue hue to the lamps. This diminishes and becomes more white after approximately 10 seconds, as the system charges. Quad Headlamps 1. Raise the hood to access the high or low beam bulbs at the rear of the headlamp housing. 481 CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life.
482 MAINTAINING YOUR VEHICLE 1. From behind the bumper fascia, or the access panel on the air dam, twist the bulb counterclockwise, and remove 1. Raise the hood to access the rear of the headlamp bulb. housing. Front Side Marker Lamp NOTE: Access is somewhat limited. You may have to remove the inner fender well or remove the headlamp housing for bulb replacement. 2. Twist the socket and remove from the headlamp housing, then pull the bulb out. CAUTION! Do not touch the new bulb with your fingers.
MAINTAINING YOUR VEHICLE 483 2. Remove the tail lamp assembly by removing the two NOTE: screws from the inboard side. Use a fiber stick or similar • If a screwdriver is used, make sure a soft material is placed between the vehicle body and tool so not to tool to gently pry the light on the outboard side to scratch the paint. disengage the two ball studs. • The PRY location is best closest to the studs while dislodging them separately.
484 MAINTAINING YOUR VEHICLE 5. Replace the bulb, reinstall the socket, and reattach the lamp assembly. Center High-Mounted Stop Lamp (CHMSL) The CHMSL uses LED lamps that are not serviceable separately. The CHMSL must be replaced as an assembly, see your authorized dealer. License Lamp The license plate lamp is located under the tailgate light bar and above the license plate. Bulb Location 1 — Stop, Tail, Turn Signal Bulb Combo 2 — Backup Bulb 1.
MAINTAINING YOUR VEHICLE 485 FLUID CAPACITIES U.S. Metric Fuel (Approximate) 20 Gallons 76 Liters Engine Oil with Filter 3.3L and 3.8L Engine (SAE 5W-20, API Certified) 5 Quarts 4.7 Liters 4.0L Engine (SAE 10W-30, API Certified) 5.5 Quarts 5.2 Liters Cooling System * 3.3L, 3.8L, and 4.0L Engine (MOPAR威 Engine Coolant/ 13.4 Quarts 12.6 Liters Antifreeze 5 Year/100,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level. Add 2.9 Qts (2.
486 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant Five Year/100,000 Mile Formula HOAT Engine Coolant (Hybrid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Engine Oil – 3.3L and 3.8L Engines Chrysler Material Standard MS-6395. Refer to your oil filler cap for correct SAE grade.
MAINTAINING YOUR VEHICLE 487 Chassis Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. MOPAR威 DOT 3 and SAE J1703 should be used or equivalent. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. MOPAR威 Power Steering Fluid +4, MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product.
I nf or mat i onPr ov i dedby :
M A I N T E N A N C ▫ Required Maintenance Intervals . . . . . . . . . . 492 E MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 490 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 490 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichever comes first.
M A I N T E N A N C E 492 MAINTENANCE SCHEDULES • Inspect the battery and clean and tighten the terminals Required Maintenance Intervals Refer to the Maintenance Schedules on the following as required. pages for the required maintenance intervals. • Check the fluid levels of the coolant reservoir, the brake master cylinder, the power steering and the transmission and add as needed. • Check all lights and other electrical items for correct operation.
MAINTENANCE SCHEDULES 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 493 M 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions.
M 494 MAINTENANCE SCHEDULES A I 18,000 Miles (30,000 km) or N T 18 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ Replace the air conditioning filter.
MAINTENANCE SCHEDULES 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ Replace the air conditioning filter. ❏ Inspect the brake linings, replace if necessary.
M 496 MAINTENANCE SCHEDULES A I 42,000 Miles (70,000 km) or N T 42 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ Replace the air conditioning filter.
MAINTENANCE SCHEDULES 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the air conditioning filter. Inspect the brake linings, replace if necessary. Change the automatic transmission fluid & filter if using your vehicle for any of the following: police, taxi, fleet or frequent trailer towing.
M 498 MAINTENANCE SCHEDULES A I 66,000 Miles (110,000 km) or N T 66 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ Replace the air conditioning filter.
MAINTENANCE SCHEDULES 78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ Replace the air conditioning filter. ❏ Inspect the brake linings, replace if necessary.
M 500 MAINTENANCE SCHEDULES A I 90,000 Miles (150,000 km) or N T 90 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C ❏ Replace the engine air cleaner filter. E S C H E D U L E S 8 96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Inspect and replace the PCV Valve if necessary.† Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code ❏ Change the engine oil and engine oil filter.
MAINTENANCE SCHEDULES 102,000 Miles (170,000 km) or 102 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the ignition cables (3.3L and 3.8L engines). ❏ Replace the spark plugs (3.3L, 3.8L, and 4.0L engines). ❏ Replace the timing belt (4.0L engine). ❏ Flush and replace the engine coolant if not done at 60 months.
M 502 MAINTENANCE SCHEDULES A I 114,000 Miles (190,000 km) or N T 114 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the air conditioning filter.
MAINTENANCE SCHEDULES 126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 503 M 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions.
M 504 MAINTENANCE SCHEDULES A I 138,000 Miles (230,000 km) or N T 138 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions.
MAINTENANCE SCHEDULES 505 M A 150,000 Miles (250,000 km) or 150 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. Odometer Reading Repair Order # † This maintenance is recommended by the manufac- I turer, but is not required to maintain emissions warranty. N WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment.
I nf or mat i onPr ov i dedby :
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 511 ▫ Prepare For The Appointment . . . . . . . . . . . 509 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 511 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 509 䡵 Warranty Information . . . . . . . . . . . . . . . . . .
508 IF YOU NEED CONSUMER ASSISTANCE 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 515 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 515 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 515 ▫ Temperature Grades . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 509 the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the for an appointment. right papers with you. Take your warranty folder. All work to be performed may not be covered by the IF YOU NEED ASSISTANCE warranty.
510 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized • Vehicle delivery date and mileage dealer’s service manager first. Most matters can be reChrysler Group LLC Customer Center solved with this process. P.O. Box 21–8004 • If for some reason you are still not satisfied, talk to the Auburn Hills, MI 48321–8004 general manager or owner of the authorized dealer- Phone: (800) 247–9753 ship. They want to know if you need assistance. Chrysler Canada Inc.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
512 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE 513 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. In Canada If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately.
514 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals • Owner’s Manuals These comprehensive Service Manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing Chrysler Group LLC vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts.
IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. 515 significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
516 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10 I nf or mat i onPr ov i dedby :
518 INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . 455 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 387 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 452 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 381 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 172 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 444 Air Conditioner Maintenance . . . . . . . . . . . . . . . 448 Air Conditioning . . . . . . . . . . . . . . .
INDEX 519 Blind Spot Monitoring . . . . . . . . . . . . . . . . . . . . 117 Body Mechanism Lubrication . . . . . . . . . . . . . . . 451 B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . 357 Brake Assist System . . . . . . . . . . . . . . . . . . . . . . 349 Brake Control System, Electronic . . . . . . . . . . . . . 347 Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 487 Brake, Parking . . . . . . . . . . . . . . . . . . . . . . . . . . 343 Brake System . . . . . . . .
520 INDEX Caps, Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387 Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . 443 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 342 Radiator (Coolant Pressure) . . . . . . . . . . . . . . . 456 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465 Carbon Monoxide Warning . . . . . . . . . . . . . . 101,383 Cargo Compartment Luggage Carrier . . . . . . . . . . . . . . . . . . . . . . .
INDEX Connector UCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289 Universal Consumer Interface (UCI) . . . . . . . . . 289 Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 Console, Floor . . . . . . . . . . . . . . . . . . . . . . . . . . 215 Console, Overhead . . . . . . . . . . . . . . . . . . . . . . . 189 Console, Removable . . . . . . . . . . . . . . . . . . . . . . 219 Contract, Service . . . . . . . . . . . . . . . . . . . . . . . .
522 INDEX Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 444 Domelight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . 33 Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 192 Driving On Slippery Surfaces . . . . . . . . . . . . . . . . . . . 338 Through Flowing, Rising, or Shallow Standing Water . . . . . . . . . . . . . . . . .
INDEX 523 Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 444 Air Conditioning . . . . . . . . . . . . . . . . . . . . 322,449 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 444,486 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . 444 Flashers Hazard Warning . . . . . . . . . . . . . . . . . . . . . . . 412 Turn Signal . . . . . . . . . . . . . . . . . . . . . . . . 104,236 Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . . . . .
524 INDEX Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 485 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Fluid Level Checks Automatic Transaxle . . . . . . . . . . . . . . . . . . . . 463 Automatic Transmission . . . . . . . . . . . . . . . . . 462 Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 342 Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 525 Time Delay . . . . . . . . . . . . . . . . . . . . . . . . . . 163 Washers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 Heated Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . 115 Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 Heater, Engine Block . . . . . . . . . . . . . . . . . . . . . 329 High Beam/Low Beam Select (Dimmer) Switch . . 166 Hitches Trailer Towing . . . . .
526 INDEX Information Center, Vehicle . . . . . . . . . . . . . . . . . 250 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . 112 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . . 233 Instrument Panel and Controls . . . . . . . . . . . . . . 231 Instrument Panel Cover . . . . . . . . . . . . . . . . . . . 467 Instrument Panel Lens Cleaning . . . . . . . . . . . . . 469 Integrated Power Module (Fuses) . . . . . . . . . . . . 470 Interior Appearance Care . . . . . . . . . . . . .
INDEX Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482 Battery Saver . . . . . . . . . . . . . . . . . . . . . . . . . 164 Brake Assist Warning . . . . . . . . . . . . . . . . . . . 351 Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . 237 Bulb Replacement . . . . . . . . . . . . . . . . . . . 479,480 Center Mounted Stop . . . . . . . . . . . . . . . . . . . 484 Daytime Running . . . . . . . . . . . . . . . . . . . . . . 164 Dimmer Switch, Headlight . . . . . . . . . . . . .
528 INDEX Warning (Instrument Cluster Description) . . . . . 233 Load Leveling System . . . . . . . . . . . . . . . . . . . . 221 Loading Vehicle . . . . . . . . . . . . . . . . . . . 214,389,392 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . 392 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357 Locks Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 529 New Vehicle Break-In Period . . . . . . . . . . . . . . . . 100 Onboard Diagnostic System . . . . . . . . . . . . . . 437,438 Opener, Garage Door (HomeLink威) . . . . . . . . . . . 192 Occupant Restraints . . . . . . . . . . . . . . . . . . . 52,75,79 Operator Manual (Owner’s Manual) . . . . . . . . . . . . 4 Occupant Restraints (Sedan) . . . . . . . . . . . 71,72,75,78 Outside Rearview Mirrors . . . . . . . . . . . . . . . 112,113 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . .
530 INDEX Radiator Cap (Coolant Pressure Cap) . . . . . . . 453,456 Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . 302 Radio Remote Controls . . . . . . . . . . . . . . . . . . . . 300 Radio, Satellite (Uconnect威 studios) . . . . . . . . 294,298 Rear Air Conditioning . . . . . . . . . . . . . . . . . 309,317 Rear Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 Rear Cross Path . . . . . . . . . . . . . . . . . . . . . . . . . 123 Rear Heater . . . . . . . . . . . . . . . .
INDEX Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 440 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . 367 Reporting Safety Defects . . . . . . . . . . . . . . . . . . . 512 Resetting Oil Change Indicator . . . . . . . . . 244,246,254 Restraint, Head . . . . . . . . . . . . . . . . . . . . . . . . . 132 Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . 87,92 Restraints, Infant . . . . . . . . . . . . . . . . . . . . . . . . . 87 Rocking Vehicle When Stuck .
532 INDEX Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Stow ⬘n Go (Fold in Floor) . . . . . . . . . . . . . . . 136 Tilting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Security Alarm (Theft Alarm) . . . . . . . . . . . . . . . . 16 Selection of Coolant (Antifreeze) . . . . . . . . . . 454,486 Sentry Key (Immobilizer) . . . . .
INDEX Steering Wheel Mounted Sound System Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207,479 Storage Bin . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 Storage, Vehicle . . . . . . . . . . . . . . . . . . . . . . 321,479 Storing Your Vehicle . . . . . . . . . . . . . . . . . . . . . . 479 Stow ⬘n Go (Fold in Floor) Seats . . . . . . . . . . . . . 136 Sun Roof . . . . . . . . . . . . . . . . . . . . .
534 INDEX Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 367 Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 352,361 Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 368 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 414 Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 535 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 245 Video Entertainment System™ Turn Signals . . . . . . . . . . . . . . . . . . . 165,236,481,482 (Rear Seat Video System) . . . . . . . . . . . . . . . . . . 298 Voice Recognition System (VR) . . . . . . . . . . . . . . 126 UCI Connector . . . . . . . . . . . . . . . . . . . . . . . . . 289 Uconnect™ (Hands-Free Phone) . . . . . . . . . . . . . 125 Warning Flasher, Hazard . . . . . . . . . . . . . . . . . . 412 Umbrella Holder .
536 INDEX Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Windshield Wiper Blades . . . . . . . . . . . . . . . . . . 451 Rear Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Wiper Blade Replacement . . . . . . . . . . . . . . . . . . 451 Windows, Express Down . . . . . . . . . . . . . . . . . . . 22 Windshield Defroster . . . . . . . . . . . . . . . . . . . . . 103 Zone Control (Temperature Control) . . . . . . . . . . 307 Windshield Washers . . . . . . . . . . . .
Chrysler Group LLC 10Y531-126-AC 3rd Edition I nf or mat i onPr ovi dedby : Printed in U.S.A.
