GETTING STARTED GUIDE Cisco Aironet 3600 Series Lightweight Access Points 1 About this Guide 2 Introduction to the Access Point 3 Safety Instructions 4 Unpacking 5 Configurations 6 Access Point Ports and Connectors 7 Configuring the Access Point 8 Mounting the Access Point 9 Deploying the Access Point on the Wireless Network 10 Installing Modules 11 Troubleshooting 12 Declarations of Conformity and Regulatory Information 13 Configuring DHCP Option 43 and DHCP Option 60 14 Access Point Spe
1 About this Guide This Guide provides instructions on how to install and configure your Cisco Aironet 3600 Series Access Point and how to install any port modules. This guide also provides mounting instructions and limited troubleshooting procedures. The 3600 Series Access Point is referred to as the access point in this document.
– Throughput, forwarding, and filtering performance scaled to meet 3 spatial stream 450 Mbps data-rates • 32 MB flash size • 802.11af/at – CDP (Cisco Discovery Protocol) • 2.4 GHz and 5 GHz 802.11n radios with the following features: – 4TX x 4RX – 3-spatial streams, 450 Mbps PHY rate – Spectrum intelligence – DPD (Digital Pre-Distortion) technology – Cisco Vector Beamforming—Implicit Co-phase beamforming for .
Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074 Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A. Statement 1005 Warning Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use.
4 Unpacking To unpack the access point, follow these steps: Step 1 Unpack and remove the access point and the accessory kit from the shipping box. Step 2 Return any packing material to the shipping container and save it for future use. Step 3 Verify that you have received the items listed below. If any item is missing or damaged, contact your Cisco representative or reseller for instructions.
• AIR-ANT2524DG-R • AIR-ANT2524V4C-R • AIR-ANT2544V4M-R • AIR-ANT2566P4W-R Internal Antennas The 3602I model access point is configured with four dual-band inverted-F antennas, and two 2.4-GHz/5-GHz dual-band radios. There are four antennas deployed inside the access point with one deployed on each corner of the 3602I access point top housing. Each antenna covers both the 2.4 GHz and the 5 GHz bands with a single feed line.
6 Access Point Ports and Connectors The 3602E model access point has external antenna connectors and the LED indictor on the top of the model, as shown in Figure 1. The 3602I model access point has integrated antennas and does not have external connectors on the top of the unit; however, it does have the LED indicator on top of the unit, as shown in Figure 2.
Figure 2 Access Point LED Indicator (top)—3602I Model 1 1 LED indicator The ports and connections on the bottom of the access point are shown in Figure 3.
1 Kensington lock slot 4 Console port 5 Security padlock and hasp (padlock not included) DC Power connection 2 3 Gbit Ethernet port 6 Mounting bracket pins (feet for desk or table-top mount) 7 Configuring the Access Point This section describes how to connect the access point to a wireless LAN controller. Because the configuration process takes place on the controller, see the Cisco Wireless LAN Controller Configuration Guide for additional information. This guide is available on Cisco.com.
Note You cannot edit or query any access point using the controller CLI if the name of the access point contains a space. Note Make sure that the controller is set to the current time. If the controller is set to a time that has already occurred, the access point might not join the controller because its certificate may not be valid for that time. Access points must be discovered by a controller before they can become an active part of the network.
• Access point mounting options: below a suspended ceiling, on a flat horizontal surface, or on a desktop. Note You can mount the access point above a suspended ceiling but you must purchase additional mounting hardware: See “Mounting the Access Point” section on page 15 for additional information.
Pre-Installation Configuration Setup The pre-installation configuration setup is shown in Figure 4. Figure 4 Pre-Installation Configuration Setup Controller Layer 3 devices 272488 Cisco Aironet access points To perform pre-installation configuration, perform the following steps: Step 1 Make sure that the Cisco wireless LAN controller DS port is connected to the network. Use the CLI, web-browser interface, or Cisco WCS procedures as described in the appropriate Cisco wireless LAN controller guide. a.
e. CAPWAP UDP ports must not be blocked in the network. f. The access point must be able to find the IP address of the controller. This can be accomplished using DHCP, DNS, or IP subnet broadcast. This guide describes the DHCP method to convey the controller IP address. For other methods, refer to the product documentation. See also the “Using DHCP Option 43” section on page 18 for more information. Step 2 Apply power to the access point: a. The access point is 802.3af (15.
c. If the access point shuts down, check the power source. d. After the access point finds the Cisco wireless LAN controller, it attempts to download the new operating system code if the access point code version differs from the Cisco wireless LAN controller code version. While this is happening, the Status LED blinks dark blue. e. If the operating system download is successful, the access point reboots. Step 3 Configure the access point if required.
8 Mounting the Access Point Cisco Aironet 3602 series access point can be mounted in several configurations, including on a suspended ceiling, on a hard ceiling or wall, on an electrical or network box, and above a suspended ceiling. Click this URL to browse to complete access point mounting instructions: http://www.cisco.com/en/US/docs/wireless/access_point/mounting/guide/apmount.
10 Installing Modules Modules are devices that are purchased as seperate items. When they are installed in the Cisco Aironet 3600 series access point, they give the access point additional capabilities. Modules connect to the access point’s module port. No special tools are required to install a module. Installing a Module Follow these steps to install a module: Step 1 Remove the module from the packaging. Step 2 Power down the access point.
Align the module’s connector with the connector on the back of the access point and click the module into place. Step 5 Screw down the thumb screws on the module. Note If the screws are not tightened, the module will not be recognized and may not operate correctly. Make sure not to over-tighten, only hand-tighten the screws. Step 6 Power up the access point. When the access point boots up, it will recognize the module.
11 Troubleshooting If you experience difficulty getting your access point installed and running, look for a solution to your problem in this guide or in additional access point documentation. These, and other documents, are available on Cisco.com.
Figure 5 Access Point LED Location 272378 1 1 Status LED The access point status LED indicates various conditions and are described in Table 1.
Table 1 LED Status Indications (continued) Message Type Status LED Message Meaning Operating status Blinking blue Software upgrade in progress Cycling through green, red, and off Discovery/join process in progress Rapidly cycling through blue, green, and red Access point location command invoked Blinking red Ethernet link not operational in FlexConnect mode Blinking blue Configuration recovery in progress (MODE button pushed for 2 to 3 seconds) Red Ethernet failure or image recovery (MODE b
Troubleshooting the Access Point Join Process Access points can fail to join a controller for many reasons: a RADIUS authorization is pending; self-signed certificates are not enabled on the controller; the access point’s and controller’s regulatory domains don’t match, and so on. Controller software enables you to configure the access points to send all CAPWAP-related errors to a syslog server.
• The access point is still connected to the same controller, and the global syslog server IP address configuration on the controller has been changed using the config ap syslog host global syslog_server_IP_address command. In this case, the controller sends the new global syslog server IP address to the access point.
Access Point Models Certification Number AIR-CAP3602E-A-K9 AIR-CAP3602I-A-K9 LDK102075 Module Models Certification Number AIR-RM3000AC-A-K9 LDK102086 Manufacturer: Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA This device complies with Part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device. Caution Within the 5.15 to 5.25 GHz and 5.47-5.725 GHz bands, this device is restricted to indoor operations to reduce any potential for harmful interference to co-channel Mobile Satellite System (MSS) operations.
Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English.
Statement 371—Power Cable and AC Adapter English Translation When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO.
Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada. This device complies with Class B Limits of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Cisco Aironet Access Points are certified to the requirements of RSS-210.
Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC 28
The following standards were applied: EMC—EN 301.489-1 v1.8.1; EN 301.489-17 v2.1.1 Health & Safety—EN60950-1: 2005; EN 50385: 2002 Radio—EN 300 328 v 1.7.1; EN 301.893 v 1.5.1 The conformity assessment procedure referred to in Article 10.4 and Annex III of Directive 1999/5/EC has been followed.
This device also conforms to the EMC requirements of the Medical Devices Directive 93/42/EEC. Note This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance. The product carries the CE Mark: Declaration of Conformity for RF Exposure This section contains information on compliance with guidelines related to RF exposure.
As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. Separation Distance MPE 0.63 mW/cm 2 Distance Limit 20 cm (7.87 inches) 1.
This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves The 3600 series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in Health Canada Safety Code 6. The guidelines include a substantial safety margin designed into the limit to ensure the safety of all persons, regardless of age and health.
• United Kingdom, National Radiological Protection Board at this URL: www.nrpb.org.uk • Cellular Telecommunications Association at this URL: www.wow-com.com • The Mobile Manufacturers Forum at this URL: www.mmfai.org Administrative Rules for Cisco Aironet Access Points in Taiwan This section provides administrative rules for operating Cisco Aironet access points in Taiwan. The rules for all access points are provided in both Chinese and English.
English Translation Administrative Rules for Low-power Radio-Frequency Devices Article 12 For those low-power radio-frequency devices that have already received a type-approval, companies, business units or users should not change its frequencies, increase its power or change its original features and functions.
English Translation Low-power Radio-frequency Devices Technical Specifications 4.7 Unlicensed National Information Infrastructure 4.7.5 Within the 5.25-5.35 GHz band, U-NII devices will be restricted to indoor operations to reduce any potential for harmful interference to co-channel MSS operations. 4.7.6 The U-NII devices shall accept any interference from legal communications and shall not interfere the legal communications.
Figure 6 Brazil Regulatory Information Module Models: AIR-RM3000AC-T-K9 Portuguese Translation Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. English Translation This equipment operates on a secondary basis and consequently must accept harmful interference, including interference from stations of the same kind.
13 Configuring DHCP Option 43 and DHCP Option 60 This section contains a DHCP Option 43 configuration example on a Windows 2003 Enterprise DHCP server for use with Cisco Aironet lightweight access points. For other DHCP server implementations, consult product documentation for configuring DHCP Option 43. In Option 43, you should use the IP address of the controller management interface. Note DHCP Option 43 is limited to one access point type per DHCP pool.
is the IP address of the default router, such as 10.0.0.1 is the IP address of the DNS server, such as 10.0.10.2 Step 3 Add the option 60 line using the following syntax: option 60 ascii “VCI string” For the VCI string, “Cisco AP c3602”. The quotation marks must be included.
Table 2 Access Point Specifications (continued) Category Specification Compliance The 3602 series access point complies with UL 2043 for products installed in a building’s environmental air handling spaces, such as above suspended ceilings. Safety UL 60950-1 CAN/CSA C22.2 No. 60950-1 IEC 60950-1 with all national deviations EN 60950-1 UL 2043 EMI and Susceptibility FCC Part 15.107 and 15.109 Class B ICES-003 Class B (Canada) EN 301.489 EN 55022 Class B EN 55024 VCCI Class B Radio FCC Part 15.
15 Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see What’s New in Cisco Product Documentation at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html. Subscribe to What’s New in Cisco Product Documentation, which lists all new and revised Cisco technical documentation, as an RSS feed and deliver content directly to your desktop using a reader application.