C H A P T E R 4 Deploying the C65/76M This chapter describes how to deploy the Cisco 6500/7600 Series Manager, and consists of these sections: • Managing a Catalyst 6000 Family Switch or a Cisco 7600 Series Internet Router, page 4-1 • Deployment and Commissioning Process, page 4-6 Managing a Catalyst 6000 Family Switch or a Cisco 7600 Series Internet Router Managing a Catalyst 6000 family switch or a Cisco 7600 series Internet Router using CEMF is a two-step process: 1.
Chapter 4 Deploying the C65/76M Managing a Catalyst 6000 Family Switch or a Cisco 7600 Series Internet Router Deploying Objects The deployment process should be done after you install the C65/76M software for the first time, or after you install new hardware. Deployment informs the C65/ 76M of the presence of supported hardware. The C65/76M objects can be automatically discovered or manually deployed.
Chapter 4 Deploying the C65/76M Managing a Catalyst 6000 Family Switch or a Cisco 7600 Series Internet Router OSM Channelized SONET Modules Ethernet Interfaces OSM Channelized SONET Interfaces OSM Serial Sub-interfaces OSM PoS Sub-interfaces Content Switching Modules Software EtherChannels Syslog EIGRP BGP OSPF VTP VLAN STP IS-IS ACL NDE Loopback QoS QoS Policy Map The top-level Network Element object represents the entire switch including the physical and logical components of the switch.
Chapter 4 Deploying the C65/76M Managing a Catalyst 6000 Family Switch or a Cisco 7600 Series Internet Router Commissioning Objects Commissioning is the action required to notify CEMF to start actively monitoring the object.
Chapter 4 Deploying the C65/76M Managing a Catalyst 6000 Family Switch or a Cisco 7600 Series Internet Router Under the Network container, the Network Element objects are labelled by their IP addresses and added to the group representing the subnet that they belong to (192.168.12.0). Under the Physical container, the Network Element and Chassis objects are available. Note The Software objects are available only under the Catalyst6000Manager, Catalyst6500Manager, and Cisco7600Manager containment views.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Deployment and Commissioning Process There are three methods that can be used to enable CEMF to monitor a Catalyst 6000 family switch or a Cisco 7600 series Internet Router: • IP Auto Discovery This method should be used to deploy a large number of devices that are currently connected to the network.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process IP Auto Discovery The CEMF Auto Discovery application is used to search an existing network. The network is examined for IP and SNMP devices. An object is created for each new device discovered. The IP discovery window can be launched from either the Discovery icon from the CEMF Launchpad (Figure 3-2) or from the Deployment/ Auto Discovery... pop-up menu item on a selected object as shown in Figure 4-2.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-3 IP Discovery Window The contents of this window depend on how the window was launched. For example, if this window was launched from an object in the physical containment view, then the Physical Location parameter would be automatically set to the location from which the window was launched, as shown in Figure 4-3. For more information on the CEMF Auto Discovery process, refer to the “Auto Discovery” chapter of the CEMF 3.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Note When specifying the SNMP community string, use the read-write community string for the switch. If the read community string is used or appears first in the list of community strings, then that will be the SNMP community string used for both the read and read-write operations by the C65/76M. As a result, set operations will fail.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-4 Map Viewer with a Newly Discovered Catalyst 6500 Switch After the Network Element and Software objects have been created by the Auto Discovery process, their contents need to be determined. This determination is made by commissioning the Network Element object.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-5 Network Element Dialog Box When the dialog box is displayed, select the Configuration tab. In the CLI Passwords section, specify the Telnet Password and Enable Password parameters. The Telnet Password is the password used to connect to the switch using the Telnet protocol. The Enable Password is the password used to enter the enable mode on the switch or router.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-6 SNMP Tab in the Network Element Dialog Box Click the Commission button from the Configuration tab (Figure 4-5) to start the subchassis discovery process, which allows the C65/76M to determine which modules are installed on the switch or the router and also allows CEMF to start monitoring the switch or the router. Note Commissioning may take a few minutes.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-7 Fully IP-Discovered and Commissioned Catalyst 6513 Switch Manual Deployment The manual deployment method is used when discovery of the entire network is not needed and the specific IP address and type of device that is connected to the network is known.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Choose Deployment > Deploy Catalyst 6500 Manager from the pop-up menu. This pop-up menu item, shown in Figure 4-8, is available from the Site level in the Physical container and at the top level of the Catalyst6500Manager container.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process When you select this item, the Deployment Wizard window shown in Figure 4-9 is displayed. Figure 4-9 Deployment Wizard—Templates Property Description Catalyst 6500 Switch Network Element Only (Auto-discovered chassis) This option deploys the Network Element and Software objects. Used when you want to perform a subchassis discovery to automatically populate the Network Element object.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Choose the Catalyst 6500 Switch Network Element Only option and click the Forward button. The Object Parameters window, shown in Figure 4-10, is displayed. Tips The Catalyst 6500 Switch Network Element and Chassis option is used for the predeployment processes (see the “Predeployment” section).
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Property Description Number of Catalyst 6500 Switch elements The number of switches or routers that you want to deploy at the same time. Enter the number of Catalyst 6500 series switches or Cisco 7600 series Internet Routers that you want to deploy at the same time and click the Forward button. The remaining screens of this wizard are displayed for each switch or router to be deployed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Property Description Catalyst 6500 Switch Name Name of the Network Element object that is displayed in the Map Viewer application. IP Address IP address of the switch or router. SNMP V1 Read Community SNMP v1 read community used by the device. SNMP V1 Write Community SNMP v1 write community used by the device. SNMP V2c Read Community SNMP v2c read community used by the device.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Note The Network Element object can be deployed and commissioned without the IOS Telnet or enable passwords being set. However, some of the attributes will have the value of “ERROR” because those values are retrieved using IOS commands. Figure 4-12 Deployment Wizard—Views Property Description Physical Location in the Physical containment view where the new object will be deployed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process If the wizard was launched from a Site object in the Physical containment view, this screen will not be displayed, and the Physical parameter is set automatically. If this wizard is launched from any other containment view, this screen is displayed and you must specify the appropriate location in the Physical containment where the new object should be added.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-14 Deployment Wizard—Summary You can either cancel the operation by clicking Cancel or click Finish to create the object. If you click the Finish button, the Network Element and Software objects are added to the Map Viewer. The resulting Map Viewer resembles Figure 4-4. After the Network Element and Software objects are created by the Deployment Wizard, the type of switch and its contents need to be determined.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-15 Network Element Dialog Box Click the Commission button from the Configuration tab to start the subchassis discovery, which allows the C65/76M to determine which modules are installed on the switch or router, and also allows CEMF to start monitoring the switch or router. Note Commissioning may take a few minutes.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-16 Manually Deployed and Commissioned Catalyst 6506 Switch If an error is encountered when the object is commissioned, the Network Element object might go into the Mismatched or Lostcomms state and an alarm would be raised. The Network Element is placed in the Mismatched state if the IP address specified during the deployment wizard does not correspond to the device type that was deployed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Predeployment This deployment option is used to deploy the Catalyst 6000 family switch or Cisco 7600 series Internet Router into CEMF before it has been attached to the network. After an object has been predeployed, CEMF keeps the object in a decommissioned state until the device corresponding to the object is added to the network. After the switch is brought on-line, the predeployed object will be commissioned automatically.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-17 Manually Deploying a C65/76M Object When you choose the Deployment > Deploy Catalyst 6500 Manager option, the Deployment Wizard—Templates window, shown in Figure 4-18, is displayed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-18 Deployment Wizard—Templates Property Description Catalyst 6500 Switch Network Element Only (Auto-discovered chassis) This option deploys the Network Element and Software objects. Used when you want to perform a subchassis discovery to populate the Network Element object automatically. Catalyst 6500 Switch Network Element and Chassis This option deploys the Network Element, Chassis, and Software objects.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Choose the Catalyst 6500 Switch Network Element and Chassis option and click the Forward button. The Object Parameters window, shown in Figure 4-19, is displayed. Tips The Catalyst 6500 Switch Network Element Only option is used for the manual deployment process (see the “Manual Deployment” section).
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Property Description Number of Catalyst 6500 Switch elements The number of switches or routers that you want to predeploy at the same time. Enter the number of Catalyst 6500 series switches or Cisco 7600 series Internet Routers that you want to predeploy at the same time and click the Forward button. The detailed Object Parameters window, shown in Figure 4-20, is displayed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Property Description Catalyst 6500 Switch Name Name of the Network Element object that is displayed in the Map Viewer application. IP Address IP address that is given to the switch or router when it is connected to the network. SNMP V1 Read Community SNMP v1 read community used by the device. SNMP V1 Write Community SNMP v1 write community used by the device. SNMP V2c Read Community SNMP v2c read community used by the device.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-21 Deployment Wizard—Views Property Description Physical Location in the Physical containment view where the new object will be deployed. If this wizard was launched from a site in the Physical containment view, this screen will not be displayed. In this case, the Physical parameter is set automatically.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-22 Physical Location Selection Click the Apply button when the Physical containment has been selected. The Object Parameters window, shown in Figure 4-23, is displayed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-23 Deployment Wizard—Object Parameters Property Description Catalyst 6500 Chassis Name Label that is used for the Chassis object in the Map Viewer. Chassis Type This value specifies the type of chassis to deploy.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Note Note If you are deploying a Catalyst 6000 series switch, the following chassis types will be displayed in the Chassis Type drop down menu. Property Description Catalyst 6000 Chassis Name Label that is used for the Chassis object in the Map Viewer. Chassis Type This value specifies the type of chassis to deploy.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-24 Deployment Wizard—Summary You can either cancel the operation by clicking the Cancel button, or click the Finish button to create the object. If you click the Finish button, the Network Element, Chassis, and Software objects are added to the Map Viewer. The chassis image that is displayed will depend on the value used for the Chassis Type. Figure 4-25 shows an example of a predeployed Catalyst 6509 chassis.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-25 Predeployed Catalyst 6509 Chassis Object Cisco 6500/7600 Manager User Guide OL-2209-01 4-35
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Predeploying Subchassis Modules The next step in predeploying a Catalyst 6000 family switch or a Cisco 7600 series Internet Router in CEMF is to deploy the modules within the chassis.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-26 Predeploying Supervisor Modules The Supervisor Module Deployment Wizard—Object Parameters window, as shown in Figure 4-27, is displayed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-27 Supervisor Module Deployment Wizard—Object Parameters Property Description Number of Modules The number of supervisor modules to deploy. Enter the number of supervisor modules to predeploy and click the Forward button. The Supervisor Module Deployment Wizard—Object Parameters Details window is displayed for each module to deploy (see Figure 4-28).
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-28 Supervisor Module Deployment Wizard—Object Parameters Details Cisco 6500/7600 Manager User Guide OL-2209-01 4-39
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Property Description Module Name The name given to the Supervisor Module object. Module Type The type of supervisor module to be deployed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-29 Supervisor Module Deployment Wizard—Summary You can either click the Cancel button to cancel the operation, or click the Finish button to create the object. If the Chassis Slot Number corresponds to an occupied slot, an error message will be displayed. The error message resembles the message shown in Figure 4-30.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-30 Predeployment Failure Due to an Occupied Slot Ethernet Module To predeploy an Ethernet module (standard Ethernet, Fast Ethernet, or Gigabit Ethernet), choose the Deployment > Deploy Ethernet Module(s) option from the pop-up menu of the Chassis object (see Figure 4-31).
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-31 Predeploying Ethernet Modules Cisco 6500/7600 Manager User Guide OL-2209-01 4-43
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process After you choose the Deploy Ethernet Module option, the window shown in Figure 4-32 is displayed. Figure 4-32 Ethernet Module Deployment Wizard—Object Parameters Property Description Number of Modules The number of Ethernet modules to deploy. Enter the number of Ethernet module objects to be predeployed at the same time and click the Forward button. The window shown in Figure 4-33 is displayed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-33 Ethernet Module Deployment Wizard—Object Parameters Details Property Description Module Name The name given to the Ethernet Module object. Module Type The type of Ethernet card to be deployed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Property Description Module Type (continued) Chassis Slot Number • wsx6248atel—48-port 10/100TX with RJ-21 connectors and enhanced QoS • wsx6348rj45—48-port 10/100TX with RJ-45 connectors, enhanced QoS, and upgradeable voice card • wsx6348rj45v—48-port 10/100TX with RJ-45 connectors, enhanced QoS, and voice card • wsx6348rj21—48-port 10/100, RJ-21, upgradable to voice • wsx6524-100fxmm—Fabric-enabled 100FX Fast Ethernet Mod
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-34 Ethernet Module Deployment Wizard—Summary You can either click the Cancel button to cancel the operation or click the Finish button to create the object. If the Chassis Slot Number corresponds to an occupied slot, an error message is displayed. The error message resembles the message shown in Figure 4-30.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Switch Fabric Module To predeploy a Switch Fabric Module, choose the Deployment > Deploy Supervisor/Control Module(s) option in the pop-up menu from the Chassis object (see Figure 4-35).
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process After you choose the Deploy Switch Fabric Module(s) option, the Switch Fabric Module Deployment Wizard—Object Parameters window is displayed (see Figure 4-36). Figure 4-36 Switch Fabric Module Deployment Wizard—Object Parameters Property Description Number of Modules The number of Switch Fabric Modules to deploy at the same time.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Enter the number of Switch Fabric Modules to be deployed at the same time and click the Forward button. The Switch Fabric Module Deployment Wizard—Object Parameters Details window is displayed for each module to deploy (see Figure 4-37).
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Property Description Module Name The name given to the Switch Fabric Module object. Module Type The type of Switch Fabric Module to be deployed. This is a drop-down list with the following values: Chassis Slot Number • wsc6500sfm—Switch Fabric Module • wsc6500sfm2—Switch Fabric Module (for the Catalyst 6513 chassis) The slot in which the Switch Fabric Module is to be deployed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-38 Switch Fabric Module Deployment Wizard—Summary You can either click the Cancel button to cancel the operation or click the Finish button to create the object. If the Chassis Slot Number corresponds to an occupied slot, an error message is displayed. The error message resembles the message shown in Figure 4-30.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process FlexWAN Module To predeploy a FlexWAN Module, choose the Deployment > Deploy Supervisor/ Control Module(s) option in the pop-up menu from the Chassis object (see Figure 4-39). Figure 4-39 Predeploying FlexWAN Modules After you choose the Deploy FlexWAN Module(s) option, the FlexWAN Module Deployment Wizard—Object Parameters window is displayed (see Figure 4-40).
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-40 FlexWAN Module Deployment Wizard—Object Parameters Property Description Number of Modules The number of FlexWAN modules to be deployed at the same time. This value cannot be greater than 12. Enter the number of FlexWAN modules to be deployed at the same time and click Forward button. The FlexWAN Module Deployment Wizard – Object Parameters Details window is displayed for each module to be deployed (see Figure 4-41).
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-41 FlexWAN Module Deployment Wizard—Object Parameters Details Property Description Module Name The name given to the FlexWAN Module object. Module Type The type of FlexWAN Module to be deployed. This is a drop-down list with the following values: • Chassis Slot Number wsx61822pa—FlexWAN Module The slot in which the FlexWAN is to be deployed. The FlexWAN Modules can be deployed on slots 2 through 13.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Enter the details for the FlexWAN Module object and click the Forward button. The FlexWAN Module Deployment Wizard—Summary window is displayed (see Figure 4-42). Figure 4-42 FlexWAN Module Deployment Wizard—Summary You can either click the Cancel button to cancel the operation or click the Finish button to create the object. If the Chassis slot number corresponds to an occupied slot, an error message is displayed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Port Adapters To predeploy a port adapter, the FlexWAN module must first be deployed (see the “FlexWAN Module” section on page 4-53). Choose the Deployment > Deploy Port Adapter(s) option in the pop-up menu from the FlexWAN object (see Figure 4-43). Figure 4-43 Predeploying Port Adapters The Port Adapter Deployment Wizard—Object Parameters window is displayed (see Figure 4-44).
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-44 Port Adapter Deployment Wizard—Object Parameters Property Description Number of Modules The number of port adapters to be deployed at the same time. Enter the number of port adapters to be deployed at the same time and click Forward button. The Port Adapter Deployment Wizard – Object Parameters Details window is displayed for each module to be deployed (see Figure 4-45). Note This value cannot be greater than 2.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-45 Port Adapter Deployment Wizard—Object Parameters Details Cisco 6500/7600 Manager User Guide OL-2209-01 4-59
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Property Description Port Adapter Name The name given to the Port Adapter object. Port Adapter Type The type of port adapter to be deployed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Property Port Adapter Type (continued) FlexWAN Bay Number Note Description • pa-1t3-plus • pa-2t3-plus • pa-mct3 • pa-mc2t3 • pa-san-fc1 The FlexWAN bay in which the port adapter is to be deployed. The port adapter can be deployed in bays 0 and/or 1. Valid FlexWAN bay numbers are 0 or 1. If you enter any other number, an error message is displayed and the Forward button will not work.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-46 Port Adapter Deployment Wizard—Summary You can either click the Cancel button to cancel the operation or click the Finish button to create the object. If the Chassis slot number corresponds to an occupied slot, an error message is displayed. The message resembles the message shown in Figure 4-30.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Content Switching Module The Content Switching Module is a line card that provides server load balancing (SLB) of client traffic to server farms, firewalls, secure sockets layer (SSL) devices, or VPN termination devices. To predeploy a Content Switching Module (CSM), choose the Deployment > Deploy Supervisor/Control Module(s) option in the pop-up menu from the Chassis object (see Figure 4-47).
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-48 Deployment Wizard—Object Parameters Property Description Number of Modules The number of Content Switching Modules to be deployed at the same time. This value cannot be greater than 1 for IOS 12.1(8a)E3 and earlier, and no greater than 11 for IOS 12.1(8a)EX and later. Enter the number of Content Switching Modules to be deployed at the same time and click Forward button.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Note The C65/76M manager supports management and configuration of the CSM if only one CSM is deployed. If you choose to deploy more than one CSM in the chassis, inventory of the CSMs are supported, but the management and configuration of the CSMs are not supported.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-49 Deployment Wizard—Object Parameters Details Property Description Module Name The name given to the Content Switching Module object. Module Type The type of Content Switching Module to be deployed. This is a drop-down list with the following value: • Chassis Slot Number ws-x6066-slb-apc—Content Switching Module The slot in which the Content Switching Module is to be deployed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Enter the details for the Content Switching Module object and click the Forward button. The Deployment Wizard—Summary window is displayed (see Figure 4-50). Figure 4-50 Deployment Wizard—Summary You can either click the Cancel button to cancel the operation or click the Finish button to create the object. If the Chassis slot number corresponds to an occupied slot, an error message is displayed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Optical Services Module To predeploy an Optical Services Module (OSM), choose the Deploy Module(s), Deploy OSM Module option in the pop-up menu from the Chassis object (see Figure 4-51). Figure 4-51 Predeploying OSM Modules After you choose the Deploy OSM Module(s) option, the OSM Module Deployment Wizard—Object Parameters window is displayed (see Figure 4-52).
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-52 OSM Module Deployment Wizard—Object Parameters Property Description Number of Modules The number of OSMs to be deployed at the same time. Enter the number of OSMs to be deployed at the same time and click Forward button. The Deployment Wizard—Object Parameters Details window is displayed for each module to be deployed (see Figure 4-53).
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-53 OSM Module Deployment Wizard—Object Parameters Details Cisco 6500/7600 Manager User Guide 4-70 OL-2209-01
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Property Description Module Name The name given to the OSM object. Module Type The type of OSM to be deployed.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Property Module Type (continued) Description • osm-16oc3-pos-sl—16-port OC-3/STM-1 SONET/SDH OSM, SM-LR, with 4 ports of Gigabit Ethernet • osm-2oc12-pos-mm—2-port OC-12/STM-4 SONET/SDH OSM, MM, with 4 ports of Gigabit Ethernet • osm-2oc12-pos-si—2-port OC-12/STM-4 SONET/SDH OSM, SM-IR, with 4 ports of Gigabit Ethernet • osm-2oc12-pos-sl—2-port OC-12/STM-4 SONET/SDH OSM, SM-LR, with 4 ports of Gigabit Ethernet • osm-8oc3-pos-m
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Property Module Type (continued) Chassis Slot Number Description • osm-2choc48/t3-si—2-port channelized OC-48, SM-IR, with 4 ports of Gigabit Ethernet • osm-2choc48/t3-ss—2-port short reach OC48, with 4 ports of Gigabit Ethernet • osm-4choc12/t3-mm—4-port channelized OC-12, MM, with 4 ports of Gigabit Ethernet • osm-4choc12/t3-si—4-port channelized OC-12, SM-IR, with 4 ports of Gigabit Ethernet • osm-8choc12/t3-mm—8-port chann
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Figure 4-54 OSM Deployment Wizard—Summary You can either click the Cancel button to cancel the operation or click the Finish button to create the object. If the Chassis slot number corresponds to an occupied slot, an error message is displayed. The message resembles the message shown in Figure 4-30.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Commissioning Predeployed Objects A predeployed Network Element and subobjects are commissioned automatically when a coldStart SNMP trap that is issued from the switch or the router is received by the CEMF server. Note For the automatic commissioning to work, the switch or router must be configured to send SNMP traps and the CEMF server host must be in the trap client list.
Chapter 4 Deploying the C65/76M Deployment and Commissioning Process Cisco 6500/7600 Manager User Guide 4-76 OL-2209-01