Cisco Model DPC3825 and EPC3825 8x4 DOCSIS 3.0 Wireless Residential Gateway User Guide In This Document IMPORTANT SAFETY INSTRUCTIONS ............................................................... 2 Introduction ............................................................................................................... 12 What's In the Carton? ...............................................................................................
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Notice to Installers The servicing instructions in this notice are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions, unless you are qualified to do so.
IMPORTANT SAFETY INSTRUCTIONS Mitteilung für CATV-Techniker Die in dieser Mitteilung aufgeführten Wartungsanweisungen sind ausschließlich für qualifiziertes Fachpersonal bestimmt. Um die Gefahr eines elektrischen Schlags zu reduzieren, sollten Sie keine Wartungsarbeiten durchführen, die nicht ausdrücklich in der Bedienungsanleitung aufgeführt sind, außer Sie sind zur Durchführung solcher Arbeiten qualifiziert.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
IMPORTANT SAFETY INSTRUCTIONS Protect the Product from Lightning In addition to disconnecting the AC power from the wall outlet, disconnect the signal inputs. Verify the Power Source from the On/Off Power Light When the on/off power light is not illuminated, the apparatus may still be connected to the power source. The light may go out when the apparatus is turned off, regardless of whether it is still plugged into an AC power source.
IMPORTANT SAFETY INSTRUCTIONS Check Product Safety Upon completion of any service or repairs to this product, the service technician must perform safety checks to determine that this product is in proper operating condition. Protect the Product When Moving It Always disconnect the power source when moving the apparatus or connecting or disconnecting cables.
IMPORTANT SAFETY INSTRUCTIONS United States FCC Compliance This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against such interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
IMPORTANT SAFETY INSTRUCTIONS Dynamic Frequency Selection (DFS) Dual Band Frequencies Some configurations of this product may operate in the 5150-5250MHz and 5470-5725MHz bands. If you select a channel in these frequency ranges, the product is restricted to indoor operation only per FCC guidance. The use of this product on the affected frequencies when outside is in non-compliance of the FCC regulations and guidelines.
IMPORTANT SAFETY INSTRUCTIONS CE Compliance Declaration of Conformity with Regard to the EU Directive 1999/5/EC (R&TTE Directive) This declaration is only valid for configurations (combinations of software, firmware and hardware) supported or provided by Cisco Systems for use within the EU. The use of software or firmware not supported or provided by Cisco Systems may result in the equipment no longer being compliant with the regulatory requirements.
IMPORTANT SAFETY INSTRUCTIONS Note: The full declaration of conformity for this product can be found in the Declarations of Conformity and Regulatory Information section of the appropriate product hardware installation guide, which is available on Cisco.com.
IMPORTANT SAFETY INSTRUCTIONS Latvia The outdoor usage of the 2.4 GHz band requires an authorization from the Electronic Communications Office. Please check http://www.esd.lv for more details. 2,4 GHz frekvenču joslas izmantošanai ārpus telpām nepieciešama atļauja no Elektronisko sakaru direkcijas. Vairāk informācijas: http://www.esd.lv. Note: The regulatory limits for maximum output power are specified in EIRP.
Introduction Introduction Welcome to the exciting world of high-speed Internet service. Your new Cisco® Model DPC3825 DOCSIS® 3.0 or EPC3825 EuroDOCSIS™ Wireless Residential Gateway is a cable modem that meets industry standards for high-speed data connectivity. The DPC3825 and EPC3825 residential gateway delivers data and wired (Ethernet) or wireless gateway capabilities to connect a variety of devices in the home or small office and support high-speed data access, all in one device.
Introduction Color-coded interface ports and corresponding cables simplify installation and setup DOCSIS-5 compliant LED labeling and behavior provides a user and technician friendly method to check operational status and act as a troubleshooting tool Allows automatic software upgrades by your service provider 4021196 Rev B 13
What's In the Carton? What's In the Carton? When you receive your wireless residential gateway, you should check the equipment and accessories to verify that each item is in the carton and that each item is undamaged.
Front Panel Description Front Panel Description The front panel of your residential gateway provides LED status indicators that indicate how well and at what state your residential gateway is operating. See Front Panel LED Status Indicator Functions (on page 96), for more information on front panel LED status indicator functions.
Back Panel Description Back Panel Description The following illustrations show the description and function of the back panel components on the Cisco DPC3825 residential gateway. 1 POWER—Connects the residential gateway to the AC power adapter that is provided with your residential gateway CAUTION: Avoid damage to your equipment. Only use the power supply that is provided with your residential gateway.
Back Panel Description 8 RESET—A momentary pressing (1-2 seconds) of this switch reboots the EMTA. Pressing the switch for more than ten seconds first causes a reset-to-factorydefault of all settings and then reboots the gateway CAUTION: The Reset button is for maintenance purposes only. Do not use unless instructed to do so by your cable service provider. Doing so may cause you to lose any cable modem settings you have selected.
What Are the System Requirements for Internet Service? What Are the System Requirements for Internet Service? To ensure that your residential gateway operates efficiently for high-speed Internet service, verify that all of the Internet devices on your system meet or exceed the following minimum hardware and software requirements. Note: You will also need an active cable input line and an Internet connection.
How Do I Subscribe to High-Speed Internet Service? How Do I Subscribe to High-Speed Internet Service? Before you can use your residential gateway, you need to have a high-speed Internet access account. If you do not have a high-speed Internet access account, you need to set up an account with your local service provider. Choose one of the options in this section.
Where Is the Best Location for My DOCSIS Residential Gateway? Where Is the Best Location for My DOCSIS Residential Gateway? The ideal location for your residential gateway is where it has access to outlets and other devices. Think about the layout of your home or office, and consult with your service provider to select the best location for your residential gateway. Read this user guide thoroughly before you decide where to place your residential gateway.
How Do I Mount the Modem on a Wall? (Optional) How Do I Mount the Modem on a Wall? (Optional) You can mount the residential gateway on a wall using two wall anchors, two screws, and the mounting slots located on the unit. The modem can be mounted vertically or horizontally. Before You Begin Before you begin, choose an appropriate mounting place. The wall can be made of cement, wood, or drywall.
How Do I Mount the Modem on a Wall? (Optional) Location and Dimensions of the Wall-Mounting Slots The following illustration shows the location and dimensions of the wall-mounting slots on the bottom of the modem. Use the information on this page as a guide for mounting your modem to the wall.
How Do I Mount the Modem on a Wall? (Optional) Mounting the Residential Gateway on a Wall 1 Using a drill with a 3/16-inch bit, drill two holes at the same height and 4 inches apart. Note: The preceding graphic illustrates the location of the mounting holes on the back of the residential gateway. 2 Are you mounting the residential gateway into a drywall or concrete surface where a wooden stud is available? If yes, go to step 3.
How Do I Connect My Gateway for Internet Service? How Do I Connect My Gateway for Internet Service? You can use your residential gateway to provide Internet access, and you can share that Internet connection with other Internet devices in your home or office. Sharing one connection among many devices is called networking. Connecting and Installing Internet Devices Professional installation may be available. Contact your local service provider for further assistance.
How Do I Connect My Gateway for Internet Service? 3 Connect the active RF coaxial cable from your service provider to the coax connector labeled CABLE on the back of the residential gateway. Note: To connect a TV, DHCT, set-top, or VCR from the same cable connection, you will need to install a cable signal splitter (not included). Always check with your service provider before using a splitter as a splitter may degrade the signal.
How Do I Configure My DOCSIS Residential Gateway? How Do I Configure My DOCSIS Residential Gateway? To configure your residential gateway, you must first access the WebWizard configuration pages. This section provides detailed instructions and procedures for accessing the WebWizard pages and for configuring your residential gateway to operate correctly. This section also presents examples and descriptions of each WebWizard configuration page.
How Do I Configure My DOCSIS Residential Gateway? 2 In the address field, enter the following IP address: 192.168.0.1. A Status DOCSIS WAN login page similar to the following page opens. 3 On the Status DOCSIS WAN page, leave the User Name and Password field blank and click Log In. The gateway opens with an Administration Management page in the forefront. You can use the Administration Management page to set your User Name and Password.
How Do I Configure My DOCSIS Residential Gateway? 4 On the Administration Management page, create a User Name and Password and then click Save Settings. Once you save the settings for your User Name and Password on the Administration Management page, the Setup Quick Setup page opens. Important: You have the option to leave the password field blank (factory default).
How Do I Configure My DOCSIS Residential Gateway? Configuring Quick Settings Use the descriptions and instructions in the following table to configure the network settings for the device. After you make your selections, click Save Settings to apply your changes or click Cancel Changes to cancel.
How Do I Configure My DOCSIS Residential Gateway? Section Field Description WLAN Wireless Network Allows you to enable or disable the wireless network. Select the desired option: Enable Disable Wireless Network Name (SSID) Allows you to enter a name for your wireless network or to use the default value. The value you enter he will be viewable on PCs and other wireless client devices such as the wireless network name.
How Do I Configure My DOCSIS Residential Gateway? Setup > Lan Setup The Setup Lan Setup page allows you to configure the settings for the Local Area Network (LAN) in your home. These settings include the range of IP addresses that define the LAN itself as well as how the addresses are assigned (automatically by DHCP or manually) as new devices are added to the network. Important: Unless you are knowledgeable about administering IP addresses, we recommend that you do not change these settings.
How Do I Configure My DOCSIS Residential Gateway? Section Field Description Network Address Server Settings (DHCP) DHCP Server Allows you to enable or disable the DHCP server in the residential gateway. The DHCP server is used to automatically allocate IP addresses to devices as they are attached to your home network. Connected Devices Summary page Click Connected Devices Summary in the Lan Setup page. The Connected Devices Summary page opens.
How Do I Configure My DOCSIS Residential Gateway? Section Field Description Maximum Number of DHCP Users Enter the maximum number of users to which the DHCP server can assign IP addresses for use in the LAN. This number cannot be greater than 254 minus the starting IP address described above. Client Lease Time The Client Lease Time is the amount of time an IP address is valid. IP address leases are renewed automatically by your PC and other devices that use DHCP to obtain IP addresses.
How Do I Configure My DOCSIS Residential Gateway? Section Field Description DDNS Service Disabling DDNS (Factory Default Settings) To disable DDNS, select Disabled from the drop-down list and click Save Settings. Enabling DDNS Note: In order to use the DDNS feature, you must first set up an account and establish a URL with www.DynDNS.org. The DDNS feature will not work without a valid account. To set up a DDNS account, open your browser and enter www.DynDNS.org in the address bar.
Configure Wireless Settings Configure Wireless Settings This section describes the options available from the Wireless pages that you can use to configure the parameters of the WAP to meet your specific requirements and needs. Wireless > Basic Settings Setting up your residential gateway for wireless communication provides you with the freedom to connect to the Internet from any location within range of the WAP without having to use wired connections.
Configure Wireless Settings Wireless Configuration Wi-Fi Protected Setup Example Wireless Configuration Wi-Fi Protected Setup Page Description Use the descriptions and instructions in the following table to configure the basic settings for Wi-Fi Protected Setup for the residential gateway. After you make your selections, click Save Settings to apply your changes or Cancel Changes to cancel.
Configure Wireless Settings Section Field Description WPS Setup Using Your Wi-Fi Adapter PIN (Option 2) This is the most secure option to register a wireless client with the gateway. You need the Wi-Fi Protected Setup PIN number, which is found in the client Wi-Fi Protected Setup utility. After entering the client's Wi-Fi Protected Setup PIN number, you can then connect to the gateway.
Configure Wireless Settings Section Field Description Basic Settings Wireless Network Enable or Disable the wireless network Wireless Configuration The default is WPS. See Wi-Fi Protected Setup (WPS) (on page 35) for more information about using WPS. Select Manual to manually set up your network using this option.
Configure Wireless Settings Section Field Description Wireless Network Name (SSID) The SSID is the name of your wireless network. The SSID is used by wireless technology to identify your network from other wireless networks in the area. The SSID can be up to 32 characters long. The factory default SSID is typically the last 6 characters of the CM MAC address found on the rating label located on the bottom of your gateway.
Configure Wireless Settings Wireless Security Page Description Use the following table to configure the wireless security for the residential gateway. After you make your selections, click Save Settings to apply your changes or Cancel Changes to cancel. Section Field Description Wireless Security Wireless Security Mode Choose one of these options for the security mode: WEP Wired Equivalent Privacy (WEP) security mode is defined in the original IEEE 802.11 standard.
Configure Wireless Settings Section Field Description WPA Security for Personal Networks – WPA or WPA2 Personal Modes Wi-Fi Protected Access (WPA) is a more secure wireless technology than WEP. WPA can be used for both Enterprise (corporate applications) and Personal (home network) wireless networks.
Configure Wireless Settings Section Field Description Security for Enterprise Networks - WPA-Enterprise Modes This option features WPA used in coordination with a RADIUS server for client authentication. (This should only be used when a RADIUS server is connected to the device.) Select from one of the following three WPA or WPA2 Enterprise modes: WPA-Enterprise WPA2-Enterprise WPA or WPA2-Enterprise Field Descriptions 42 Encryption. The default is TKIP+AES. RADIUS Server.
Configure Wireless Settings Wireless > MAC Filter The MAC Filter feature is used to either allow or block access to your wireless LAN based on the MAC Address of the wireless client devices. The MAC Filter feature, also known as an access list, can be used to help protect your wireless network from access by unauthorized users. Select the MAC Filter tab to open the Wireless MAC Filter page.
Configure Wireless Settings Section Field Description Access Restriction Access Restriction MAC Address Filter List Allows you to permit or block computers from accessing the wireless network. The choice that you make here affects the addresses listed on this page. Choose one of the following options: Block computers listed below from accessing the wireless network. Select this option to deny Internet access to the MAC addresses of the devices you list in the table.
Configure Wireless Settings Wireless Advanced Settings Page Description Use the descriptions and instructions in the following table to configure the advanced wireless settings for your residential gateway. After you make your selections, click Save Settings to apply your changes or Cancel Changes to cancel.
Configure Wireless Settings Section Advanced Wireless Field Description N Transmission Rate The rate of data transmission should be set depending on the speed of your Wireless-N networking. Select from a range of transmission speeds, or select Auto to have the device automatically use the fastest possible data rate and enable the Auto-Fallback feature. Auto-Fallback negotiates the best possible connection speed between the device and a wireless client. The factory default setting is Auto.
Configure Wireless Settings Section Field Description DTIM Interval The Delivery Traffic Indication Message (DTIM) indicates the interval between Broadcasts/Multicast transmissions. DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the device has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value.
Configure Wireless Settings Wireless > WDS Settings The Wireless Distribution System (WDS) Settings page allows you to expand the coverage of your wireless network by deploying signal repeaters. Make sure the channel settings are the same for all WDS enabled devices. Select the WDS Settings tab to open the Wireless WDS Settings page. Use this page to configure the WDS settings.
Configure Wireless Settings Wireless > QoS Quality of Service (QoS) ensures better service to high-priority types of network traffic, which may involve demanding, real-time applications, such as video conferencing. QoS settings allow you to specify priorities for different types of traffic. Lower priority traffic will be slowed down to allow greater throughput or less delay for high priority traffic. Select the QoS tab to open the Wireless QoS page.
Configure Wireless Settings Section Field Description No ACK Allows you to enable or disable NO ACK. This feature is recommended for data services where transmission is important and packet loss is tolerable to a certain degree. If you select Disable, an acknowledge packet is returned for every packet received. This provides a more reliable transmission, but it increases traffic load, which decreases performance.
Configure Security Configure Security Security > Firewall Advanced firewall technology deters hackers and protects the home network from unauthorized access. Use this page to configure a firewall that can filter out various types of unwanted traffic on the gateway’s local network. Select the Firewall tab to open the Security Firewall page. Use the descriptions and instructions in the following table to configure the firewall for your residential gateway.
Configure Security Section Field Description Filters Filter Proxy Enables/disables filter proxy. If local users have access to WAN proxy servers, they may be able to circumvent the content filters and access Internet sites blocked by the device. If you select the Filter Proxy feature, it will block access to any WAN proxy servers. Block Pop-Up Windows Enables/disables popup windows. Some commonly used applications employ popup windows as part of the application.
Configure Security Security > VPN Passthrough Use this page to configure Virtual Private Network (VPN) support. Enabling the settings on this page allows VPN tunnels using IPsec or PPTP protocols to pass through the gateway's firewall. Select the VPN Passthrough tab to open the Security VPN Passthrough page. Use the descriptions and instructions in the following table to configure the VPN passthrough for your residential gateway.
Configure Security Security > VPN A Virtual Private Network (VPN) is a connection between two endpoints in different networks that allows private data to be sent securely over public networks or other private networks. This is accomplished by creating a "VPN tunnel." A VPN tunnel connects the two PCs or networks and allows data to be transmitted over the Internet as if it were on a private network.
Configure Security Security VPN Tunnel Page Description Use the descriptions and instructions in the following table to configure the VPN tunnel for your gateway. After you make your selections, click Save Settings to apply your changes or Cancel Changes to cancel.
Configure Security Section Field Description Remote Secure Gateway Select the desired option, IP Addr., Any, or FQDN. If the remote gateway has a dynamic IP address, select Any or FQDN. If Any is selected, then the Gateway will accept requests from any IP address.
Configure Security Section Field Description Key Select one of the following options for the key exchange method: Management (continued) Auto (IKE) – Encryption: The Encryption method determines the length of the key used to encrypt/decrypt ESP packets. Notice that both sides must use the same method. – Authentication: The Authentication method authenticates the Encapsulating Security Payload (ESP) packets. Select MD5 or SHA. Notice that both sides (VPN endpoints) must use the same method.
Configure Security Section Field Description Status This field shows the connection status for the selected tunnel. The state is either Connected or Disconnected. Buttons Connect Click this button to establish a connection for the current VPN tunnel. If you have made any changes, click Save Settings to first apply your changes. Disconnect Click this button to break a connection for the current VPN tunnel. View Log Click this button to view the VPN log, which shows details of each established tunnel.
Configure Security View Log The Security VPN View Log page shows events captured by the firewall. The log displays the following items: Description of the event Number of events that have occurred Last occurrence of an event Target and source addresses You can view the following logs from this page: Access log Firewall log VPN log Parental Control log Click Clear to clear the log data.
Control Access to the Gateway Control Access to the Gateway Access Restrictions > IP Address Filtering Use the Access Restrictions IP Filtering page to configure IP address filters. These filters block a range of IP addresses from accessing the Internet. Note: If you are not familiar with the advanced settings detailed in this section, contact your service provider before you attempt to change any of the residential gateway default advanced IP filtering settings.
Control Access to the Gateway Select the MAC Address Filtering tab to open the Access Restrictions MAC Address Filtering page. The Block/Pass drop down menu allows you to block or pass Internet access to the MAC addresses of the devices you list in the MAC Address Filters table. The following table describes the function of the Block/Pass drop down menu. After you make your selections, click Save Settings to apply your changes or Cancel Changes to cancel.
Control Access to the Gateway Access Restrictions > Basic Rules Access restrictions allow you to block or allow specific kinds of Internet usage and traffic, such as Internet access, designated applications, websites, and inbound traffic during specific days and times. The Access Restrictions Basic Rules page allows you to configure parental controls on the residential gateway, and to monitor the individuals who are authorized to set parental controls.
Control Access to the Gateway Use the descriptions and instructions in the following table to configure the access restrictions basic rules for your residential gateway. After you make your selections, click Save Settings to apply your changes or Cancel Changes to cancel. Section Field Description Parental Control Basic Setup Parental Control Activation Allows you to enable or disable parental controls. To enable parental controls, select the Enable Parental Control check box and click Apply.
Control Access to the Gateway Section Field Description Override the Password Password Allows you to create a password to temporarily override user access restrictions to a blocked Internet site Re-Enter Password Re-enter the same password for confirmation of the override password in the previous field Access Duration Allows you to designate an amount of time in minutes that the Override password will allow temporary access to a restricted Internet site Apply Saves all additions, edits, and changes To us
Control Access to the Gateway Use the Keyword List to enter the keywords you wish to block. If any of these keywords appears in the URL of a website, access to the site will be blocked. Note that only the URL is check, not the content of each webpage. Access Restrictions > Time of Day Rules Use the Access Restrictions Time of Day Rules page to configure web access filters to block all Internet traffic to and from specific network devices based on day of week and time of day settings that you select.
Control Access to the Gateway Section Field Description Tod Filter Add Allows you to add a new Time of Day access filter or rule. Enter the name of the filter and click the Add key to add the filter to the list. Time of Day rules are used to restrict Internet access based on the day and time.
Control Access to the Gateway Access Restrictions User Setup Page Description Use the descriptions and instructions in the following table to configure the user setup for your residential gateway. After you make your selections, click Save Settings to apply your changes or Cancel Changes to cancel. Section Field Description User Add User Configure Allows you to add a new user profile. Enter the name of the user and click the Add User button to add the user to the list.
Control Access to the Gateway Section Field Description Inactivity Time 60 minutes [Factory default when a user is created. Otherwise, it is 0 (zero)]. Enter the amount of time during a user session where there is no Internet access activity, indicating that the user is no longer online. If the inactivity timer is triggered, the user session will be closed automatically. In order to regain Internet access, the user must log in again with their User Name and Password.
Configure Applications and Gaming Configure Applications and Gaming Overview Most well-known Internet applications are supported by Application Layer Gateways (ALGs). ALGs automatically adjust the gateway firewall to allow data to pass without making any custom settings. We recommend that you test your application before making changes in this section. Applications & Gaming > Port Filtering Use this window to configure transmission control protocol (TCP) and user datagram protocol (UDP) port filters.
Configure Applications and Gaming Section Field Description Port Filtering Start Port: This is the beginning of the port range. Enter the beginning of the range of port numbers (external ports) used by the server or Internet application. Check with the software documentation of the Internet application for more information if necessary. End Port: This is the end of the port range. Enter the end of the range of port numbers (external ports) used by the server or Internet application.
Configure Applications and Gaming Applications and Gaming Port Range Forward Page Description Use the descriptions and instructions in the following table to configure the port range forwarding for the residential gateway. Select enable for each. After you make your selections, click Save Settings to apply your changes or Cancel Changes to cancel. Section Field Description Port Range Forwarding Start For the Start port, select a port from the recommended 49152 65535 range.
Configure Applications and Gaming Applications & Gaming > Port Range Triggering Port range triggering is a way to dynamically forward ports to a LAN PC that needs them at a particular time. That particular time is when it runs a certain application that performs some event that trigger the router. This event must be an outbound access of a particular port range. Select the Port Range Triggering tab to open the Applications & Gaming Port Range Triggering page.
Configure Applications and Gaming Section Field Description End Port For the End port, select a port from the recommended 49152 65535 range. Keep in mind that ports used are program specific so check which ones the program requires to be forwarded. Protocol Select one of the following protocols: TCP UDP Both Enable Click the Enable checkbox to enable port range triggering for the relevant application.
Configure Applications and Gaming Applications and Gaming DMZ Page Description Use the descriptions and instructions in the following table to configure the port range triggering for the residential gateway. Select enable for each DMZ Host IP address. After you make your selections, click Save Settings to apply your changes or Cancel Changes to cancel.
Manage the Gateway Manage the Gateway Administration > Management The Administration Management page allows the network’s administrator to manage specific gateway functions for access and security. Select the Management tab to open the Administration Management page. Important: The following page displays when DHCP (factory default) is the Connection Mode. The page that displays when Static IP is selected is shown and described later in this section.
Manage the Gateway Field Description Gateway Setup (WAN) Connection Mode This setting allows you to determine how the WAN (or gateway interface to the Internet) obtains its IP address.
Manage the Gateway Field Description Internet IP Address Enter the gateway’s IP address (as seen from the Internet) Subnet Mask Enter the gateway’s subnet mask (as seen from the Internet, including your service provider) Default Gateway Enter the default gateway of the service provider’s server Primary DNS Enter the primary domain name server IP address(es) provided by your service provider. This is required.
Manage the Gateway Field Description Remote Access Remote Management Allows you to enable to disable remote management. This feature allows you to access and manage your gateway settings from the Internet when you are away from home. To allow remote access, select Enable. Otherwise, keep the default setting, as Disable. The protocol HTTP is required for remote management. To remotely access the device, enter https://xxx.xxx.xxx.
Manage the Gateway Administration > Reporting Administration reporting allows you to email various system activities to your email address. Select the Reporting tab to open the Administration Reporting page. Use the descriptions and instructions in the following table to configure the reporting feature on the gateway. After you make your selections, click Save Settings to apply your changes or Cancel Changes to cancel.
Manage the Gateway View Log To view the logs, complete the following steps. 1 Click View Log. A new window opens with the log data page. 2 To view a particular log, select one of the following options from the Type dropdown menu: All Access Log Firewall Log VPN Log 3 After the log data is displayed, use one of the following options: Click the Page Refresh button to update the log. Click the Clear button to clear all the information in the current log.
Manage the Gateway Administration > Diagnostics Administration diagnostics allow you to check the status of your Internet connection by using a Ping test. Select the Diagnostics tab to open the Administration Diagnostics page. Use the descriptions and instructions in the following table to configure the diagnostics feature on the gateway. After you make your selections, click Save Settings to apply your changes or Cancel Changes to cancel.
Manage the Gateway Administration > Backup & Restore Administration Backup & Restore allows you to back up you configuration of the Gateway and store it on your computer. You can use this file to restore a previously saved configuration for your Gateway. Select the Back Up & Restore tab to open the Administration Back Up & Restore page. CAUTION: Restoring a configuration file will destroy (overwrite) all of the existing settings.
Manage the Gateway Administration > Factory Defaults The Administration Factory Defaults page allows you to restore the configuration to its factory default settings. Select the Factory Defaults tab to open the Administration Factory Defaults page. CAUTION: If you restore the factory defaults, the gateway will lose all of the settings you have entered. Before you reset the gateway to its factory default settings, write down all of your custom settings.
Monitor Gateway Status Monitor Gateway Status This section describes the options available under the Status tab that you can use to monitor the status of the residential gateway and to perform diagnostics on the device and the network. Status > Gateway The Gateway Status page displays information about the gateway and its current settings. The on-screen information varies depending on the Internet Connection type you use. Select the Gateway tab to open the Status Gateway screen.
Monitor Gateway Status Section Field Description Internet Connection IP Address Displays the IP address of the WAN interface. This address is assigned to the gateway when it goes online. Subnet Mask Displays the subnet mask for your WAN port. This address is automatically assigned to your WAN port by your ISP except when a static IP address is set up. Default Gateway The IP address of the ISP's Default Gateway. DNS1-3 The DNS IP addresses currently used by the gateway.
Monitor Gateway Status Section Field Description IP Address Displays the IP address for the LAN subnet Subnet Mask Displays the subnet mask for your LAN DHCP Server Displays the status of your local DHCP server (Enabled or Disabled) Starting IP Address Displays the beginning of the range of IP addresses used by the DHCP server in your gateway End IP Address Displays the end of the range of IP addresses used by the DHCP server DHCP Client Table Click DHCP Client Table to show which devices are attached to
Monitor Gateway Status ARP/RARP Table Click ARP/RARP Table to see a complete list of all devices that are connected to your network. To retrieve the most up-to-date information, click Refresh. To exit this page and return to the Local Network page, click Close. The following illustration shows an example of the ARP/RARP Table. Status > Wireless The Wireless Network Status page displays basic information about the wireless network of the gateway. Select the Wireless tab to open the Status Wireless page.
Monitor Gateway Status Status Wireless Page Description Use the following table to review the status of your wireless network. Section Field Description Wireless Network MAC Address Displays the MAC Address of your gateway's local wireless access point Radio Band Displays one of the following radio band frequencies currently in operation: 2.4 GHz 5 GHz 2.4 and 5 GHz Note: Not all products support the 5 GHz radio band.
Monitor Gateway Status Status > DOCSIS WAN DOCSIS WAN Status displays information about the system of your cable modem. Select the DOCSIS WAN tab to open the Status DOCSIS WAN page. DOCSIS WAN Page Description Use the descriptions in the following table to review the status of your DOCSIS WAN network.
Monitor Gateway Status Section Field Description MAC Address (CM MAC Address) Displays the CM MAC Address. The CM MAC Address is a unique alphanumeric address for the cable modem coaxial interface, which is used to connect to the CMTS at the headend. A MAC address is a hardware address that uniquely identifies each node of a network.
Frequently Asked Questions Frequently Asked Questions Q. How Do I Configure TCP/IP Protocol? A. To configure TCP/IP protocol, you need to have an Ethernet Network Interface Card (NIC) with TCP/IP communications protocol installed on your system. TCP/IP is a communications protocol used to access the Internet. This section contains instructions for configuring TCP/IP on your Internet devices to operate with the residential gateway in Microsoft Windows or Macintosh environments.
Frequently Asked Questions 5 Select both Obtain an IP address automatically and Obtain DNS server address automatically in the Internet Protocol (TCP/IP) Properties window, and then click OK. 6 Click Yes to restart your computer when the Local Network window opens. The computer restarts. The TCP/IP protocol is now configured on your PC, and your Ethernet devices are ready for use. 7 Try to access the Internet. If you cannot access the Internet, contact your service provider for further assistance.
Frequently Asked Questions Renewing the IP Address on Windows 95, 98, 98SE, and ME Systems 1 Click Start, and then click Run to open the Run window. 2 Type winipcfg in the Open field, and click OK to execute the winipcfg command. The IP Configuration window opens. 3 Click the down arrow to the right of the top field, and select the Ethernet adapter that is installed on your PC. The IP Configuration window displays the Ethernet adapter information. 4 Click Release, and then click Renew.
Frequently Asked Questions Q. How does the residential gateway connect to my computer? A. The residential gateway connects to the PC using a wireless connection or the 10/100/1000BASE-T Ethernet port on your PC. If you want to use an Ethernet interface, Ethernet cards available from your local PC or office supply retailer, or from your service provider. For best performance over an Ethernet connection, your PC should be equipped with a Gigabit Ethernet card. Q.
Tips for Improved Performance Tips for Improved Performance Check and Correct If your residential gateway does not perform as expected, the following tips may help. If you need further assistance, contact your service provider. Verify that the plug to your residential gateway AC power is properly inserted into an electrical outlet. Verify that your residential gateway AC power cord is not plugged into an electrical outlet that is controlled by a wall switch.
Front Panel LED Status Indicator Functions Front Panel LED Status Indicator Functions Initial Power Up, Calibration, and Registration (AC Power applied) The following chart illustrates the sequence of steps and the corresponding appearance of the residential gateway front panel LED status indicators during power up, calibration, and registration on the network when AC power is applied to the residential gateway.
Front Panel LED Status Indicator Functions Front Panel LED Status Indicators During Initial Power Up, Calibration, and Registration High Speed Data Registration (continued) Step 7 Front Panel Indicator Data Network Registration Complete 1 POWER On 2 DS On 3 US On 4 ONLINE On 5 ETHERNET 1 - 4 On or Blinking 6 USB On or Blinking 7 WIRELESS LINK On or Blinking 8 WIRELESS SETUP Off 4021196 Rev B 97
Front Panel LED Status Indicator Functions Normal Operations (AC Power applied) The following chart illustrates the appearance of the residential gateway front panel LED status indicators during normal operations when AC power is applied to the gateway.
Front Panel LED Status Indicator Functions Special Conditions The following chart describes the appearance of the cable modem front panel LED status indicators during special conditions to show when you have been denied network access.
Notices Notices Trademarks Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. DOCSIS is a registered trademark of Cable Television Laboratories, Inc. EuroDOCSIS, EuroPacketCable, and PacketCable are trademarks of Cable Television Laboratories, Inc. The Wi-Fi Protected Setup mark is a mark of the Wi-Fi Alliance.
Notices Software and Firmware Use The software described in this document is protected by copyright law and furnished to you under a license agreement. You may only use or copy this software in accordance with the terms of your license agreement. The firmware in this equipment is protected by copyright law. You may only use the firmware in the equipment in which it is provided. Any reproduction or distribution of this firmware, or any portion of it, without our express written consent is prohibited.
For Information For Information If You Have Questions If you have technical questions, call Cisco Services for assistance. Follow the menu options to speak with a service engineer. Use the following table to find the center in your area.
For Information 4021196 Rev B 103
Cisco Systems, Inc. 5030 Sugarloaf Parkway, Box 465447 Lawrenceville, GA 30042 678.277.1000 www.cisco.com This document includes various trademarks of Cisco Systems, Inc. Please see the Notices section of this document for a list of the Cisco Systems, Inc., trademarks used in this document. Product and service availability are subject to change without notice. © 2010 Cisco and/or its affiliates. All rights reserved.