Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
Preface This preface describes the objectives, audience, organization, and conventions of this guide, and describes related documents that have additional information.
Preface Organization This guide is organized into the following chapters and appendix. Product Overview Describes briefly the router models and the hardware features available. Installing the Router Lists items shipped with the router, equipment and tools necessary for installing the router, safety warnings and guidelines, and the procedures for installing the router.
Preface Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.
Preface Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.
Preface Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide OL-16193-01 vii
Preface Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
Preface Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide OL-16193-01 ix
Preface Warning When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO.
Preface Related Documentation In addition to the Cisco 860 series and Cisco 880 series ISR Hardware Installation Guide (this document), the Cisco 860 series and Cisco 880 series ISR documentation set includes the following documents: • Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers • Cisco 860 Series and Cisco 880 Series Integrated Services Routers Software Configuration Guide • Software Activation for Cisco Integrated Services Routers • Cisco Software Acti
Preface Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.
CH A P T E R 1 Product Overview This chapter provides an overview of the features available for the Cisco 860 series and Cisco 880 series integrated services routers (ISRs), and contains the following sections: • General Description, page 1-1 • Cisco 860 Series ISRs, page 1-2 • Cisco 880 Series ISRs, page 1-3 • Hardware Features, page 1-8 Note For compliance and safety information, see the Regulatory Compliance and Safety Information Roadmap that ships with the router and the Regulatory Complianc
Chapter 1 Product Overview Cisco 860 Series ISRs Cisco 860 Series ISRs The Cisco 860 series ISRs are fixed-configuration data routers that support the following features: • An integrated 4-port 10/100 Ethernet switch for connecting to the LAN • A10/100 Fast Ethernet (FE) port for connecting to the WAN • Optional, embedded-wireless access point Figure 1-1 shows the front panel details of the Cisco 860 wireless router.
Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-2 shows the back panel details of the Cisco 861 wireless (861W) ISR. Nonwireless routers do not have antennas or connectors on the back panel. However, the feature locations are similar for all Cisco 860 series routers.
Chapter 1 Product Overview Cisco 880 Series ISRs Cisco 880 Series Data Routers The Cisco 880 series data routers provide integrated VPN, wireless, 3G, and backup capabilities. Figure 1-3 and Figure 1-4 show the features available on Cisco 880 series data routers. Some of the features shown may not be available on your router. Figure 1-3 shows the front panel details of the Cisco 880 wireless data router. The USB port and the 3G card slot are located on the front panel.
Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-4 shows the back panel details of the Cisco 888W data router. Nonwireless routers do not have antennas or connectors on the back panel. However, the feature locations are similar across all Cisco 880 series data routers. Back Panel of the Cisco 888-W Data Router 231951 Figure 1-4 1 2 3 4 6 5 6 7 1 ISDN port—not available on 3G models 2 Primary WAN port—G.
Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-5 shows the front panel details of the Cisco 880 wireless voice router.
Chapter 1 Product Overview Cisco 880 Series ISRs Figure 1-6 shows the back panel details of the Cisco 880SRST-W voice router.
Chapter 1 Product Overview Hardware Features Figure 1-7 shows the back panel details of the Cisco 888SRST-W voice router. Back Panel of the Cisco C888SRST-W Voice Router 241905 Figure 1-7 2 1 2 6 3 4 5 7 8 9 10 1 Primary WAN port—G.
Chapter 1 Product Overview Hardware Features • Wireless LAN Connectivity • Feature Summary Kensington Lock A Kensington security slot is located on the router back panel. To secure the router to a desktop or other surface, use the Kensington lockdown equipment. Reset Button The Reset button resets the router configuration to the default configuration set by the factory.
Chapter 1 Product Overview Hardware Features Table 1-1 LED Descriptions for the Cisco 860 Series and Cisco 880 Series ISRs (continued) LED Color WLAN (2.4 GHz) Green Description 860 Series 2 On—Radio is connected, SSID is configured, signal is being Wireless models transmitted, and client is associated, but no data is being received or being transmitted. 880 Series Wireless models Slow blinking—Radio is connected, SSID is configured, and beacons are being transmitted.
Chapter 1 Product Overview Hardware Features Table 1-1 LED Descriptions for the Cisco 860 Series and Cisco 880 Series ISRs (continued) LED 3G RSSI 11 Color Description 860 Series 880 Series Green Off—Low signal strength (lower than -100 dBm). — 3G models On—High RSSI (-69 dBm or higher). Slow Blinking—Low or medium RSSI (-99 to -90 dBm). Fast Blinking—Medium RSSI (-89 to -70 dBm). 3G GSM 12 Amber On—No service. — 3G models Green On—Service is established.
Chapter 1 Product Overview Hardware Features Memory The Cisco 860 series and Cisco 880 series routers contain flash memory and main memory. Flash Memory The Cisco 860 series and Cisco 880 series ISRs use non-upgradable flash memory storage. Onboard flash memory contains the Cisco IOS software image, boot flash contains the ROMMON boot code, and quack contains the cookie configuration. The default flash memory for the Cisco 860 series and Cisco 880 series ISRs is 128 MB.
Chapter 1 Product Overview Hardware Features 3G Cellular Data WAN Connectivity The 3G (Evolution Data Only [EVDO], Universal Mobile Telecommunications Systems [UMTS]) cellular interface is intended for use as a backup data link, but it can also be used as a primary WAN data link. The 3G technology is third-generation wide-area cellular technology that is used in voice telephony and broadband wireless data in a mobile environment.
Chapter 1 Product Overview Hardware Features Table 1-3 Hardware Features Available in Cisco 860 Series and Cisco 880 Series ISRs (continued) Feature Description 860 Series 880 Series Console or AUX port Provides a connection to the terminal or PC for software configuration or troubleshooting. The console port may be configured as a virtual auxiliary port for dial backup and remote management. All models All models Security features Provides support for VPNs 4, Cisco IOS Firewall, and IPsec5.
Chapter 1 Product Overview Hardware Features Table 1-3 Hardware Features Available in Cisco 860 Series and Cisco 880 Series ISRs (continued) Feature 13 FXS /DID port Description 14 BRI voice port 860 Series 880 Series An FXS interface connects directly to a standard telephone, — a fax machine, or similar device. This interface supplies ringing voltage and dial tone to the station.
Chapter 1 Product Overview Hardware Features Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide 1-16 OL-16193-01
CH A P T E R 2 Installing the Router This chapter describes the equipment and the procedures for successfully installing the Cisco 860 series and Cisco 880 series integrated services routers (ISRs), and contains the following sections: Note • Equipment, Tools, and Connections, page 2-1 • Installing the Router, page 2-3 For compliance and safety information, see the Regulatory Compliance and Safety Information Roadmap that ships with the router and the Regulatory Compliance and Safety Information for
Chapter 2 Installing the Router Equipment, Tools, and Connections Table 2-1 Items and Their Quantities That Are Shipped with the Cisco 860 Series And Cisco 880 Series ISRs (continued) Item Power supply cable Cisco Configuration Professional (CCP) CD 4 Cisco 860 Series Routers Cisco 880 Series Routers 1 1 1 1 1. Cisco 861 and Cisco 881 ISRs only. 2. DSL = digital subscriber line. 3. Cisco 888 ISRs only. 4. Some SKUs do not include CCP.
Chapter 2 Installing the Router Installing the Router Installing the Router This section describes how to install the Cisco 860 series and Cisco 880 series ISRs. These routers can either be installed on a table top or other flat horizontal surface or be mounted on a wall. Warning This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect the host to earth ground during normal use. Statement 242 Warning This unit is intended to be mounted on a wall.
Chapter 2 Installing the Router Installing the Router Tip When choosing a location for wall-mounting the router, consider cable limitations and wall structure. To mount the router on the wall, follow these steps: Step 1 Anchor the screws into the wall, leaving 1/8 in. (0.32 cm) between the screw head and the wall. Figure 2-1 shows the wall-mount holes located on the underside of the router. Figure 2-1 Wall-mount Holes on the Underside of the Router 8.200 in. 3.673 in. 1 1 231987 5.961 in.
Chapter 2 Installing the Router Installing the Router Figure 2-2 Router Mounted on the Wall 1 1 4 231982 2 3 Step 3 1 Two number-10 wood screws mounted on the 3 wall 2 Wall-mount holes 4 Horizontal surface on which to place the power adapter Distance between the screw head and the wall, 1/8 in. (0.32 cm) Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the “Installing the Router Ground Connection” section on page 2-6.
Chapter 2 Installing the Router Installing the Router Installing the Router Ground Connection The router must be connected to a reliable earth ground. Install the ground wire in accordance with local electrical safety standards. • For NEC-compliant grounding, use size 14 AWG (2 mm2) or larger copper wire and a ring terminal with an inner diameter of 1/4 in. (5 to 7 mm). • For EN/IEC 60950–compliant grounding, use size 18 AWG (1 mm 2) or larger copper wire.
CH A P T E R 3 Connecting the Router This chapter describes how to connect Cisco 860 series and Cisco 880 series integrated services routers (ISRs) to Ethernet devices, Power over Ethernet (PoE), and the network.
Chapter 3 Connecting the Router Preparing to Connect the Router Preparing to Connect the Router Before you connect the router to the devices, install the router according to the instructions in Chapter 2, “Installing the Router.” Preventing Damage to the Router To prevent damage to your router, follow these guidelines when connecting devices to your router: • Caution Turn off power to the devices and to the router until all connections are completed.
Chapter 3 Connecting the Router Connecting a PC, Server, or Workstation Connecting a PC, Server, or Workstation To connect a PC (or other Ethernet devices) to an Ethernet switch port, follow these steps: Step 1 Connect one end of the yellow Ethernet cable to a Ethernet switch port on the router. Figure 3-1 shows a Cisco 888W router connected to a PC.
Chapter 3 Connecting the Router Connecting a Phone Connecting a Phone To connect a phone to an Ethernet switch port, follow these steps: Connect one end of the yellow Ethernet cable to Ethernet switch port 0 or port 1 on the router. Figure 3-2 shows a Cisco 888W router connected to a phone.
Chapter 3 Connecting the Router Connecting an External Ethernet Switch Connecting an External Ethernet Switch If more than four PCs in an office must be connected to each other, you can add Ethernet connections to the router by connecting an external Ethernet switch to the router’s Ethernet switch. To connect an external Ethernet switch to an Ethernet switch port on the router, perform the following steps: Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router.
Chapter 3 Connecting the Router Connecting a Terminal or PC to the Console Port Connecting a Terminal or PC to the Console Port Connect a terminal or PC to the Console Aux port either to configure the software by using the command-line interface (CLI) or to troubleshoot problems with the router. To connect a terminal or PC to the console port on the router and access the CLI, follow these steps: Connect the RJ-45 end of a DB-9–to–RJ-45 serial cable to the RJ-45 Console Aux port on the router.
Chapter 3 Connecting the Router Connecting a Data BRI Port • no flow control When the terminal emulator establishes communications, the router prompt is displayed. For more information on terminal emulation settings, see Applying Correct Terminal Emulator Settings for Console Connections.
Chapter 3 Connecting the Router Connecting a Data BRI Port Although the following procedure shows a Cisco 888W data router, this procedure applies to all Cisco 880 series router with a Data BRI port. To connect the Data BRI port to the ISDN service provider, follow these steps: Step 1 Connect one end of the orange ISDN S/T cable to the Data BRI port on the router. Figure 3-5 shows a Data BRI connection.
Chapter 3 Connecting the Router Connecting an FE Line—FE4 WAN Port Step 4 Connect the second unshielded Category 5 cable from the telecommunication service port on the splitter to the wall jack to allow a link to the network service provider. Connecting an FE Line—FE4 WAN Port To connect the Fast Ethernet (FE) 4 WAN port on the router, follow these steps: Step 1 Connect one end of the yellow cable to the Ethernet FE4 WAN port. Figure 3-6 shows an FE4 WAN port connection.
Chapter 3 Connecting the Router Connecting a G.SHDSL Line—G.SHDSL Port Note Follow the instructions from your Internet service provider to determine which modem port to use. Connecting a G.SHDSL Line—G.SHDSL Port To connect the router to a (global industry standard) symmetrical high-speed DSL (G.SHDSL) line, follow these steps: Step 1 Connect one end of the lavender DSL cable to the G.SHDSL port on the router. See Figure 3-7. Figure 3-7 Connecting the G.SHDSL Line 2 232175 1 1 Step 2 Note G.
Chapter 3 Connecting the Router Connecting Power over Ethernet Connecting Power over Ethernet Figure 3-8 shows how to connect the 48-VDC Power over Ethernet (PoE) power adapter in your Cisco 880 series ISR to an AC power outlet. The PoE provides power to port 0 and port 1 of the 4-port 10/100 FastEthernet switch. Note The router should also be connected to an AC power outlet through a 12-V adapter. To connect the router to an AC outlet, see “Connecting the AC Adapter” section on page 3-11.
Chapter 3 Connecting the Router Connecting the AC Adapter To connect your Cisco 860 series or Cisco 880 series ISR to an AC power outlet, follow these steps: Step 1 Connect the router to an AC power outlet as shown in Figure 3-9.
Chapter 3 Connecting the Router Connecting the AC Adapter Step 2 To secure the power cord to the router, attach the power lock clip to the power cord, slide the clip to the end of the DC plug. See Figure 3-10.
Chapter 3 Connecting the Router Connecting an FXS line Step 3 Snap the latches into the holes on either side of the power connector. See Figure 3-11. Figure 3-11 Power Lock Clip Latched Into the Holes on Either Side of the Power Connector 1 4 3 270800 2 1 Power lock clip 2 Power cord 3 Power adapter 4 AC plug Connecting an FXS line Use a standard straight-through RJ-11 modular telephone cable to connect an Foreign Exchange Service (FXS) port to a telephone or fax machine.
Chapter 3 Connecting the Router Connecting an FXS line To connect the FXS line, follow these steps: Step 1 Connect one end of the straight-through RJ-11 cable to the FXS port. Figure 3-12 shows an FXS line connection. Figure 3-12 Connecting an FXS Line 1 2 241907 3 Fax machine or telephone Step 2 1 FXS port 3 2 RJ-11 cable RJ-11 port Connect the other end of the cable to the RJ-11 port on the telephone or fax machine.
Chapter 3 Connecting the Router Connecting a FXO Line Connecting a FXO Line Use a straight-through RJ-11 cable to connect the Foreign Exchange Office (FXO) voice port to the PSTN or PBX through a telephone wall outlet. To connect the FXO line, follow these steps: Step 1 Connect one end of the straight-through RJ-11 cable to the FXO port. See Figure 3-13.
Chapter 3 Connecting the Router Connecting a Voice ISDN BRI Line Connecting a Voice ISDN BRI Line Use a straight-through RJ-45 cable to connect the Voice Basic Rate Interface (BRI) port to the ISDN network through a telephone wall outlet or other device. Caution To prevent damage to the router, be sure to connect the BRI cable to the BRI connector only, and not to any other RJ-45 connector.
Chapter 3 Connecting the Router Connecting a Voice ISDN BRI Line Figure 3-14 shows a Voice BRI line connection. Figure 3-14 Connecting a Voice BRI Line 1 2 241906 3 Step 2 1 Voice BRI port 2 RJ-45 cable 3 Wall jack Connect the other end of the cable to the RJ-45 wall outlet or other device.
Chapter 3 Connecting the Router Verifying Connections Verifying Connections To verify that all devices are properly connected to the router, first turn on all the connected devices. Then check the LEDs. To verify router operation, refer to Table 3-1 . For full LED description see Table 1-1 LED Descriptions for the Cisco 860 Series and Cisco 880 Series ISRs. Table 3-1 Verifying the Router Operation Power and Link LEDs to Check Normal Patterns Power OK On when power is supplied to router.
Chapter 3 Connecting the Router Verifying Connections Table 3-1 Verifying the Router Operation (continued) Power and Link PoE 14 LEDs to Check Normal Patterns PoE 0 Green when connected and powered. PoE 1 Amber when there is a fault with the inline power supply. 1. FE = Fast Ethernet. 2. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and G.SHDSL. 3. DSLAM = digital subscriber line access multiplexer. 4. 3G = Third-Generation. 5.
CH A P T E R 4 Initial Configuration This chapter provides instructions for initial configuration of the Cisco 860 series and Cisco 880 series Integrated Services Routers (ISRs). For initial configuration, we recommend using Cisco Configuration Professional (CP) Express. Cisco CP Express is a web-based graphical user interface that guides you through initial configuration.
Chapter 4 Initial Configuration Cisco IOS CLI To configure the initial router settings using Cisco IOS CLI, follow these steps: Step 1 Set up a console connection to your router. The following message is displayed: ... router con0 is now available Step 2 Press Return or Enter. The following message is displayed: Cisco Configuration Professional Express (Cisco CP Express) is installed on this device. This feature requires the one-time use of the username "cisco" with the password "cisco.
Chapter 4 Initial Configuration Setup Command Facility Step 6 Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-5. Setup Command Facility The setup command facility guides you through the configuration process by prompting you for the specific information that is needed to configure your system.
Chapter 4 Initial Configuration Setup Command Facility Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system Would you like to enter basic management setup? [yes/no]: yes Step 5 Enter a hostname for the router (this example uses Router): Configuring global parameters: Enter host name [Router]: Router Step 6 Enter an enable secret password.
Chapter 4 Initial Configuration Verifying the Initial Configuration snmp-server community public ! no ip routing ! interface FastEthernet0 no shutdown speed 100 duplex auto ip address 172.1.2.3 255.255.0.0 ! Step 12 Respond to the following prompts. Enter 2 to save the initial configuration. [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit.
Chapter 4 Initial Configuration Initial Configuration of the Wireless Access Point For information on how to do basic wireless configuration on your router see the Basic Wireless Device chapter of the Cisco 860 Series and Cisco 880 Series Integrated Services Routers Software Configuration Guide.
A P P E N D I X A Technical Specifications This appendix provides router, port, and cabling specifications for Cisco 860 series and Cisco 880 series Integrated Services Routers (ISRs). It contains the following sections: • Router Specifications, page A-1 • Wireless Access Point, page A-2 • LAN Port Pinouts, page A-3 • Console Port Connector Pinouts, page A-3 • G.
Appendix A Technical Specifications Wireless Access Point Table A-1 Router Specifications Description Design Specification Environmental Operating Ranges Nonoperating temperature –4 to 149°F (–20 to 65°C) Nonoperating humidity 5 to 95% relative humidity Nonoperating altitude 0 to 15,000 ft (4570 m) Operating temperature 32 to 104°F (0 to 40°C) Operating humidity 10 to 85% relative humidity Operating altitude 0 to 10,000 ft (3000 m) Noise criterion NC- 33; less than or equal to 32 dBA Ro
Appendix A Technical Specifications LAN Port Pinouts LAN Port Pinouts Table A-3 provides pinouts for the Ethernet LAN port. Table A-3 Ethernet LAN Port Pinouts Pin Function 1 RX+ 2 RX– 3 TX+ 4 Unused 5 Unused 6 TX– 7 Unused 8 Unused Console Port Connector Pinouts Table A-4 provides pinouts for the console connector (for connecting a terminal or PC).
Appendix A Technical Specifications Data BRI Port Connector Pinouts Table A-5 G.SHDSL WAN Port Pinouts Pin Function 3 TIP (Port0) 4 TIP (Port0) 5 TIP (Port1) 6 Unused Data BRI Port Connector Pinouts Table A-6 provides pinouts for the Data BRI port.
Appendix A Technical Specifications Cable Specifications Cable Specifications This section provides specifications for the following Ethernet cables: • Straight-through cable • Crossover cable Because of the autocrossover (autosensing) function, both straight-through and crossover cables can be used for the Ethernet LAN port. Ethernet Cable Specifications Table A-8 provides specifications that apply to both straight-through and crossover Ethernet cables.
Appendix A Technical Specifications Cable Specifications Cisco 860 Series and Cisco 880 Series Integrated Services Routers Hardware Installation Guide A-6 OL-16193-01