Cisco IE 3000 Switch Hardware Installation Guide June 2008 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
C O N T E N T S Preface ix Audience Purpose ix ix Conventions ix Related Publications x Obtaining Documentation, Obtaining Support, and Security Guidelines CHAPTER 1 Overview x 1-1 Overview 1-1 Switch Models 1-2 Front-Panel Description 1-2 10/100 Ports 1-5 Dual-Purpose Ports 1-5 100BASE-FX Ports 1-5 Power and Relay Connector 1-5 Console Port 1-6 LEDs 1-6 Setup LED 1-8 System LED 1-9 Alarm LED 1-9 Power Status LED 1-9 10/100 Port Status LEDs 1-10 100Base-FX Port Status LEDs 1-10 Dual-Purpos
Contents Installation Guidelines 2-3 Environment and Enclosure Guidelines: Other Guidelines 2-3 Verifying Package Contents 2-5 Adding Modules to the Switch 2-5 Expansion Module Configurations Connecting Modules 2-8 2-3 2-5 Installing or Removing the Compact Flash Memory Card 2-10 Verifying Switch Operation 2-11 Connecting a PC or a Terminal to the Console Port 2-12 Connecting the Protective Ground and DC Power 2-13 Grounding the Switch 2-13 Wiring the DC Power Source 2-16 Attach the Power and Relay Co
Contents Preparing the AC Power Cord 2-47 Connecting the AC Power Cord to the Power Converter 2-48 Connecting the Power Converter to a DC Power Source 2-51 Applying Power to the Power Converter 2-53 Where to Go Next CHAPTER 3 Troubleshooting 2-53 3-1 Diagnosing Problems 3-1 Verify Switch POST Results 3-1 Verify Switch LEDs 3-2 Verify Switch Connections 3-2 Bad or Damaged Cable 3-2 Ethernet and Fiber Cables 3-2 Link Status 3-3 Transceiver Issues 3-3 Port and Interface Settings 3-3 Ping End Device 3-3
Contents Expansion Module Configurations Connecting Modules B-11 B-9 Installing or Removing the Compact Flash Memory Card B-13 Verifying Switch Operation B-14 Connecting a PC or a Terminal to the Console Port B-15 Connecting the Protective Ground and DC Power B-16 Grounding the Switch B-17 Wiring the DC Power Source B-19 Attach the Power and Relay Connector to the Switch Running POST B-25 Power On the Switch B-25 Verify POST Results B-25 Disconnect Power B-25 Installing the Switch B-26 Installing the S
Contents Where to Go Next APPENDIX C Cable and Connectors B-59 C-1 Connector Specifications C-1 10/100 Ports C-1 Connecting to 10BASE-T- and 100BASE-TX-Compatible Devices Connecting to 1000BASE-T Devices C-1 100BASE-FX Ports C-3 SFP Module Ports C-3 Dual-Purpose Ports C-4 Console Port C-4 Cable and Adapter Specifications C-4 SFP Module Cable Specifications C-4 Two Twisted-Pair Cable Pinouts C-5 Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports Crossover Cable and Adapter Pinouts C-7 Identifying a
Contents Cisco IE 3000 Switch Hardware Installation Guide viii OL-13017-01
Preface Audience This guide is for the networking or computer technician responsible for installing Cisco IE 3000 series switches. We assume that you are familiar with the concepts and terminology of Ethernet and local area networking. Purpose This guide documents the hardware features of the Cisco IE 3000 switches. It describes the physical and performance characteristics of each switch, explains how to install a switch, and provides troubleshooting information.
Preface Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.
CH A P T E R 1 Overview This chapter provides these topics that describe the Cisco Industrial Ethernet (IE) 3000 switch, hereafter referred to as the switch.
Chapter 1 Overview Switch Models Switch Models Table 1-1 describes the switch and the expansion modules. The Cisco IE-3000-4TC and the Cisco IE-3000-8TC are the switch models, and the Cisco IEM-3000-8TM and the Cisco IEM-3000-8FM are expansion modules that you can connect to increase the number of ports. For instructions on how to connect the expansion modules to the switch, see the “Adding Modules to the Switch” section on page 2-5. .
Chapter 1 Overview Front-Panel Description Figure 1-1 Cisco IE-3000-8TC Switch 1 201699 2 3 4 5 1 Power and relay connectors 4 10/100 ports 2 Console port 5 Protective ground connection 3 Dual-purpose ports Figure 1-2 Cisco IE-3000-4TC Switch 1 201700 2 3 4 5 1 Power and relay connectors 4 10/100 ports 2 Console port 5 Protective ground connection 3 Dual-purpose ports Cisco IE 3000 Switch Hardware Installation Guide OL-13017-01 1-3
Chapter 1 Overview Front-Panel Description Cisco IEM-3000-8TM Module 201702 Figure 1-3 1 1 10/100 ports Cisco IEM-3000-8FM Module 201701 Figure 1-4 1 1 100BASE-FX ports Cisco IE 3000 Switch Hardware Installation Guide 1-4 OL-13017-01
Chapter 1 Overview Front-Panel Description 10/100 Ports You can set the 10/100 ports to operate at 10 or 100 Mb/s in full-duplex or half-duplex mode. You can also set these ports for speed and duplex autonegotiation in compliance with IEEE 802.3AB. (The default setting is autonegotiate.) When set for autonegotiation, the port senses the speed and duplex settings of the attached device and advertises its own capabilities.
Chapter 1 Overview Front-Panel Description The switch accessory pack includes the mating power and relay connectors. These connectors provide screw terminals for terminating the DC power and alarm wire and the connector plugs into the power and relay receptacles on the front panel. The positive DC power connection is labeled V, and the return connection is labeled RT (see Figure 1-5).
Chapter 1 Overview Front-Panel Description Figure 1-6 LEDs on the Cisco IE 3000 Switch 1 2 3 6 5 7 201703 4 8 1 Express setup button 5 Dual-purpose uplink port LED 2 System LED 6 Pwr B LED 3 Alarm LED 7 Pwr A LED 4 Setup LED 8 Port LED LEDs on the Cisco IEM-3000-8TM Module 201706 Figure 1-7 1 1 10/100 port LED Cisco IE 3000 Switch Hardware Installation Guide OL-13017-01 1-7
Chapter 1 Overview Front-Panel Description LEDs on the Cisco IEM-3000-8FM Module 201705 Figure 1-8 1 1 100BASE -FX port LEDs Setup LED The Setup LED displays the express setup mode for the initial configuration. Table 1-2 lists the LED colors and their meanings. Table 1-2 Setup LED Color Setup Status Off (dark) Switch is configured as a managed switch. Solid green Switch is in initial setup. Blinking green Switch is in initial setup, in recovery, or initial setup is incomplete.
Chapter 1 Overview Front-Panel Description System LED The System LED shows whether the system is receiving power and is functioning properly. Table 1-3 lists the system LED colors and their meanings. Table 1-3 System LED Color System Status Off System is not powered on. Green System is operating normally. Red Switch is not functioning properly. Alarm LED Table 1-4 lists the alarm LED colors and their meanings.
Chapter 1 Overview Front-Panel Description Note The Pwr A and Pwr B LEDs show that power is not present on the switch if the power input drops below the low valid level. The power status LEDs only show that power is present if the voltage at the switch input exceeds the valid level. The difference, or hysteresis, ensures that the power status LEDs do not oscillate at values near 18 V.
Chapter 1 Overview Compact Flash Memory Card Dual-Purpose Port LEDs Figure 1-9 shows the LEDs on a dual-purpose port. You can configure each port as either a 10/100/1000 port through the RJ-45 connector or as an SFP module, but not both at the same time. The LEDs show how the port is being used (Ethernet or SFP module). The LED colors have the same meanings as described in Table 1-6.
Chapter 1 Overview Rear-Panel Description Compact Flash Memory Card Slot 201832 Figure 1-10 1 Note Bottom of switch You can obtain replacement flash memory cards (CF-IE3000=) by calling Cisco Technical Support. Rear-Panel Description The rear panel of the switch, modules, and power converter have latches for installation on either a DIN rail or a wall. See Figure 1-11. The latches slide outward to position the switch over a DIN rail and slide inward to secure the switch to a DIN rail.
Chapter 1 Overview Power Converter (Optional) Figure 1-11 1 201697 2 Cisco IE 3000 Switch Rear Panel 1 DIN rail latch 2 Foot in recessed position Power Converter (Optional) The switch can be used with an optional AC/DC power converter. The power converter (PWR-IE3000-AC) can supply 24-VDC power to one switch and up to two modules. The power converter is mounted on the side of a switch and provides power to the switch through a preassembled power cable.
Chapter 1 Overview Management Options Figure 1-12 displays the power converter. Figure 1-12 Cisco IE 3000 Switch AC/DC Power Converter 1 2 202314 3 1 DC output connector 2 Status LED 3 AC/DC input power connector Management Options The switch supports these management options: • Cisco Network Assistant Cisco Network Assistant is a PC-based network management GUI application optimized for LANs of small and medium-sized businesses.
Chapter 1 Overview Network Configurations • CiscoWorks application The CiscoWorks device-management application displays the switch image that you can use to set configuration parameters and to view the switch status and performance information. The CiscoView application, which you purchase separately, can be a standalone application or part of a Simple Network Management Protocol (SNMP) platform. See the CiscoView documentation for more information.
Chapter 1 Overview Network Configurations Cisco IE 3000 Switch Hardware Installation Guide 1-16 OL-13017-01
CH A P T E R 2 Switch Installation This chapter describes how to install your switch, interpret the power-on self-test (POST), and connect the switch to other devices. Caution If your installation is in a hazardous environment, see Appendix B, “Installation In a Hazardous Environment” for instructions.
Chapter 2 Switch Installation Preparing for Installation Warnings These warnings are translated into several languages in the Regulatory Compliance and Safety Information Guide. Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.
Chapter 2 Switch Installation Preparing for Installation Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of: 140°F (60°C) Statement 1047 Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074 Warning To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 4.13 in. (105 mm).
Chapter 2 Switch Installation Preparing for Installation • Personnel responsible for the application of safety-related programmable electronic systems (PES) shall be aware of the safety requirements in the application of the system and shall be trained in using the system. • This product is grounded through the DIN rail to chassis ground. Use zinc-plated yellow-chromate steel DIN rail to assure proper grounding.
Chapter 2 Switch Installation Adding Modules to the Switch Verifying Package Contents Carefully remove the contents from the shipping container, and check each item for damage. If any item is missing or damaged, contact your Cisco representative or reseller for support. Return all packing materials to the shipping container and save them.
Chapter 2 Switch Installation Adding Modules to the Switch Table 2-1 lists the port combinations using switch and expansion modules.
Chapter 2 Switch Installation Adding Modules to the Switch Figure 2-1 Sample Combinations of Expansion Modules 1 2 3 201827 4 Cisco IE 3000 Switch Hardware Installation Guide OL-13017-01 2-7
Chapter 2 Switch Installation Adding Modules to the Switch 1 Cisco IE-3000-4TC switch with Cisco IEM-3000-8TM and Cisco IEM-3000-8FM expansion modules (12 FE and 8 FX ports) 2 Cisco IE-3000-4TC switch with one Cisco IEM-3000-8FM expansion module (4 FE and 8 FX ports) 3 Cisco IE-3000-4TC switch with one Cisco IEM-3000-8TM expansion modules (12 FE ports) 4 Cisco IE-3000-4TC switch with two Cisco IEM-3000-8TM expansion modules (20 FE ports) Connecting Modules Follow these directions to connect the e
Chapter 2 Switch Installation Adding Modules to the Switch Step 3 Push up the upper module latches (at the top of the switch and the module). See Figure 2-4. Push down the lower module latches (at the bottom of the switch and the module). Pushing the Module Latches Up 201824 Figure 2-4 Step 4 Align the connectors on the switch and the module, and slide the switch and the module together to make the connection. See Figure 2-5.
Chapter 2 Switch Installation Installing or Removing the Compact Flash Memory Card Pushing the Module Latches In 201826 Figure 2-6 Step 6 (Optional) if the first module attached was an Cisco IEM-3000-8TM, you can connect another Cisco IEM-3000-8TM or Cisco IEM-3000-8FM expansion module. Follow Step 1 to Step 5 to connect the module. Installing or Removing the Compact Flash Memory Card The switches store Cisco IOS software images and switch configurations on a removable flash memory card.
Chapter 2 Switch Installation Verifying Switch Operation Follow these directions to remove or replace the compact flash memory card: Step 1 Locate the compact flash memory card slot on the bottom of the switch. See Figure 2-7. Removing the Compact Flash Memory Card from the Switch 201851 Figure 2-7 1 Step 2 Bottom of switch Install or remove the card, as desired: • To remove the card, grasp the card top, and pull it out. Place it in an antistatic bag to protect it from static discharge.
Chapter 2 Switch Installation Verifying Switch Operation Connecting a PC or a Terminal to the Console Port To connect a PC to the console port, use the supplied RJ-45-to-DB-9 adapter cable. To connect a terminal to the console port, you need to provide an RJ-45-to-DB-25 female DTE adapter. You can order a kit (part number ACS-DSBUASYN=) with that adapter from Cisco. For console-port and adapter-pinout information, see the “Cable and Adapter Specifications” section on page C-4.
Chapter 2 Switch Installation Verifying Switch Operation Step 5 Connect the other end of the adapter cable to the PC or terminal adapter. Step 6 Start the terminal-emulation software on the PC.
Chapter 2 Switch Installation Verifying Switch Operation Warning Caution Note This equipment is intended to be grounded to comply with emission and immunity requirements. Ensure that the switch functional ground lug is connected to earth ground during normal use.
Chapter 2 Switch Installation Verifying Switch Operation Crimping the Ring Terminal 76666 Figure 2-10 Step 4 Slide the ground screw through the ring terminal. Step 5 Insert the ground screw into the functional ground screw opening on the front panel. Step 6 Use a ratcheting torque screwdriver to tighten the ground screw and ring terminal lug to the switch front panel to 8.5 in-lb. The torque should not exceed 8.5 in-lb. See Figure 2-11.
Chapter 2 Switch Installation Verifying Switch Operation Wiring the DC Power Source Read these warnings before wiring the DC power source: Caution This product is intended to be supplied by a Listed Class 2 power source marked with "Class 2" and rated from 18 to 60 VDC, 2.1 A. Warning A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Statement 1022 Warning This product relies on the building’s installation for short-circuit (overcurrent) protection.
Chapter 2 Switch Installation Verifying Switch Operation To wire the switch to a DC-input power source, follow these steps: Step 1 Locate the power and relay connector (see Figure 2-12). Figure 2-12 Power and Relay Connector 201815 V RT A A Step 2 Identify the positive and return DC power connections on the connector. The positive DC power connection is labeled V, and the return is the adjacent connection labeled RT. See Figure 2-12.
Chapter 2 Switch Installation Verifying Switch Operation Figure 2-14 Inserting Wires in the Power and Relay Connector 1 2 202028 V RT A A 1 Step 6 Caution Power source positive connection 2 Power source return connection Use a ratcheting torque flathead screwdriver to torque the power and relay connector captive screws (above the installed wire leads) to 2 in-lb. See Figure 2-15. Do not over-torque the power and relay connector captive screws. The torque should not exceed 2 in-lb.
Chapter 2 Switch Installation Verifying Switch Operation Figure 2-15 Torquing the Power and Relay Connector Captive Screws 1 201817 V RT A A 1 Step 7 Power and relay connector captive screws Connect the other end of the positive wire (the one connected to V) to the positive terminal on the DC power source, and connect the other end of the return wire (the one connected to RT) to the return terminal on the DC power source. When you are testing the switch, one power connection is sufficient.
Chapter 2 Switch Installation Verifying Switch Operation Figure 2-16 Completed DC Power Connections on the Power and Relay Connector 1 5 2 6 3 7 4 V RT A A 201818 V RT A A 8 1 Power source A positive connection 5 Power source B positive connection 2 Power source A return connection 6 Power source B return connection 3 External device 1, relay wire connection 7 External device 2, relay wire connection 4 External device 1, relay wire connection 8 External device 2, relay wire connect
Chapter 2 Switch Installation Verifying Switch Operation Attach the Power and Relay Connector to the Switch Follow these steps to attach the power and relay connectors to the front panel of the switch. Step 1 Insert the power and relay connector into the Pwr A receptacle on the switch front panel. See Figure 2-17.
Chapter 2 Switch Installation Verifying Switch Operation Running POST When the switch powers on, it automatically initiates a POST. The POST runs a series of tests that verify that the switch functions properly and ensures that it is ready to install.
Chapter 2 Switch Installation Installing the Switch Installing the Switch This section describes how to install the switch: Warning • Installing the Switch on a DIN Rail • Installing the Switch on the Wall • Installing the Switch in a Rack This equipment is supplied as “open type” equipment.
Chapter 2 Switch Installation Installing the Switch The illustrations in this procedure show how to install the switch as a standalone device. The same steps can be used to install a switch with expansion modules on the DIN rail. To attach the switch to a DIN rail, follow these steps. Step 1 Use a flathead screwdriver to press in the space next to the tab on each of the latches and turn the screw driver clockwise. See Figure 2-19.
Chapter 2 Switch Installation Installing the Switch Step 2 Push the DIN rail latches. See Figure 2-20. Pushing the DIN Rail Latches Out 201828 Figure 2-20 Step 3 Position the rear panel of the switch directly in front of the DIN rail, making sure that the DIN rail fits in the space between the two latches.
Chapter 2 Switch Installation Installing the Switch Step 4 Push the DIN rail latches in after the switch is over the DIN rail. See Figure 2-21. Pushing the DIN Rail Latches In 201829 Figure 2-21 Note If you are using a 15-mm DIN rail, rotate all the feet (see Figure 2-21) to the extended positions. Otherwise, rotate all the feet to the recessed positions. Figure 2-22 shows the two DIN rails. You can use either the 7.5-mm or the 15-mm DIN rail.
Chapter 2 Switch Installation Installing the Switch Figure 2-22 Mounting the Switch on a DIN Rail in a Parallel Position 2 4 1 3 1 15-mm DIN rail 3 7.5-mm DIN rail 2 Foot in extended position 4 Foot in recessed position After the switch is mounted on the DIN rail, connect the power and alarm wires, as described in the “Connecting Power and Alarm Circuits” section on page 2-32.
Chapter 2 Switch Installation Installing the Switch Step 1 If the DIN rail latches are pushed out, push in the DIN rail latches. See Figure 2-23.
Chapter 2 Switch Installation Installing the Switch Step 2 Rotate all feet to the recessed positions so that the switch can mount flat on the wall or panel. See Figure 2-22. Step 3 Position the rear panel of the switch against the wall or a panel in the desired location. See Figure 2-24. Figure 2-24 Mounting the Switch on the Wall 201833 1 Step 4 Place a number-10 screw that you provide through each DIN rail latch, and screw them into the wall.
Chapter 2 Switch Installation Installing the Switch Warning Note To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: • This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
Chapter 2 Switch Installation Installing the Switch Installing the Switch on a Rack 201831 Figure 2-26 . After the switch is mounted in the rack, connect the power and alarm wires, as described in the “Connecting Power and Alarm Circuits” section on page 2-32. For instructions on how to remove the switch from a rack, see the “Removing the Switch from a DIN Rail or a Rack” section on page 2-31.
Chapter 2 Switch Installation Connecting Power and Alarm Circuits Removing the Switch from the DIN Rail 201850 Figure 2-27 Step 4 Remove the switch from the DIN rail. Connecting Power and Alarm Circuits After the switch is installed, you are ready to connect the DC power and alarm relays.
Chapter 2 Switch Installation Connecting Power and Alarm Circuits Wiring the External Alarms The alarm relays on the switch are normally open. To connect an external alarm device to the relays, you must connect two relay contact wires to complete an electrical circuit. Because each external alarm device requires two connections to a relay, the switch supports a maximum of two external alarm devices. This procedure is optional.
Chapter 2 Switch Installation Connecting Power and Alarm Circuits Figure 2-29 Torquing the Power and Relay Connector Captive Screws 202030 V RT A A Step 5 Repeat Step 1 through Step 4 to insert the input and output wires of an additional external alarm device into the second power and relay connector.
Chapter 2 Switch Installation Connecting Power and Alarm Circuits Figure 2-30 shows the completed wiring for two power supplies and two external alarm devices.
Chapter 2 Switch Installation Connecting Destination Ports Connecting Destination Ports These section provide more information about connecting to the destination ports: • Connecting to 10/100 and 10/100/1000 Ports, page 2-36 • Installing and Removing SFP Modules, page 2-37 • Connecting to SFP Modules, page 2-41 • Connecting to a Dual-Purpose Port, page 2-42 • Connecting to 100BASE-FX Ports, page 2-43 Connecting to 10/100 and 10/100/1000 Ports The switch 10/100/1000 ports automatically configur
Chapter 2 Switch Installation Connecting Destination Ports Connecting to an Ethernet Port 201881 Figure 2-31 1 2 1 Step 2 10/100/1000 port 2 10/100 ports Connect the other end of the cable to an RJ-45 connector on the other device. The port LED turns on when both the switch and the connected device have established link. The port LED is amber while Spanning Tree Protocol (STP) discovers the topology and searches for loops. This can take up to 30 seconds, and then the port LED turns green.
Chapter 2 Switch Installation Connecting Destination Ports Caution When you use commercial SFP modules such as CWDM and 1000BX-U/D, reduce the maximum operating temperature by 59°F (15°C). The minimum operating temperature is 32°F (0°C). For detailed instructions on installing, removing, and cabling the SFP module, see your SFP module documentation. Installing SFP Modules into SFP Module Slots Figure 2-32 shows an SFP module that has a bale-clasp latch.
Chapter 2 Switch Installation Connecting Destination Ports Installing an SFP Module into an SFP Module Slot 201866 Figure 2-33 Step 5 Caution Remove the dust plugs from the SFP module optical ports, store them for later use. Do not remove the dust plugs from the SFP module port or the rubber caps from the fiber-optic cable until you are ready to connect the cable. The plugs and caps protect the SFP module ports and cables from contamination and ambient light.
Chapter 2 Switch Installation Connecting Destination Ports Step 6 Insert the LC cable connector into the SFP module. Removing SFP Modules from SFP Module Slots To remove an SFP module from a module receptacle, follow these steps: Step 1 Attach an ESD-preventive wrist strap to your wrist and to a grounded bare metal surface. Step 2 Disconnect the LC from the SFP module. Step 3 Insert a dust plug into the optical ports of the SFP module to keep the optical interfaces clean.
Chapter 2 Switch Installation Connecting Destination Ports Connecting to SFP Modules This section describes how to connect to a fiber-optic SFP port. To connect to an RJ-45 Gigabit Ethernet port instead of a fiber-optic port, see the “Connecting to a Dual-Purpose Port” section on page 2-42. For instructions on how to install or remove an SFP module, see the “Installing and Removing SFP Modules” section on page 2-37.
Chapter 2 Switch Installation Connecting Destination Ports The LED turns amber while the STP discovers the network topology and searches for loops. This process takes about 30 seconds, and then the port LED turns green. If the LED is off, the target device might not be turned on, there might be a cable problem, or there might be a problem with the adapter installed in the target device. See Chapter 3, “Troubleshooting,” for solutions to cabling problems.
Chapter 2 Switch Installation Connecting Destination Ports Figure 2-36 Connecting to a Dual-Purpose Port 1 201871 2 1 Step 2 LC connector 2 RJ-45 connector Connect the other end of the cable to the other device. By default, the switch detects whether an RJ-45 connector or SFP module is connected to a dual-purpose port and configures the port accordingly.
Chapter 2 Switch Installation Connecting the Switch to the Power Converter Figure 2-37 Connecting to a Fiber-Optic SFP Module Port 202031 1 1 LC connector Step 3 Insert the other cable end into a fiber-optic receptacle on a target device. Step 4 Observe the port status LED. The LED turns green when the switch and the target device have an established link. The LED turns amber while the STP discovers the network topology and searches for loops.
Chapter 2 Switch Installation Connecting the Switch to the Power Converter Attaching the Power Converter to the Switch Follow these directions to connect the power converter to the switch: Step 1 Remove the left side panel of the switch by firmly grasping both sides of it in the middle and pulling it outward. If necessary, use a screwdriver to open the side panel. See Figure 2-38.
Chapter 2 Switch Installation Connecting the Switch to the Power Converter Step 3 Put the two modules together so that the power module fits in the switch recess. Step 4 Push the upper module latches down and the lower module latches up to secure the power converter to the switch. See Figure 2-40. Figure 2-40 Pushing the Latches In Pwr A (24VD C or 48 VDC) Rtn A Major Alarm 5 ! WARNING This unit might have power cord.
Chapter 2 Switch Installation Connecting the Switch to the Power Converter Follow these steps to connect DC power from the power converter to the switch module. Step 1 Locate the DC power clip in the power converter accessory kit. Step 2 Position the power clip so that the two-pin connector is over the power converter and the four-pin connector is over the switch Pwr A connector, and then slide the power clip into these two connectors. See Figure 2-41.
Chapter 2 Switch Installation Connecting the Switch to the Power Converter Table 2-2 AC-Power Cord-Color Codes Europe (International) Color Meaning Brown Line Blue Neutral Green/yellow Earth ground United States Color Meaning Black Line White Neutral Green Earth ground To prepare an AC power cord to connect to the power converter, strip the inner wire insulation to 0.25 inch (6.3 mm) ± 0.02 inch (0.5 mm). See Figure 2-42. Figure 2-42 Preparing the AC Power Cord 1 280368 2 1 0.
Chapter 2 Switch Installation Connecting the Switch to the Power Converter Step 1 Do not insert the cord into the AC outlet until you have completed wiring the line, neutral, and ground connections. Remove the plastic cover from the input power terminals and set it aside. See Figure 2-43. Figure 2-43 AC/DC Power Input Terminal Block 1 1 Step 2 202299 Caution Ground wire Insert the exposed ground wire lead into the power converter ground wire connection.
Chapter 2 Switch Installation Connecting the Switch to the Power Converter Figure 2-44 Connecting AC Power to the Power Converter 1 2 202300 3 Step 3 Note 1 Ground 2 AC neutral 3 AC line Tighten the ground wire terminal block screw. The torque should not exceed 10 in-lb. Step 4 Insert the line and neutral wire leads into the terminal block line and neutral connections. See Figure 2-44. Make sure that you cannot see any wire lead.
Chapter 2 Switch Installation Connecting the Switch to the Power Converter Connecting the Power Converter to a DC Power Source You can also connect the power converter to a DC power source. The power converter adapts the power source voltage to the 24 VDC that the switch requires. Follow these steps to connect the power converter to a DC power source. Note Warning Step 1 Use copper conductors only, rated at a minimum temperature of 167°F (75°C).
Chapter 2 Switch Installation Connecting the Switch to the Power Converter Figure 2-45 AC/DC Power Input Terminal Block Wire Connections to a DC Source 1 2 202301 3 Warning 1 Earth ground wire connection 2 Return wire connection (to DC return) 3 Positive DC connection An exposed wire lead from a DC-input power source can conduct harmful levels of electricity. Be sure that no exposed portion of the DC-input power source wire extends from the power and relay connector.
Chapter 2 Switch Installation Where to Go Next Applying Power to the Power Converter Move the circuit breaker for the AC outlet or the DC control circuit to the on position. The LED on the power converter front panel is green when the unit is operating normally. The LED is off when the unit is not powered or is not operating normally. After the power is connected, the switch automatically begins the power-on self- test (POST), a series of tests that verifies that the switch functions properly.
Chapter 2 Switch Installation Where to Go Next Cisco IE 3000 Switch Hardware Installation Guide 2-54 OL-13017-01
CH A P T E R 3 Troubleshooting This chapter provides these topics for troubleshooting problems: • Diagnosing Problems, page 3-1 • How to Clear the Switch IP Address and Configuration, page 3-5 • How to Recover Passwords, page 3-5 • Finding the Switch Serial Number, page 3-6 Diagnosing Problems The LEDs on the front panel provide troubleshooting information about the switch. They show power-on self-test (POST) failures, port-connectivity problems, and overall switch performance.
Chapter 3 Troubleshooting Diagnosing Problems Warning If you connect or disconnect the console cable with power applied to the switch or any device on the network, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding. To verify switch operation, perform POST on the switch in a nonhazardous location before installation.
Chapter 3 Troubleshooting Diagnosing Problems Link Status Verify that both sides have link. A single broken wire or one shutdown port can cause one side to show link, but the other side does not have link. A link LED does not guarantee that the cable is fully functional. The cable might have encountered physical stress that causes it to function at a marginal level. If the link light for the port does not come on: • Connect the cable from the switch to a known good device.
Chapter 3 Troubleshooting Diagnosing Problems Spanning Tree Loops Spanning Tree Protocol (STP) loops can cause serious performance issues that look like port or interface problems. In this situation, the switch bandwidth is used over and over again by the same frames, leaving little room for legitimate traffic. Loops can be caused by a unidirectional link.
Chapter 3 Troubleshooting How to Clear the Switch IP Address and Configuration Cabling Distance If the port statistics show excessive FCS, late-collision, or alignment errors, verify that the cable distance from the switch to the connected device meets the recommended guidelines. See the “Cable and Connectors” section on page C-1 for cabling guidelines. How to Clear the Switch IP Address and Configuration Follow these steps to return your switch to the factory default settings.
Chapter 3 Troubleshooting Finding the Switch Serial Number Finding the Switch Serial Number If you contact Cisco Technical Assistance, you need to know the serial number of your switch. See Figure 3-1 and Figure 3-2 to find the serial number on your switch or module. You can also use the show version privileged EXEC command to get the switch serial number.
A P P E N D I X A Technical Specifications Table A-1 lists the operating temperatures for the Cisco IE 3000 switches, modules, and power convertor. Table A-2 lists the technical specifications for the switches and modules. Table A-3 lists the technical specifications for the Cisco IE 3000 switch power converter. The operating temperature for the Cisco IE 3000 switches, modules, and the power convertor varies among environments, based on factors such as the system configuration and enclosure types.
Appendix A Table A-2 Technical Specifications Cisco IE 3000 Series Technical Specifications Environmental Ranges Storage temperature –40 to 185°F (–40 to 85°C) Operating humidity 5 to 95% (noncondensing) Operating shock 20 g at 11 ms Operating altitude Up to 13,000 ft (3962 m) Storage altitude Up to 40,000 ft (12,192 m) Power Requirements DC input voltage Cisco IE-3000-8TC and Cisco IE-3000-4TC: • Range: 18 to 60 VDC • Nominal: 24 or 48 VDC The DC-input power supply is an SELV circuit, an
Appendix A Technical Specifications Table A-3 Technical Specifications for the Power Converter Environmental Ranges Operating temperature –29 to 165°F (–34 to 74°C) Storage temperature –40 to 185°F (–40 to 85°C) Operating altitude Up to 13,000 ft (3962 m) Storage altitude Up to 40,000 ft (12,192 m) Thermal spacing 3.54 in. (90 mm) exposed side 4.13 in.
Appendix A Technical Specifications Cisco IE 3000 Switch Hardware Installation Guide A-4 OL-13017-01
A P P E N D I X B Installation In a Hazardous Environment This chapter describes how to install your switch, interpret the power-on self-test (POST), and connect the switch to other devices when in a hazardous environment.
Appendix B Installation In a Hazardous Environment Preparing for Installation Warnings These warnings are translated into several languages in the Regulatory Compliance and Safety Information Guide. Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.
Appendix B Installation In a Hazardous Environment Preparing for Installation Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of: 140°F (60°C) Statement 1047 Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074 Warning To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 4.13 in. (105 mm).
Appendix B Installation In a Hazardous Environment Preparing for Installation Warning This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in IEC publication 60664-1), and at altitudes up to 2000 meters without derating. Statement 1068 Warning Explosion Hazard—Do not connect or disconnect wiring while the field-side power is on; an electrical arc can occur.
Appendix B Installation In a Hazardous Environment North American Hazardous Location Approval North American Hazardous Location Approval The following information applies when operating this equipment in hazardous locations: English: Français: Products marked "Class I, Div 2, GP A, B, C, D" are suitable for use in Class I Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous locations only.
Appendix B Installation In a Hazardous Environment North American Hazardous Location Approval • This equipment is considered Group 1, Class A industrial equipment, according to IEC/CISPR Publication 11. Without appropriate precautions, there may be potential difficulties ensuring electromagnetic compatibility in other environments due to conducted as well as radiated disturbance. • This equipment is supplied as open-type equipment.
Appendix B Installation In a Hazardous Environment North American Hazardous Location Approval • Clearance to front and rear panels meets these conditions: – Front-panel LEDs can be easily read. – Access to ports is sufficient for unrestricted cabling. – Front-panel direct current (DC) power and relay connector is within reach of the connection to the DC power source. • Airflow around the switch and through the vents is unrestricted.
Appendix B Installation In a Hazardous Environment Adding Modules to the Switch For multimode (MM) connections, you can connect a 100BASE-FX port to a port on a target device by using an dual-LC connector. Adding Modules to the Switch The Cisco IE-3000-4TC or the Cisco IE-3000-8TC switch can operate as standalone devices with four or eight Fast Ethernet ports, respectively.
Appendix B Installation In a Hazardous Environment Adding Modules to the Switch Expansion Module Configurations To increase the number of ports, add one or two expansion modules to the switch. If you are installing only one module, it can be either a Cisco IEM-3000-8TM or a Cisco IEM-3000-8FM. If you are installing two modules, the first must be a Cisco IEM-3000-8TM, and the second can be either a Cisco IEM-3000-8TM or a Cisco IEM-3000-8FM. You cannot add two Cisco IEM-3000-8FM expansion modules.
Appendix B Installation In a Hazardous Environment Adding Modules to the Switch Figure B-1 Sample Combinations of Expansion Modules 1 2 3 201827 4 Cisco IE 3000 Switch Hardware Installation Guide B-10 OL-13017-01
Appendix B Installation In a Hazardous Environment Adding Modules to the Switch 1 Cisco IE-3000-4TC switch with Cisco IEM-3000-8TM and Cisco IEM-3000-8FM expansion modules (12 FE and 8 FX ports) 2 Cisco IE-3000-4TC switch with one Cisco IEM-3000-8FM expansion module (4 FE and 8 FX ports) 3 Cisco IE-3000-4TC switch with one Cisco IEM-3000-8TM expansion modules (12 FE ports) 4 Cisco IE-3000-4TC switch with two Cisco IEM-3000-8TM expansion modules (20 FE ports) Connecting Modules Follow these directi
Appendix B Installation In a Hazardous Environment Adding Modules to the Switch Step 3 Push up the upper module latches (at the top of the switch and the module). See Figure B-4. Push down the lower module latches (at the bottom of the switch and the module). Pushing the Module Latches Up 201824 Figure B-4 Step 4 Align the connectors on the switch and the module, and slide the switch and the module together to make the connection. See Figure B-5.
Appendix B Installation In a Hazardous Environment Installing or Removing the Compact Flash Memory Card Pushing the Module Latches In 201826 Figure B-6 Step 6 (Optional) If the first module attached was an Cisco IEM-3000-8TM, you can connect another Cisco IEM-3000-8TM or Cisco IEM-3000-8FM expansion module. Follow Step 1 to Step 5 to connect the module.
Appendix B Installation In a Hazardous Environment Verifying Switch Operation Follow these directions to remove or replace the compact flash memory card: Step 1 Locate the compact flash memory card slot on the bottom of the switch. See Figure B-7. Removing the Compact Flash Memory Card from the Switch 201851 Figure B-7 1 Step 2 Bottom of switch Install or remove the card, as desired: • To remove the card, grasp the card top, and pull it out.
Appendix B Installation In a Hazardous Environment Verifying Switch Operation Connecting a PC or a Terminal to the Console Port To connect a PC to the console port, use the supplied RJ-45-to-DB-9 adapter cable. To connect a terminal to the console port, you need to provide an RJ-45-to-DB-25 female DTE adapter. You can order a kit (part number ACS-DSBUASYN=) with that adapter from Cisco. For console-port and adapter-pinout information, see the “Cable and Adapter Specifications” section on page C-4.
Appendix B Installation In a Hazardous Environment Verifying Switch Operation Connecting to the Console Port 201868 Figure B-8 Step 4 Attach the appropriate adapter to the terminal, if needed. Step 5 Connect the other end of the adapter cable to the PC or terminal adapter. Step 6 Start the terminal-emulation software on the PC.
Appendix B Installation In a Hazardous Environment Verifying Switch Operation Obtain these necessary tools and equipment: • Ratcheting torque flathead screwdriver that exerts up to 15 inch-pounds (in-lb) of pressure • Ring terminal lug (such as Thomas & Bett part number 10RCR or equivalent) • Crimping tool (such as Thomas & Bett part number WT2000, ERG-2001, or equivalent) • 10-gauge copper ground wire (such as Belden part number 9912 or equivalent) • For DC power connections, use UL- and CSA-rat
Appendix B Installation In a Hazardous Environment Verifying Switch Operation Figure B-9 Stripping the Ground Wire 3 2 Step 3 1 0.5 in. (12.7 mm) ± 0.02 in. (0.5 mm) 2 Insulation 104908 1 3 Wire lead Insert the ground wire into the ring terminal lug, and using a crimping tool, crimp the ring terminal to the wire. Crimping the Ring Terminal 76666 Figure B-10 Step 4 Slide the ground screw through the ring terminal.
Appendix B Installation In a Hazardous Environment Verifying Switch Operation Torquing Ground-Lug Screws 201696 Figure B-11 1 1 Step 7 Ground cable Attach the other end of the ground wire to a grounded bare metal surface, such as a ground bus, a grounded DIN rail, or a grounded bare rack.
Appendix B Installation In a Hazardous Environment Verifying Switch Operation Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. Statement 1003 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Caution You must connect the switch only to a DC-input power source that has an input supply voltage from 18 to 60 VDC.
Appendix B Installation In a Hazardous Environment Verifying Switch Operation Step 5 Warning Insert the exposed part of the positive wire into the connection labeled V and the exposed part of the return wire into the connection labeled RT. See Figure B-14. Make sure that you cannot see any wire lead. Only wire with insulation should extend from the connector. An exposed wire lead from a DC-input power source can conduct harmful levels of electricity.
Appendix B Installation In a Hazardous Environment Verifying Switch Operation Figure B-15 Torquing the Power and Relay Connector Captive Screws 1 201817 V RT A A 1 Step 7 Power and relay connector captive screws Connect the other end of the positive wire (the one connected to V) to the positive terminal on the DC power source, and connect the other end of the return wire (the one connected to RT) to the return terminal on the DC power source.
Appendix B Installation In a Hazardous Environment Verifying Switch Operation Figure B-16 shows the completed DC-input wiring on a power and relay connector for a primary power source and an optional secondary power source.
Appendix B Installation In a Hazardous Environment Verifying Switch Operation Attach the Power and Relay Connector to the Switch Follow these steps to attach the power and relay connectors to the front panel of the switch. Step 1 Warning Insert the power and relay connector into the Pwr A receptacle on the switch front panel. See Figure B-17. When you connect or disconnect the power and relay connector with power applied, an electrical arc can occur.
Appendix B Installation In a Hazardous Environment Verifying Switch Operation Running POST When the switch powers on, it automatically initiates a POST. The POST runs a series of tests that verify that the switch functions properly and ensures that it is ready to install.
Appendix B Installation In a Hazardous Environment Installing the Switch Installing the Switch These sections describes how to install the switch: Warning • Installing the Switch on a DIN Rail • Installing the Switch on a Wall • Installing the Switch in a Rack This equipment is supplied as “open type” equipment.
Appendix B Installation In a Hazardous Environment Installing the Switch Installing the Switch on a DIN Rail The switch ships with latches on the rear panel for a mounting on a DIN rail. See Figure B-18. Cisco IE 3000 Switch Rear Panel 203976 Figure B-18 You can install the switch as a standalone device on the DIN rail or with the expansion modules already connected. You must connect the expansion modules to the switch before installing the switch on the DIN rail.
Appendix B Installation In a Hazardous Environment Installing the Switch To attach the switch to a DIN rail, follow these steps. Step 1 Use a tool such as a flathead screw driver to press in the space next to the tab on each of the latches and turn the screw driver clockwise. See Figure B-19.
Appendix B Installation In a Hazardous Environment Installing the Switch Step 2 Push the DIN rail latches out. See Figure B-20. Pushing the DIN Rail Latches Out 201828 Figure B-20 Step 3 Position the rear panel of the switch directly in front of the DIN rail, making sure that the DIN rail fits in the space between the two latches.
Appendix B Installation In a Hazardous Environment Installing the Switch Step 4 Push the DIN rail latches in after the switch is over the DIN rail. See Figure B-21. Pushing the DIN Rail Latches In 201829 Figure B-21 Note If you are using a 15-mm DIN rail, rotate all the feet (see Figure B-21) to the extended positions. Otherwise, rotate all the feet to the recessed positions. Figure B-22 shows the two DIN rails. You can use either the 7.5-mm or the 15-mm DIN rail.
Appendix B Installation In a Hazardous Environment Installing the Switch Figure B-22 Mounting the Switch on a DIN Rail in a Parallel Position 2 4 1 3 1 15-mm DIN rail 3 7.5-mm DIN rail 2 Foot in extended position 4 Foot in recessed position After the switch is mounted on the DIN rail, connect the power and alarm wires, as described in the “Connecting Power and Alarm Circuits” section on page B-36.
Appendix B Installation In a Hazardous Environment Installing the Switch Step 1 If the DIN rail latches are pushed out, push in the DIN rail latches. See Figure B-23.
Appendix B Installation In a Hazardous Environment Installing the Switch Step 2 Rotate all feet to the recessed positions so that the switch can mount flat on the wall or panel. See Figure B-22. Step 3 Position the rear panel of the switch against the wall or a panel in the desired location. See Figure B-24. Figure B-24 Mounting the Switch on the Wall 201833 1 Step 4 Place a number-10 screw that you provide through each DIN rail latch, and screw them into the wall.
Appendix B Installation In a Hazardous Environment Installing the Switch Warning Note To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: • This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
Appendix B Installation In a Hazardous Environment Installing the Switch Installing the Switch on a Rack 201831 Figure B-26 . After the switch is mounted in the rack, connect the power and alarm wires, as described in the “Connecting Power and Alarm Circuits” section on page B-36. For instructions on how to remove the switch from a rack, see the “Removing the Switch from a DIN Rail or a Rack” section on page B-35.
Appendix B Installation In a Hazardous Environment Connecting Power and Alarm Circuits Removing the Switch from the DIN Rail 201850 Figure B-27 Step 4 Remove the switch from the DIN rail. Connecting Power and Alarm Circuits After the switch is installed, you are ready to connect the DC power and alarm relays.
Appendix B Installation In a Hazardous Environment Connecting Power and Alarm Circuits Information about the Sealed Relay Device We recommend that you periodically inspect the sealed relay device. Inspect the device for any degradation of materials. If any degradation is found, replace the complete product, not only the sealed device.
Appendix B Installation In a Hazardous Environment Connecting Power and Alarm Circuits Wiring the External Alarms The alarm relays on the switch are normally open. To connect an external alarm device to the relays, you must connect two relay contact wires to complete an electrical circuit. Because each external alarm device requires two connections to a relay, the switch supports a maximum of two external alarm devices. This procedure is optional.
Appendix B Installation In a Hazardous Environment Connecting Power and Alarm Circuits Step 4 Caution Use a ratcheting torque flathead screwdriver to torque the power and relay connector captive screw (above the installed wire leads) to 2 in-lb. See Figure B-29 for details. Do not over-torque the power and relay connector captive screws. The torque should not exceed 2 in-lb.
Appendix B Installation In a Hazardous Environment Connecting Power and Alarm Circuits Figure B-30 shows the completed wiring for two power supplies and two external alarm devices.
Appendix B Installation In a Hazardous Environment Connecting Destination Ports Connecting Destination Ports These section provide more information about connecting to the destination ports: • Connecting to 10/100 and 10/100/1000 Ports, page B-41 • Installing and Removing SFP Modules, page B-42 • Connecting to SFP Modules, page B-45 • Connecting to a Dual-Purpose Port, page B-46 • Connecting to 100BASE-FX Ports, page B-48 Connecting to 10/100 and 10/100/1000 Ports The switch 10/100/1000 ports au
Appendix B Installation In a Hazardous Environment Connecting Destination Ports Connecting to an Ethernet Port 201881 Figure B-31 1 2 1 Step 2 10/100/1000 port 2 10/100 ports Connect the other end of the cable to an RJ-45 connector on the other device. The port LED turns on when both the switch and the connected device have established a link. The port LED is amber while Spanning Tree Protocol (STP) discovers the topology and searches for loops.
Appendix B Installation In a Hazardous Environment Connecting Destination Ports Caution When you use commercial SFP modules such as CWDM and 1000BX-U/D, reduce the maximum operating temperature by 59°F (15°C). The minimum operating temperature is 32°F (0°C). For detailed instructions on installing, removing, and cabling the SFP module, see your SFP module documentation. Installing SFP Modules into SFP Module Slots Figure B-32 shows an SFP module that has a bale-clasp latch.
Appendix B Installation In a Hazardous Environment Connecting Destination Ports Installing an SFP Module into an SFP Module Slot 201866 Figure B-33 Step 5 Caution Step 6 Remove the dust plugs from the SFP module optical ports, store them for later use. Do not remove the dust plugs from the SFP module port or the rubber caps from the fiber-optic cable until you are ready to connect the cable. The plugs and caps protect the SFP module ports and cables from contamination and ambient light.
Appendix B Installation In a Hazardous Environment Connecting Destination Ports Removing a Bale-Clasp Latch SFP Module by Using a Flat-Blade Screwdriver 201867 Figure B-34 1 1 Bale clasp Step 5 Grasp the SFP module between your thumb and index finger, and carefully remove it from the module slot. Step 6 Place the removed SFP module in an antistatic bag or other protective environment. Connecting to SFP Modules This section describes how to connect to a fiber-optic SFP port.
Appendix B Installation In a Hazardous Environment Connecting Destination Ports Step 1 Remove the rubber plugs from the module port and fiber-optic cable, and store them for future use. Step 2 Insert one end of the fiber-optic cable into the SFP module port. See Figure B-35. Figure B-35 Connecting to a Fiber-Optic SFP Module Port 201869 1 1 LC connector Step 3 Insert the other cable end into a fiber-optic receptacle on a target device. Step 4 Observe the port status LED.
Appendix B Installation In a Hazardous Environment Connecting Destination Ports Caution Do not remove the rubber plugs from the SFP module port or the rubber caps from the fiber-optic cable until you are ready to connect the cable. The plugs and caps protect the SFP module ports and cables from contamination and ambient light. Before connecting to the SFP module, be sure that you understand the port and cabling stipulations in the “Preparing for Installation” section on page B-1.
Appendix B Installation In a Hazardous Environment Connecting Destination Ports Connecting to 100BASE-FX Ports Follow these steps to connect a fiber-optic cable to an Cisco IEM-3000-8FM expansion module: Warning Caution Class 1 laser product. Statement 1008 Do not remove the rubber plugs from the SFF module port or the rubber caps from the fiber-optic cable until you are ready to connect the cable. The plugs and caps protect the SFF module ports and cables from contamination and ambient light.
Appendix B Installation In a Hazardous Environment Connecting the Switch to the Power Converter If an LED is off, the target device might not be turned on, there might be a cable problem, or there might be a problem with the adapter installed in the target device. See Chapter 3, “Troubleshooting,” for solutions to cabling problems. Step 5 If necessary, reconfigure and restart the switch or target device.
Appendix B Installation In a Hazardous Environment Connecting the Switch to the Power Converter Step 1 Remove the left side panel of the switch by firmly grasping both sides of it in the middle and pulling it outward. If necessary, use a screwdriver to open the side panel. See Figure B-38.
Appendix B Installation In a Hazardous Environment Connecting the Switch to the Power Converter Step 2 Push the upper modules latches (at the top of the switch and the power converter) up and the lower module latches (at the bottom of the switch and the power converter) down. See Figure B-39. Pushing the Module Latches Up and Positioning the Hardware 202296 Figure B-39 Step 3 Put the two modules together so that the power module fits in the switch recess.
Appendix B Installation In a Hazardous Environment Connecting the Switch to the Power Converter Installing the Power Converter on a DIN Rail, Wall, or Rack Adapter You install the power converter on a DIN rail, wall, or rack as you would a switch module. You should first attach the power converter to the switch and then install the entire switch assembly on the DIN rail, wall, or rack adapter.
Appendix B Installation In a Hazardous Environment Connecting the Switch to the Power Converter Figure B-41 Connecting Wires to the Power Converter DC Output Terminal Block 3 2 1 5 1 6 CONSOLE 2 7 3 8 2 Step 3 Caution 4 1 DC power clip 2 Two-pin connector on the power convertor 202298 1 3 Four-pin connector on the switch Use a ratcheting torque flathead screwdriver to tighten the captive screw to 2 in-lb. Do not over-torque the power and relay connector captive screws.
Appendix B Installation In a Hazardous Environment Connecting the Switch to the Power Converter Table 2-2 AC-Power Cord-Color Codes Europe (International) Color Meaning Brown Line Blue Neutral Green/yellow Earth ground United States Color Meaning Black Line White Neutral Green Earth ground To prepare an AC power cord to connect to the power converter, strip the inner wire insulation to 0.25 inch (6.3 mm) ± 0.02 inch (0.5 mm). See Figure B-42.
Appendix B Installation In a Hazardous Environment Connecting the Switch to the Power Converter Step 1 Do not insert the cord into the AC outlet until you finish wiring the line, neutral, and ground connections. Remove the plastic cover from the input power terminals and set it aside. See Figure B-43. Figure B-43 AC/DC Power Input Terminal Block 1 1 Step 2 202299 Caution Ground wire Insert the exposed ground wire lead into the power converter ground wire connection.
Appendix B Installation In a Hazardous Environment Connecting the Switch to the Power Converter Figure B-44 Connecting AC Power to the Power Converter 1 2 202300 3 Step 3 Note 1 Ground 2 AC neutral 3 AC line Tighten the ground wire terminal block screw. The torque should not exceed 10 in-lb. Step 4 Insert the line and neutral wire leads into the terminal block line and neutral connections. See Figure B-44. Make sure that you cannot see any wire lead.
Appendix B Installation In a Hazardous Environment Connecting the Switch to the Power Converter Connecting the Power Converter to a DC Power Source You can also connect the power converter to a DC power source. The power converter adapts the power source voltage to the 24 VDC that the switch requires. Follow these steps to connect the power converter to a DC power source. Note Warning Step 1 Use copper conductors only, rated at a minimum temperature of 167°F (75°C).
Appendix B Installation In a Hazardous Environment Connecting the Switch to the Power Converter Figure B-45 AC/DC Power Input Terminal Block Wire Connections to a DC Source 1 2 202301 3 Warning 1 Earth ground wire connection 2 Return wire connection (to DC return) 3 Positive DC connection An exposed wire lead from a DC-input power source can conduct harmful levels of electricity. Be sure that no exposed portion of the DC-input power source wire extends from the power and relay connector.
Appendix B Installation In a Hazardous Environment Where to Go Next Applying Power to the Power Converter Move the circuit breaker for the AC outlet or the DC control circuit to the on position. The LED on the power converter front panel is green when the unit is operating normally. The LED is off when the unit is not powered or is not operating normally.
Appendix B Installation In a Hazardous Environment Where to Go Next Cisco IE 3000 Switch Hardware Installation Guide B-60 OL-13017-01
A P P E N D I X C Cable and Connectors This appendix describes the switch ports and the cables and adapters that you use to connect the switch to other devices. Connector Specifications These sections describe the connectors used with the Cisco IE 3000 switch. 10/100 Ports The 10/100 and 10/100/1000 Ethernet ports on switches use standard RJ-45 connectors and Ethernet pinouts with internal crossovers. Figure C-1 and Figure C-2 show the pinouts.
Appendix C Cable and Connectors Connector Specifications Use a straight-through cable to connect two ports only when one port is designated with an X. Use a crossover cable to connect two ports when both ports are designated with an X or when both ports do not have an X.
Appendix C Cable and Connectors Connector Specifications 100BASE-FX Ports The 100BASE-FX ports use MT-RJ connectors. See Figure C-3. The 100BASE-FX ports use 50/125- or 62.5/125-micron multimode fiber-optic cabling. Fiber-Optic SFP Module LC Connector 58476 Figure C-3 Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments.
Appendix C Cable and Connectors Cable and Adapter Specifications Dual-Purpose Ports The Ethernet port on a dual-purpose port uses standard RJ-45 connectors. Figure C-2 shows the pinouts. The SFP module slot on a dual-purpose port uses SFP modules for fiber-optic and copper uplink ports. See the switch release notes for a list of supported SFP modules. The auto-MDIX feature is enabled by default.
Appendix C Cable and Connectors Cable and Adapter Specifications Table C-1 Rugged Fiber-Optic SFP Module Port Cabling Specifications Wavelength (nanometers) Fiber Type Core Size/Cladding Size (micron) Modal Bandwidth (MHz/km)1 Cable Distance 100BASE-FX (GLC-FE-100FX-RGD) (SFF ports) 1310 MMF 50/125 62.5/125 500 500 6562 feet (2 km) 6562 feet (2 km) 100BASE-LX (GLC-FE-100LX-RGD) 1310 SMF G.6522 — 32,810 feet (10 km) 1000BASE-SX (GLC-SX-MM-RGD) 850 MMF 62.5/125 62.
Appendix C Cable and Connectors Cable and Adapter Specifications Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports Figure C-7 and Figure C-8 show the schematics of four twisted-pair cables for 10/100/1000 ports on the Cisco IE 3000 switches.
Appendix C Cable and Connectors Cable and Adapter Specifications Crossover Cable and Adapter Pinouts This section describes how to identify a crossover cable and also describes the adapter pinouts. Identifying a Crossover Cable To identify a crossover cable, compare the two modular ends of the cable. Hold the cable ends side-by-side, with the tab at the back.
Appendix C Cable and Connectors Cable and Adapter Specifications Four Twisted-Pair Crossover Cable Schematics for 10/100/1000 and 1000BASE-T SFP Module Ports Switch Switch 1 TPO+ 1 TP0+ 2 TPO- 2 TP0- 3 TP1+ 3 TP1+ 6 TP1- 6 TP1- 4 TP2+ 4 TP2+ 5 TP2- 5 TP2- 7 TP3+ 7 TP3+ 8 TP3- 8 TP3- 65274 Figure C-11 Adapter Pinouts Table C-2 lists the pinouts for the console port, the RJ-45-to-DB-9 adapter cable, and the console device.
Appendix C Cable and Connectors Cable and Adapter Specifications Table C-3 lists the pinouts for the console port, RJ-45-to-DB-25 female DTE adapter, and the console device. Note The RJ-45-to-DB-25 female DTE adapter is not supplied with the switch. You can order a kit (part number ACS-DSBUASYN=) containing this adapter from Cisco.
Appendix C Cable and Connectors Cable and Adapter Specifications Cisco IE 3000 Switch Hardware Installation Guide C-10 OL-13017-01
A P P E N D I X D Configuring the Switch with the CLI-Based Setup Program This appendix provides a command-line interface (CLI)-based setup procedure for a standalone switch. For information about setting up the switch by using Express Setup, see the Cisco IE 3000 Switch Getting Started Guide. Before connecting the switch to a power source, review the safety warnings in Chapter 2, “Switch Installation.
Appendix D Configuring the Switch with the CLI-Based Setup Program Entering the Initial Configuration Information The PC or terminal displays the bootloader sequence. Press Enter to display the setup prompt. Follow the steps described in the “Entering the Initial Configuration Information” section on page D-2. Entering the Initial Configuration Information To set up the switch, you need to complete the setup program, which runs automatically after the switch is powered on.
Appendix D Configuring the Switch with the CLI-Based Setup Program Entering the Initial Configuration Information Step 3 Enter an enable secret password, and press Return. The password can be from 1 to 25 alphanumeric characters, can start with a number, is case sensitive, allows spaces, but ignores leading spaces. The secret password is encrypted, and the enable password is in plain text. Enter enable secret: secret_password Step 4 Enter an enable password, and press Return.
Appendix D Configuring the Switch with the CLI-Based Setup Program Entering the Initial Configuration Information interface FastEthernet1/1 ! interface FastEthernet1/2 ! interface FastEthernet1/3 ! ...(output abbreviated) ! interface GigabitEthernet1/1 ! interface GigabitEthernet1/2 ! end Step 10 These choices appear: [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit.
I N D EX Numerics C 10/100/1000 ports cables cable lengths 2-4, B-6 connecting to 2-36, B-41 described crossover four twisted-pair pinout, 1000BASE-T ports 1-5 identifying 10/100 ports cable lengths 2-4, B-6 connecting to 2-36, B-41 described using optical 1000BASE-T ports C-5 C-4 straight-through four twisted-pair pinout, 1000BASE-T ports 2-4, B-6 cable specifications described C-5 two twisted-pair pinout 2-43, B-48 using 1-5 C-1 10/100 ports auto-MDIX AC/DC power converter,
Index connecting duplex, troubleshooting to 10/100/1000 ports 2-36, B-41 to 100BASE-FX ports to console port to DC power 2-43, B-48 to external alarm devices to PC E 2-12 to 2-13, B-15 to B-16 2-16 to 2-22, B-19 to B-25 to modules electrical noise, avoiding 2-33 to 2-35, B-38 to B-40 2-8, B-11 to SFP modules to terminal environmental ranges 2-4, B-7 A-3 environmental temperatures 2-12 to 2-13, B-15 to B-16 to power converter 3-4 ESD, requirements 2-44 to 2-53, B-49 to B-59 A-2 2-3,
Index hazardous location (continued) installation (continued) grounding the switch B-17 installation guidelines B-5 required clearance SFP modules installing compact flash memory card installing the switch running POST verifying switch operation wall B-25 hazardous location warnings console cable DC power B-3 2-33 to 2-35, B-38 to B-40 J B-3 jewelry removal warning disconnecting the power and relay connector disconnecting the wiring B-3 L B-4 power and relay connector B-3, B-24 substit
Index LEDs N 3-1 results Network Assistant noise, electrical 2-53, B-59 2-22, 2-53, 3-1, B-25, B-59 running at power on 2-4, B-7 3-1 power connecting to O operating temperature AC 2-47, B-53 DC 2-16 to 2-22, B-19 to B-25 requirements A-1 A-2 to A-3 power and alarm circuits connecting P B-36 sealed relay device patch cables, MT-RJ physical dimensions pinouts power and relay connector 2-5, B-8 PC, connecting to switch B-37 connecting to the switch 2-12 to 2-13, B-15 to B-16 descr
Index removing the switch from a DIN rail or a rack 2-31 to 2-32, B-35 to B-36 removing the switch from parallel and face-down mounted positions 2-31 to 2-32, B-35 to B-36 RJ-45 connector, console port C-4 T technical specifications A-1 to A-2 Telnet, and accessing the CLI temperature, operating 1-14 A-3 terminal, connecting to a switch S terminal-emulation software 2-2 to 2-4, B-2 to B-4 bad or damaged cable C-3 serial number location 3-6 SFP modules bale-clasp latch removal cables conne
Index warnings (continued) lightning activity 2-2, B-2 national laws and regulations qualified personnel 2-2, B-2 restricted access areas supply wires wiring the relays 2-2 2-2, B-2 2-51, B-3, B-57 2-33 to 2-35, B-38 to B-40 Cisco IE 3000 Switch Hardware Installation Guide IN-6 OL-13017-01