Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide April 2005 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
CONTENTS Preface ix Objectives Audience ix ix Organization ix Conventions x Related Publications xii Obtaining Documentation xii Cisco.
Contents Access Point Configuration 1-8 Workgroup Bridge Configuration 1-9 CHAPTER 2 Installation Overview 2-1 Safety Warnings 2-2 All Installations 2-2 Outdoor and Vehicle Installations Vehicle Bridge Installations 2-3 2-3 Safety Information 2-3 FCC Safety Compliance Statement 2-3 Safety Precautions 2-4 Typical Outdoor Installation Components Installation Guidelines Site Surveys 2-5 2-6 Unpacking the Access Point/Bridge Package Contents 2-6 Before Beginning the Installation Installation Summary
Contents CHAPTER 5 Configuring the Access Point/Bridge for the First Time Before You Start 5-1 5-2 Resetting the Access Point/Bridge to Default Settings Default IP Address Behavior Default SSID and Default Role 5-2 5-2 5-3 Obtaining and Assigning an IP Address 5-3 Connecting to the Access Point/Bridge Locally 5-3 Using the Power Injector’s Ethernet Port 5-3 Using the Power Injector’s Console Port 5-4 Assigning Basic Settings 5-4 Default Settings on the Express Setup Page Enabling the Radio Interf
Contents Enabling and Disabling Editing Features 6-8 Editing Commands Through Keystrokes 6-8 Editing Command Lines That Wrap 6-9 Searching and Filtering Output of show and more Commands Assigning an IP Address Using the CLI 6-11 Finding the Access Point/Bridge IP Address Using the CLI CHAPTER Troubleshooting 7 Checking Power 6-11 7-1 Checking the LEDs 7-2 Normal Mode LED Indications Power Injector 6-10 7-2 7-5 7-6 Checking Basic Configuration Settings 7-6 Default IP Address Behavior 7-6 Defaul
Contents Statement 1022—Disconnect Device A-7 Statement 1024—Ground Conductor A-9 Statement 1030—Equipment Installation A-10 Statement 1033—SELV-IEC 60950 DC Power Supply Statement 1040—Product Disposal APPENDIX B A-12 A-13 Statement 1052—Installing and Grounding the Antenna A-15 Declarations of Conformity and Regulatory Information B-1 Manufacturers Federal Communication Commission Declaration of Conformity Statement B-2 Department of Communications—Canada B-3 Canadian Compliance Statemen
Contents APPENDIX F Load-Dump Protection for Transportation Vehicles Load-Dump Protection F-1 F-1 GLOSSARY INDEX Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide viii OL-5048-02
Preface This section describes the objectives, audience, organization, and conventions of the Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide. Objectives This publication explains the steps for initial setup and basic configuration of the Cisco Aironet 1300 Series Outdoor Access Point/Bridge supporting 2.4-GHz operation. This publication also provides troubleshooting information and detailed specifications.
Preface Conventions Appendix A, “Translated Safety Warnings,” lists translations of the safety warnings in this publication. Appendix B, “Declarations of Conformity and Regulatory Information,” describes the regulatory conventions to which the access point/bridge conforms and provides guidelines for operating access point/bridges in Japan. Appendix C, “Access Point/Bridge Specifications,” describes the channels and antenna settings supported by the regulatory organizations.
Preface Conventions Attention Ce symbole d’avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures. Avant d’accéder à cet équipement, soyez conscient des dangers posés par les circuits électriques et familiarisez-vous avec les procédures courantes de prévention des accidents. Pour obtenir les traductions des mises en garde figurant dans cette publication, veuillez consulter l’annexe intitulée « Translated Safety Warnings » (Traduction des avis de sécurité).
Preface Related Publications Related Publications For more information about access point/bridges and related products, refer to the following publications: • Quick Start Guide: Cisco Aironet 1300 Series Outdoor Access Point/Bridge describes the access point/bridge, system components, and how to obtain documentation. This document is included in the shipping box with your access point/bridge.
Preface Documentation Feedback You can access the Cisco website at this URL: http://www.cisco.com You can access international Cisco websites at this URL: http://www.cisco.com/public/countries_languages.shtml Documentation DVD Cisco documentation and additional literature are available in a Documentation DVD package, which may have shipped with your product. The Documentation DVD is updated regularly and may be more current than printed documentation.
Preface Cisco Product Security Overview Cisco Product Security Overview Cisco provides a free online Security Vulnerability Policy portal at this URL: http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html From this site, you can perform these tasks: • Report security vulnerabilities in Cisco products. • Obtain assistance with security incidents that involve Cisco products. • Register to receive security information from Cisco.
Preface Obtaining Technical Assistance Cisco Technical Support Website The Cisco Technical Support Website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, 365 days a year, at this URL: http://www.cisco.com/techsupport Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password.
Preface Obtaining Technical Assistance The power injector serial number is located on the bottom of the cabinet (refer to Figure 2).
Preface Obtaining Additional Publications and Information Definitions of Service Request Severity To ensure that all service requests are reported in a standard format, Cisco has established severity definitions. Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.
Preface Obtaining Additional Publications and Information • World-class networking training is available from Cisco. You can view current offerings at this URL: http://www.cisco.com/en/US/learning/index.
C H A P T E R 1 Overview The Cisco Aironet 1300 Series Outdoor Access Point/Bridge (hereafter called the access point/bridge) is a wireless device designed for building-to-building wireless connectivity. Operating in the 2.4-GHz band (2.400 to 2.497 GHz), using the IEEE 802.11g standard, the access point/bridge delivers 1 to 54 Mbps data rates without the need for a license.
Chapter 1 Overview Key Features Key Features Key features of the access point/bridge: • Unlicensed IEEE 802.11g 2.
Chapter 1 Overview Key Features Note Antenna connectors are available only on the external antenna access point/bridge configuration. Power The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle.
Chapter 1 Overview Key Features External Antenna The access point/bridge is available in an external antenna configuration (see Figure 1-1) for use with Cisco Aironet 2.4-GHz antennas. Two reverse-TNC type RF connectors are provided on the end of the unit to support single or diversity antenna configurations. The antennas connect to the access point/bridge antenna connectors using a coax cable. These are some of the external antennas supported by the access point/bridge: Note • 5.
Chapter 1 Overview Key Features Access Point/Bridge Connector Locations 1 4 2 3 5 117060 Figure 1-2 1 Ground lug mounting screws 3 Mounting posts 2 Left antenna connector (external antenna access point/bridge configuration only) 4 LEDs Primary right antenna connector (external antenna access point/bridge configuration only) 5 Dual-coax Ethernet ports (F-Type connectors) LEDs Four LEDs are located on back of the housing to report installation and alignment conditions, status, radio activ
Chapter 1 Overview Key Features • The install LED indicates that installation mode is activated. During installation mode, the other LEDs provide signal strength readings used for antenna alignment. • The radio LED blinks green to indicate radio traffic activity. The light is normally off, but it blinks green whenever a packet is received or transmitted over the radio link. This LED also provides signal strength readings during installation mode. • The status LED indicates association status.
Chapter 1 Overview Network Configuration Examples Network Configuration Examples This section describes the access point/bridge’s role in five common wireless network configurations. Point-to-Point Bridge Configuration In a point-to-point bridge configuration, two bridges connect two remote LAN networks using a wireless communication link (see Figure 1-4). The bridge connected to the main LAN network is classified as a root bridge and the other bridge is classified as a non-root bridge.
Chapter 1 Overview Network Configuration Examples Point-to-Multipoint Bridge Configuration The point-to-multipoint bridge configuration (Figure 1-6) connects the main LAN network to multiple remote LAN networks. Wireless devices can also connect to the root bridge. Point-to-Multipoint Bridge Configuration 117021 Figure 1-6 Access Point Configuration When configured in access point mode, the unit can support remote workgroup bridges and local wireless client devices (see Figure 1-7).
Chapter 1 Overview Network Configuration Examples Workgroup Bridge Configuration When configured in the workgroup bridge mode, the unit provides a wireless connection for remote wired devices to a Cisco Aironet access point (see Figure 1-8) or to a Cisco Aironet bridge (see Figure 1-9).
Chapter 1 Overview Network Configuration Examples Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide 1-10 OL-5048-02
C H A P T E R 2 Installation Overview This chapter provides warnings, safety information, and information needed before you begin the installation of your access point/bridge system.
Chapter 2 Installation Overview Safety Warnings Safety Warnings Translated versions of the following safety warnings are provided in Appendix A, “Translated Safety Warnings.” All Installations Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.
Chapter 2 Installation Overview Safety Information Warning Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, as they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (e.g. U.S.
Chapter 2 Installation Overview Safety Information Safety Precautions Warning Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, as they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (e.g. U.S.
Chapter 2 Installation Overview Installation Guidelines Typical Outdoor Installation Components The access point/bridge is designed to be installed in an outdoor environment, typically on a tower or a tall building. A typical installation diagram is shown in Figure 2-1.
Chapter 2 Installation Overview Site Surveys Site Surveys Every network application is a unique installation. Before installing multiple access point/bridges, you should perform a site survey to determine the optimum use of networking components and to maximize range, coverage, and network performance. Consider the following operating and environmental conditions when performing a site survey: • Data rates—Sensitivity and range are inversely proportional to data bit rates.
Chapter 2 Installation Overview Before Beginning the Installation The optional roof mount kit contains these items: • One roof-wall mount • Two dual-coax cables [20 ft (6.1 m) and 50 ft (15.
Chapter 2 Installation Overview Before Beginning the Installation Access Point/Bridge Layout 1 4 2 5 3 117060 Figure 2-2 1 Grounding studs 4 LEDs 2 Antenna connectors 5 Dual-coax Ethernet ports (F-Type connectors) 3 Mounting lugs Power Injector Indicators and Connectors R T O C IN O 117189 R C E IS O W P C JE A IR O N E T Figure 2-3 4 5 3 1 1 2 1 Dual-coax Ethernet ports (F-Type connectors) 4 Ethernet LAN port (RJ-45 connector) 2 Power LED 5 Console serial p
Chapter 2 Installation Overview Installation Summary Figure 2-4 Power Module 3 2 88829 1 1 48-VDC power output cable 2 Power module Figure 2-5 3 AC power cord 2 Ground wire lug Grounding Block 1 2 88830 1 1 F-type coaxial connectors Installation Summary Caution Note You should read and carefully follow the installation instructions before connecing the system to its power source. The access point/bridge and power injector can be damaged by incorrect power application.
Chapter 2 Installation Overview Installation Summary • Warning Warning For outdoor installations, connect the dual-coax Ethernet cables between the power injector and the grounding block. For indoor installations, connect the dual-coax cables to the power injector. Tip You can connect the dual-coax cable connectors to either of the grounding block connectors or the power injector’s dual-coax Ethernet ports.
Chapter 2 Installation Overview Installation Summary • Seal all external connectors with special weather sealing material. Configure security and other access point/bridge options. For additional information, refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Bridges or to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points.
Chapter 2 Installation Overview Installation Summary Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide 2-12 OL-5048-02
C H A P T E R 3 Mounting and Alignment Overview This chapter provides an overview of the access point/bridge mounting and bridge antenna alignment.
Chapter 3 Mounting and Alignment Overview Mounting the Access Point/Bridge Mounting the Access Point/Bridge Typically, the access point/bridge is installed on a rooftop, mast, tower, wall, or a suitable flat surface. Each of these installations requires a different approach. This document provides a mounting overview. For detailed mounting instructions, refer to the Cisco Aironet 1300 Series Outdoor Access Point/Bridge Mounting Instructions that shipped with your unit.
Chapter 3 Mounting and Alignment Overview Mounting Hardware Window Mounting When a wireless link is deployed through a window, significant signal loss can be introduced by the window. Typical losses range from 5 to15 dB per window, depending upon the type of glass. You should take this extra loss into account when planning antenna gains and power settings. A thorough site survey is critical for deployments through windows.
Chapter 3 Mounting and Alignment Overview Mounting Hardware Figure 3-1 Multi-Function Mount 117119 2 1 1 Access point/bridge bracket with support pins 2 Mast bracket Access Point/Bridge Bracket The access point/bridge bracket mounts on the back side of the unit housing. The bracket mounts on four lugs on the unit. The bracket contains two support pins that are used to suspend the unit in the notches on the mast mounting bracket until you secure the mounting bolts.
Chapter 3 Mounting and Alignment Overview LEDs LEDs The LEDs indicate the startup status, operating mode, association status, and received signal strength. This information simplifies the process of activating the link and positioning the antenna from the access point/bridge mounting location. The LEDs are mounted on the back of the housing (see Figure 3-2).
Chapter 3 Mounting and Alignment Overview LEDs The Install LED provides bridge association status during installation mode as shown in Table 3-2. Table 3-2 Install LED Status Install LED Status Bridge State Off Self test Startup. Amber blinking Non-root, searching Not associated (non-root mode). The access point/bridge attempts to associate with a root bridge for 60 seconds1. Amber Non-root, associated Associated (non-root mode). Green blinking Root, searching Not associated (root mode).
Chapter 3 Mounting and Alignment Overview Aligning the Bridge Antenna Using RSSI LED Indications Aligning the Bridge Antenna Using RSSI LED Indications You can align the integrated antenna using LEDs after the unit successfully associates with a remote bridge. In the installation mode before association to another bridge, the Install LED blinks amber. If the unit associates to a root bridge, the Install LED turns amber.
Chapter 3 Mounting and Alignment Overview Aligning the Bridge Antenna Using RSSI LED Indications Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide 3-8 OL-5048-02
C H A P T E R 4 Using the Web-Browser Interface This chapter describes the web-browser interface that you can use to configure the access point/bridge. The web-browser interface contains management pages that you use to change access point/bridge settings, upgrade firmware, and monitor and configure other wireless devices on the network.
Chapter 4 Using the Web-Browser Interface Using the Web-Browser Interface Management Pages Using the Web-Browser Interface Management Pages The access point/bridge management pages use consistent techniques to present and save configuration information. A navigation bar is on the left side of the page, and configuration action buttons appear at the bottom.
Chapter 4 Using the Web-Browser Interface Using the Web-Browser Interface Management Pages Using Action Buttons Table 4-1 lists the page links and buttons that appear on most management pages.
Chapter 4 Using the Web-Browser Interface Using the Web-Browser Interface Management Pages Character Restrictions in Entry Fields Because the access point/bridge uses Cisco IOS software, there are certain characters that you cannot use in the entry fields on the web-browser interface. Table 4-2 lists the prohibited characters and the fields in which you cannot use them.
Chapter 4 Using the Web-Browser Interface Connecting Locally to the Ethernet Port Connecting Locally to the Ethernet Port If you need to configure the access point/bridge locally (without connecting to a wired LAN), you can connect a PC to the power injector’s Ethernet port using a Category 5 Ethernet cable. Note You do not need a special crossover cable to connect your PC to the power injector’s Ethernet port; you can use either a straight-through cable or a crossover cable.
Chapter 4 Using the Web-Browser Interface Connecting Locally to the Ethernet Port Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide 4-6 OL-5048-02
C H A P T E R 5 Configuring the Access Point/Bridge for the First Time This chapter describes how to configure basic settings on your access point/bridge for the first time using the web-browser interface.
Chapter 5 Configuring the Access Point/Bridge for the First Time Before You Start Before You Start Before you install the access point/bridge, make sure you are using a computer connected to the same network as the access point/bridge, and obtain the following information from your network administrator: • A system name or host name for the access point/bridge • The case-sensitive wireless service set identifier (SSID) for your radio network • If not connected to a DHCP server, a unique IP address f
Chapter 5 Configuring the Access Point/Bridge for the First Time Default SSID and Default Role When you connect an access point/bridge running Cisco IOS Release 12.2(15)JA or earlier software with a default configuration to your LAN, the access point/bridge requests an IP address from your DHCP server and, if it does not receive an IP address, the access point/bridge assigns a default IP address of 10.0.0.1. Default SSID and Default Role In Cisco IOS Release 12.
Chapter 5 Configuring the Access Point/Bridge for the First Time Connecting to the Access Point/Bridge Locally Connecting to the Access Point/Bridge Locally Using the Power Injector’s Ethernet Port You can use the power injector’s Ethernet port to configure the access point/bridge locally (without connecting to a wired LAN) using the web-browser or CLI interfaces.
Chapter 5 Configuring the Access Point/Bridge for the First Time Assigning Basic Settings Assigning Basic Settings After you obtain the access point/bridge IP address, you can browse to its Express Setup page and perform an initial configuration. Follow these steps: Step 1 Browse to the access point/bridge IP address. An Enter Network Password window displays. Step 2 Enter the case-sensitive username Cisco in the Username field.
Chapter 5 Configuring the Access Point/Bridge for the First Time Assigning Basic Settings Step 4 Click Express Setup. The Express Setup page displays. Figure 5-2 shows the Express Setup page. Figure 5-2 Step 5 Express Setup Page Enter the configuration settings you obtained from your system administrator. The configurable settings include: • System Name or Host Name—The system name or host name, while not an essential setting, helps identify the access point/bridge on your network.
Chapter 5 Configuring the Access Point/Bridge for the First Time Assigning Basic Settings • IP Subnet Mask—Enter the IP subnet mask provided by your network administrator so that the IP address can be recognized on the LAN. If DHCP is enabled, leave this field blank. • Default Gateway—Enter the default gateway IP address provided by your network administrator. If DHCP is enabled, leave this field blank.
Chapter 5 Configuring the Access Point/Bridge for the First Time Assigning Basic Settings • Step 6 Aironet Extensions—Enable this setting if there are only Cisco Aironet devices on your wireless LAN and the unit is operating as an access point or workgroup bridge. Click Apply to save your settings. If you changed the IP address, you lose your connection to the access point/bridge. Browse to the new IP address to reconnect to the access point/bridge.
Chapter 5 Configuring the Access Point/Bridge for the First Time Adjusting Output Power Level Enabling the Radio Interfaces In Cisco IOS Release 12.3(4)JA, the access point/bridge radios are disabled by default, and there is no default SSID. You must create an SSID and enable the radios before the access point/bridge will allow wireless associations from other devices. These changes to the default configuration improve the security of a newly installed access point/bridge.
Chapter 5 Configuring the Access Point/Bridge for the First Time Configuring Basic Security Settings Figure 5-3 shows the Express Security page.
Chapter 5 Configuring the Access Point/Bridge for the First Time Configuring Basic Security Settings Understanding Express Security Settings When the access point/bridge configuration is at factory defaults, the first SSID that you create by using the Express Security page overwrites the default SSID (tsunami), which has no security settings. The SSIDs that you create appear in the SSID table at the bottom of the page. You can create up to 16 SSIDs on the access point/bridge.
Chapter 5 Configuring the Access Point/Bridge for the First Time Configuring Basic Security Settings Table 5-2 Security Types on Express Security Setup Page (continued) Security Type Description Security Features Enabled EAP Authentication This option enables 802.1x authentication (such as LEAP, PEAP, EAP-TLS, EAP-GTC, EAP-SIM, and others) and requires you to enter the IP address and shared secret for an authentication server on your network (server authentication port 1645). Because 802.
Chapter 5 Configuring the Access Point/Bridge for the First Time Finding the IP Address Using the CLI Using the Express Security Page Follow these steps to create an SSID using the Express Security page: Step 1 Type the SSID in the SSID entry field. The SSID can contain up to 32 alphanumeric characters. Step 2 To broadcast the SSID in the access point/bridge beacon, check the Broadcast SSID in Beacon check box.
Chapter 5 Configuring the Access Point/Bridge for the First Time Assigning an IP Address Using the CLI Assigning an IP Address Using the CLI When you connect the access point/bridge to the wired LAN, the access point links to the network using a bridge virtual interface (BVI) that it creates automatically. Instead of tracking separate IP addresses for the access point/bridge’s Ethernet and radio ports, the network uses the BVI.
C H A P T E R 6 Using the Command-Line Interface This chapter describes the IOS command-line interface (CLI) that you can use to configure your access point/bridge.
Chapter 6 Using the Command-Line Interface Connecting to the Console Serial Port Connecting to the Console Serial Port If you need to configure the access point/bridge locally (without connecting to a wired LAN), you can connect a PC to the power injector console serial port using a DB-9 to RJ-45 serial cable.
Chapter 6 Using the Command-Line Interface Using a Telnet Session to Open the CLI http://www.cisco.com/univercd/cc/td/doc/product/wireless/index.htm • Cisco IOS Command Reference for Cisco Aironet Access Points and Bridges describes the IOS commands supported by Cisco Aironet access points and bridges. This document is available on the Cisco CCO web site at the following URL: http://www.cisco.com/univercd/cc/td/doc/product/wireless/index.
Chapter 6 Using the Command-Line Interface IOS Command Modes IOS Command Modes The Cisco IOS user interface is divided into many different modes. The commands available to you depend on which mode you are currently in. Enter a question mark (?) at the system prompt to obtain a list of commands available for each command mode. When you start a session on the access point/bridge, you begin in user mode, often called user EXEC mode. Only a limited subset of the commands are available in user EXEC mode.
Chapter 6 Using the Command-Line Interface Getting Help Getting Help You can enter a question mark (?) at the system prompt to display a list of commands available for each command mode. You can also obtain a list of associated keywords and arguments for any command, as shown in Table 6-2. Table 6-2 Help Summary Command Purpose help Obtains a brief description of the help system in any command mode. abbreviated-command-entry? Obtains a list of commands that begin with a particular character string.
Chapter 6 Using the Command-Line Interface Understanding CLI Messages Configuration commands can also have a default form. The default form of a command returns the command setting to its default. Most commands are disabled by default, so the default form is the same as the no form. However, some commands are enabled by default and have variables set to certain default values. In these cases, the default command enables the command and sets variables to their default values.
Chapter 6 Using the Command-Line Interface Using Command History Changing the Command History Buffer Size By default, the access point/bridge records ten command lines in its history buffer. Beginning in privileged EXEC mode, enter this command to change the number of command lines that the access point/bridge records during the current terminal session: br# terminal history [size number-of-lines] The range is from 0 to 256.
Chapter 6 Using the Command-Line Interface Using Editing Features Using Editing Features This section describes the editing features that can help you manipulate the command line. It contains these sections: • Enabling and Disabling Editing Features, page 6-8 • Editing Commands Through Keystrokes, page 6-8 • Editing Command Lines That Wrap, page 6-9 Enabling and Disabling Editing Features Although enhanced editing mode is automatically enabled, you can disable it.
Chapter 6 Using the Command-Line Interface Using Editing Features Table 6-5 Editing Commands Through Keystrokes (continued) Capability Keystroke Delete entries if you make a mistake Delete or Backspace or change your mind. Ctrl-D Capitalize or lowercase words or capitalize a set of letters. Purpose Erase the character to the left of the cursor. Delete the character at the cursor. Ctrl-K Delete all characters from the cursor to the end of the command line.
Chapter 6 Using the Command-Line Interface Searching and Filtering Output of show and more Commands In this example, the access-list global configuration command entry extends beyond one line. When the cursor reaches the end of the line, the line is shifted ten spaces to the left and redisplayed. The dollar sign ($) shows that the line has been scrolled to the left. Each time the cursor reaches the end of the line, the line is again shifted ten spaces to the left.
Chapter 6 Using the Command-Line Interface Assigning an IP Address Using the CLI Assigning an IP Address Using the CLI When you connect the access point/bridge to the wired LAN, the access point/bridge links to the network using a access point/bridge virtual interface (BVI) that it creates automatically. Instead of tracking separate IP addresses for the access point/bridge’s Ethernet and radio ports, the network uses the BVI.
Chapter 6 Using the Command-Line Interface Finding the Access Point/Bridge IP Address Using the CLI Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide 6-12 OL-5048-02
C H A P T E R 7 Troubleshooting This chapter provides troubleshooting procedures for basic problems with the access point/bridge. For the most up-to-date, detailed troubleshooting information, refer to the CiscoTechnical Support and Documentation website at the following URL: http://www.cisco.com/en/US/products/hw/wireless/tsd_products_support_category_home.
Chapter 7 Troubleshooting Checking the LEDs Checking the LEDs If your access point/bridge is not associating with a remote bridge or access point, check the four LEDs on the back panel. You can use them to quickly assess the unit’s status. For information on using the LEDs during the installation and alignment of the access point/bridge antenna, refer to the “LEDs” section on page 3-5. Figure 7-1 shows the access point/bridge LEDs.
Chapter 7 Troubleshooting Checking the LEDs Table 7-1 LED Indications (continued) Ethernet LED Status LED Radio LED Install LED Meaning — Blinking green — — Root bridge mode—no remote bridges are associated. Non-root bridge mode—not associated to the root bridge. If all bridges are powered up, this could be caused by incorrect SSID and security settings or improper antenna alignment. You should check the SSID and security settings of all bridges and verify antenna alignment.
Chapter 7 Troubleshooting Checking the LEDs The LED blinking error codes are described in Table 7-2. Table 7-2 LED Blinking Error Codes Blinking Codes LED First Digit Second Digit Description Ethernet 2 1 Ethernet cable problem—verify that the cable is properly connected and not defective. This error might also indicate a problem with the Ethernet link. If the cable is connected properly and not defective, contact technical support for assistance.
Chapter 7 Troubleshooting Power Injector Power Injector When the power injector is powered up, it applies 48-VDC to the dual-coax cables to the access point/bridge. When power is applied to the access point/bridge, the unit activates the bootloader and begins the POST operations. The access point/bridge begins to load the Cisco IOS image when the POST operations are successfully completed. Upon successfully loading the image, the unit initializes and tests the radio.
Chapter 7 Troubleshooting Checking Power Checking Power You can verify the availability of power to the access point/bridge by checking the power injector LED (see Figure 7-2): • Power LED – Green color indicates input power is being supplied to the bridge. – Red color indicates an overcurrent or overvoltage error condition—disconnect input power from the power injector, check all coax cable connections for a possible short, wait approximately 1 minute, and reconnect input power to the power injector.
Chapter 7 Troubleshooting Checking Basic Configuration Settings Note In Cisco IOS Release 12.3(4)JA, you must create an SSID and enable the radio before the access point/bridge allows wireless associations from other devices. These changes to the default configuration improve the security of a newly installed access point/bridge.
Chapter 7 Troubleshooting Antenna Alignment Security Settings Remote Cisco Aironet bridges or client devices attempting to authenticate to your access point/bridge must support the same security options configured in the access point/bridge, such as WEP, EAP or LEAP, MAC address authentication, Message Integrity Check (MIC), WEP key hashing, and 802.1X protocol versions.
Chapter 7 Troubleshooting Running the Ping or Link Test Step 3 Choose the radio interface by clicking Radio0-802.11G. The radio status page appears. Step 4 Click the Carrier Busy Test tab and the Carrier Busy Test page appears. Step 5 Click Start to begin the carrier busy test. When the test completes, the results are displayed on the bottom of the page. For each of the channel center frequencies, the test produces a value indicating the percentage of time that the channel is busy.
Chapter 7 Troubleshooting Resetting the Access Point/Bridge to the Default Configuration Resetting the Access Point/Bridge to the Default Configuration You can use the web-browser interface or the CLI to reset the access point/bridge to a factory default configuration. Note The following steps reset all configuration settings to factory defaults, including passwords, WEP keys, the IP address, and the SSID.
Chapter 7 Troubleshooting Reloading the Access Point/Bridge Image Step 4 Caution Step 5 Enter Y when the following CLI message displays: Proceed with reload? [confirm]. Interrupting the boot process will damage the configuration file. Wait until the access point/bridge Install Mode LED begins to blink green before continuing with CLI configuration changes. You can also see the following CLI message when the load process has finished: Line protocol on Interface Dot11Radio0, changed state to up.
Chapter 7 Troubleshooting Reloading the Access Point/Bridge Image Step 6 Click the System Software tab and then click Software Upgrade. The HTTP Upgrade page appears. Step 7 Click Browse to locate the image file on your PC. Step 8 Click Upload.
Chapter 7 Troubleshooting Reloading the Access Point/Bridge Image Obtaining the Access Point/Bridge Image File You can obtain the access point/bridge image file from the Cisco.com software center by following these steps: http://www.cisco.com/public/sw-center/sw-wireless.shtml Step 12 Click Option 2: Aironet Wireless Software Display Tables. Step 13 Find the access point firmware and utilities section and click Cisco Aironet 1300 Series (Cisco IOS Software).
Chapter 7 Troubleshooting Reloading the Access Point/Bridge Image Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide 7-14 OL-5048-02
A P P E N D I X A Translated Safety Warnings This appendix provides translations of the safety warnings that appear in this publication. These translated warnings apply to other documents in which they appear in English.
Appendix A Translated Safety Warnings Statement 84—Warning Definition Statement 84—Warning Definition Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. (To see translations of the warnings that appear in this publication, refer to the appendix “Translated Safety Warnings.
Appendix A Translated Safety Warnings Statement 245B—Explosive Device Proximity Warning Aviso ¡Advertencia! Varning! Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos fisicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes.
Appendix A Translated Safety Warnings Statement 346—RF Exposure Limits Aviso ¡Advertencia! Varning! Não opere o dispositivo de rede sem fios perto de cápsulas explosivas não protegidas ou num ambiente explosivo, a não ser que o dispositivo tenha sido modificado para se qualificar especialmente para essa utilização. No utilizar un aparato de la red sin cable cerca de un detonador que no esté protegido ni tampoco en un entorno explosivo a menos que el aparato haya sido modificado con ese fin.
Appendix A Translated Safety Warnings Statement 1001—Work During Lightning Activity ¡Advertencia! Para cumplir con los límites de exposición de radio frecuencia (RF)internacional, es preciso ubicar las antenas parabólicas a un mínimo de 22 cm (8,7 pulgadas) de las personas que se encuentren cerca y otras antenas, a un mínimo de 20 cm (7,9 pulgadas) de las personas que se encuentren cerca.
Appendix A Translated Safety Warnings Statement 1005—Circuit Breaker Aviso ¡Advertencia! Varning! Não trabalhe no sistema ou ligue e desligue cabos durante períodos de mau tempo (trovoada). No operar el sistema ni conectar o desconectar cables durante el transcurso de descargas eléctricas en la atmósfera. Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller koppla loss kablar.
Appendix A Translated Safety Warnings Statement 1022—Disconnect Device Aviso Este produto depende das instalações existentes para proteção contra curto-circuito (sobrecarga). Assegure-se de que o fusível ou disjuntor não seja superior a: 15A ¡Advertencia! Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes) del edificio.
Appendix A Translated Safety Warnings Statement 1022—Disconnect Device Aviso Advertencia Varning! Aviso Advarsel Deverá incorporar-se um dispositivo de desconexão de dois pólos de acesso fácil, na instalação eléctrica fixa. El cableado fijo debe incorporar un dispositivo de desconexión de dos polos y de acceso fácil. En lättillgänglig tvåpolig frånkopplingsenhet måste ingå i den fasta kopplingen. Um dispositivo de desconexão de dois pólos de fácil acesso deve ser incorporado à fiação fixa.
Appendix A Translated Safety Warnings Statement 1024—Ground Conductor Statement 1024—Ground Conductor Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024 Waarschuwing Deze apparatuur dient geaard te zijn.
Appendix A Translated Safety Warnings Statement 1030—Equipment Installation Statement 1030—Equipment Installation Warning Waarschuwing Varoitus Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door bevoegd geschoold personeel. Tämän laitteen saa asentaa, vaihtaa tai huoltaa ainoastaan koulutettu ja laitteen tunteva henkilökunta.
Appendix A Translated Safety Warnings Statement 1030—Equipment Installation ¡Advertencia! Varning! Aviso Advarsel Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo. Endast utbildad och kvalificerad personal bör få tillåtelse att installera, byta ut eller reparera denna utrustning. Somente uma equipe treinada e qualificada tem permissão para instalar, substituir ou dar manutenção a este equipamento.
Appendix A Translated Safety Warnings Statement 1033—SELV-IEC 60950 DC Power Supply Statement 1033—SELV-IEC 60950 DC Power Supply Warning Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards. Statement 1033 Waarschuwing Sluit de eenheid alleen maar aan op een gelijkstroombron die voldoet aan de veiligheidsvereisten voor extra-laag voltage (SELV) in de op IEC 60950 gebaseerde veiligheidsnormen.
Appendix A Translated Safety Warnings Statement 1040—Product Disposal Statement 1040—Product Disposal Warning Waarschuwing Varoitus Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen. Tämä tuote on hävitettävä kansallisten lakien ja määräysten mukaisesti.
Appendix A Translated Safety Warnings Statement 1040—Product Disposal Aviso Advarsel O descarte definitivo deste produto deve estar de acordo com todas as leis e regulamentações nacionais. Endelig bortskaffelse af dette produkt skal ske i henhold til gældende love og regler.
Appendix A Translated Safety Warnings Statement 1052—Installing and Grounding the Antenna Statement 1052—Installing and Grounding the Antenna Warning Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death.
Appendix A Translated Safety Warnings Statement 1052—Installing and Grounding the Antenna Advarsel Plasser ikke antennen nær de overliggende strømledningene eller andre lys- eller strømkretser, eller der den kan komme i kontakt med slike kretser. Ved installering av antennen må du være ytterst forsiktig slik at du ikke kommer i kontakt med slike kretser. Dette kan føre til alvorlig skade eller død.
Appendix A Translated Safety Warnings Statement 1052—Installing and Grounding the Antenna Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide OL-5048-02 A-17
Appendix A Translated Safety Warnings Statement 1052—Installing and Grounding the Antenna Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide A-18 OL-5048-02
A P P E N D I X B Declarations of Conformity and Regulatory Information This appendix provides declarations of conformity and regulatory information for the Cisco Aironet 1300 Series Access Point/Bridge.
Appendix B Manufacturers Federal Communication Commission Declaration of Conformity Statement Declarations of Conformity and Regulatory Information Manufacturers Federal Communication Commission Declaration of Conformity Statement Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Models: AIR-BR1310G-A-K9-R or AIR-BR1310G-A-K9 FCC Certification number: LDK102052P (AIR-MP21G-A-K9-B-P) or LDK102052 (AIR-MP21G-A-K9-B) Manufacturer: Cisco Systems, Inc.
Appendix B Declarations of Conformity and Regulatory Information Department of Communications—Canada Department of Communications—Canada Canadian Compliance Statement This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada. This device complies with Class B Limits of Industry Canada.
Appendix B Declarations of Conformity and Regulatory Information European Community, Switzerland, Norway, Iceland, and Liechtenstein Italiano: Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/EC. Nederlands: Deze apparatuur voldoet aan de belangrijkste eisen en andere voorzieningen van richtlijn 1999/5/EC. Norsk: Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-directiv 1999/5/EC.
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity for RF Exposure Declaration of Conformity for RF Exposure The radio module has been evaluated under FCC Bulletin OET 65C and found compliant to the requirements in CFR 47 Sections 2.1091, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices. The AIR-ANT3338 dish antenna should be installed more than 22 cm from your body or nearby persons.
Appendix B Declarations of Conformity and Regulatory Information Administrative Rules for Cisco Aironet Access Points and Bridges in Taiwan 3. If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact the number below. Contact Number: 03-5549-6500 Administrative Rules for Cisco Aironet Access Points and Bridges in Taiwan This section provides administrative rules for operating Cisco Aironet access points and bridges in Taiwan.
Appendix B Declarations of Conformity and Regulatory Information Administrative Rules for Cisco Aironet Access Points and Bridges in Taiwan Article 17 The operation of the low-power radio-frequency devices is subject to the conditions that no harmful interference is caused to aviation safety and authorized radio station; and if interference is caused, the user must stop operating the device immediately and can't re-operate it until the harmful interference is clear.
Appendix B Declarations of Conformity and Regulatory Information Administrative Rules for Cisco Aironet Access Points and Bridges in Taiwan Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide B-8 OL-5048-02
A P P E N D I X C Access Point/Bridge Specifications This appendix provides technical specifications for the access point/bridge, power injector, and power module. Table C-1 lists the technical specifications. Table C-1 Access Point/Bridge, Power Injector, and Power Module Specifications Category Access Point/Bridge Power Injector and Power Module Size Integrated antenna configuration: Power injector: 8.00 in. W x 8.10 in. H 2.62 in. D (20.32 cm W x 20.57 cm H 6.66 cm D) 4.62 in. W x 4.76 in.
Appendix C Table C-1 Access Point/Bridge Specifications Access Point/Bridge, Power Injector, and Power Module Specifications (continued) Category Access Point/Bridge Power Injector and Power Module Operational Vibration SAE J1455 Power injector: SAE J1455 Non-Operational Vibration SAE J1455 Power injector: Environmental Testing Compliance The enclosure has been successfully tested and is in — compliance with a NEMA 4 enclosure rating. Weight 2.5 lbs (1.13 kg) Power injector—0.8 lbs (0.
Appendix C Table C-1 Access Point/Bridge Specifications Access Point/Bridge, Power Injector, and Power Module Specifications (continued) Category Access Point/Bridge Power Injector and Power Module Data rates IEEE 802.11g-compliant radio: — 100, 50, 30, 20, 5, or 1 mW (at 1, 2, 5.
Appendix C Table C-1 Access Point/Bridge Specifications Access Point/Bridge, Power Injector, and Power Module Specifications (continued) Category Access Point/Bridge Power Injector and Power Module Electromagnetic Compatibility (EMC) Access Point/Bridge: Power injector and power module: Radio Type Approvals Access Point/Bridge radio: FCC Part 15.107 and 15.109 Class B ICES-003 Class B (Canada) EN 55022 Class B EN 55024 FCC Part 15.107 and 15.
Appendix C Access Point/Bridge Specifications Table C-3 Calculated Maximum Operating Range (in miles) for IEEE 802.11g Data Rates Data Rate (Mbps) Bridge Antenna Configuration Point-to-point configuration 13 dBi integrated antennas Point-to-point configuration 21 dBi dish antennas Point-to-multipoint configuration 5.
Appendix C Access Point/Bridge Specifications Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide C-6 OL-5048-02
A P P E N D I X D Channels and Antenna Settings This appendix lists the IEEE 802.11g (2.4-GHz) channels, maximum power levels, and antenna gains supported by the world’s regulatory domains.
Appendix D Channels and Antenna Settings Channels Channels IEEE 802.11g (2.4-GHz Band) The channel identifiers, channel center frequencies, and regulatory domains of each IEEE 802.11g 22-MHz-wide channel are shown in Table D-1. Table D-1 Note Channels for IEEE 802.
Appendix D Channels and Antenna Settings Maximum Power Levels and Antenna Gains Maximum Power Levels and Antenna Gains IEEE 802.11g (2.4-GHz Band) An improper combination of power level and antenna gain can result in equivalent isotropic radiated power (EIRP) above the amount allowed per regulatory domain. Table D-2 indicates the maximum power levels and antenna gains allowed for each IEEE 802.11g regulatory domain.
Appendix D Channels and Antenna Settings Maximum Power Levels and Antenna Gains Table D-2 Maximum Power Levels Per Antenna Gain for IEEE 802.11g (continued) Maximum Power Level (mW) Regulatory Domain Japan (-J) (10 mW/MHz EIRP maximum) Antenna Gain (dBi) CCK OFDM 5.2 (Omni) 10 10 9 (Patch) 10 10 10 (Yagi) 10 10 11 (Omni) 10 10 12 (Omni) 10 10 13 (Integrated patch) 10 10 13.5 (Yagi) 10 10 14 (Sector) 10 10 21 (Dish) 10 10 1.
Appendix D Channels and Antenna Settings Maximum Power Levels and Antenna Gains Step 9 On the OFDM Transmit Power (mW) setting, select the maximum OFDM power allowed for your antenna in your regulatory region. Step 10 Click Apply. Step 11 Close your browser. For additional configuration information, refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Bridges or to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points.
Appendix D Channels and Antenna Settings Maximum Power Levels and Antenna Gains Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide D-6 OL-5048-02
A P P E N D I X E Console Serial Cable Pinouts This appendix identifies the pinouts for the console serial cable that connects to the power injector’s console serial port.
Appendix E Console Serial Cable Pinouts Overview Overview The access point/bridge requires a special serial cable that connects the power injector’s console serial port (RJ-45 connector) to your PC’s COM port (DB-9 connector). This cable can be purchased from Cisco (part number AIR-CONCAB1200) or can be built using the pinouts in this appendix.
A P P E N D I X F Load-Dump Protection for Transportation Vehicles This appendix describes load-dump protection that is required for access point/bridge operation in some transportation vehicles. Load-Dump Protection The access point/bridge can be installed in vehicles such as automobiles, trucks, and buses. Electronic equipment in vehicle environments can be subjected to high-energy voltage transients where the vehicle battery is accidentally disconnected from the alternator charging circuit.
Appendix F Load-Dump Protection for Transportation Vehicles Load-Dump Protection Warning Caution Connect the unit only to a DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards. Statement 1033 To prevent damage to the access point/bridge or power injector, connect all coax cables from the power injector to the access point/bridge and connect the power jack to the power injector before applying power.
GLOSSARY Numeric 802.11 The IEEE standard that specifies carrier sense media access control and physical layer specifications for 1- and 2-megabit-per-second (Mbps) wireless LANs operating in the 2.4-GHz band. 802.11a The IEEE standard that specifies carrier sense media access control and physical layer specifications for wireless LANs operating in the 5-GHz frequency band. 802.11b The IEEE standard that specifies carrier sense media access control and physical layer specifications for 5.
Glossary broadcast packet A single data message (packet) sent to all addresses on the same subnet. A wireless LAN transceiver that is used to connect two or more wired Ethernet networks. bridge C CCK Complementary code keying. A modulation technique used by IEEE 802.11b-compliant wireless LANs for transmission at 5.5 and 11 Mbps. cell The area of radio range or coverage in which the wireless devices can communicate with the base station.
Glossary E EAP Extensible Authentication Protocol. An optional IEEE 802.1x security feature ideal for organizations with a large user base and access to an EAP-enabled Remote Authentication Dial-In User Service (RADIUS) server. Ethernet The most widely used wired local area network. Ethernet uses carrier sense multiple access (CSMA) to allow computers to share a network and operates at 10, 100, or 1000 Mbps, depending on the physical layer used.
Glossary multipath The echoes created as a radio signal bounces off of physical objects. multicast packet A single data message (packet) sent to multiple addresses. N non-root bridge A wireless transceiver connected to a remote Ethernet network that communicates only with another wireless transceiver connected to the main Ethernet network. O omni-directional This typically refers to a primarily circular antenna radiation pattern.
Glossary RP-TNC A connector type unique to Cisco Aironet radios and antennas. Part 15.203 of the FCC rules covering spread spectrum devices limits the types of antennas that may be used with transmission equipment. In compliance with this rule, Cisco Aironet, like all other wireless LAN providers, equips its radios and antennas with a unique connector to prevent attachment of non-approved antennas to radios. RSSI Receive signal strength indicator.
Glossary Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide GL-6 OL-5048-02
INDEX terminal emulator settings A 5-4 command-line interface, see CLI abbreviating commands antenna gains antennas 6-5 command modes D-3 commands C-3 Apply button audience 6-4 abbreviating 4-3 6-5 no and default ix connectors 6-5 1-4, C-1, C-3 conventions, document x B Back button D 4-3 basic settings, checking 7-6 data rates 2-6, C-3 declarations of conformity default commands C B-1 6-5 default configuration, resetting to defaults Cancel button caution documentation 4-3
Index F O FCC Declaration of Conformity FCC Safety Compliance OK button 2-3 filtering, show and more command output frequencies obtaining documentation B-2 6-10 xii 4-3 operating temperature C-1 D-2 frequency range C-2 P package contents G 2-6 pinouts, serial cable global configuration mode 6-4 H help, for the command line 6-5 E-2 power inline 1-3 input C-2 power level, maximum D-3 privileged EXEC mode 6-4 history changing the buffer size described 6-6 disabling 6-7 rec
Index T Telnet 5-14, 6-3 temperature, operating terminal emulator troubleshooting C-1 5-4 7-1 U unpacking 2-6 user EXEC mode 6-4 W warning, defined warnings x to xi, A-2 to A-3 2-2, A-1 Web-based interface, common buttons weight 4-3 C-2 Wi-Fi Protected Access (WPA) 5-12 Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide OL-5048-02 IN-3
Index Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide IN-4 OL-5048-02