Cisco IE 2000 Switch Hardware Installation Guide June 2013 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
CONTENTS Preface vii Audience Purpose vii vii Conventions vii Related Publications viii Obtaining Documentation, Obtaining Support, and Security Guidelines CHAPTER 1 Product Overview 1-1 Switch Models 1-2 viii Front Panel 1-5 10/100BASE-T Downlink Ports 1-8 Power over Ethernet Ports 1-9 10/100BASE-T Uplink Ports 1-9 10/100/1000BASE-T Uplink Ports 1-9 100 Mb/s SFP Module Uplink Slots 1-9 100/1000 Mb/s SFP Module Uplink Slots 1-9 Dual-Purpose Fast Ethernet Uplink Ports 1-9 Dual-Purpose Gigabi
Contents Management Options 1-21 Network Configurations CHAPTER 2 Switch Installation 1-22 2-1 Preparing for Installation 2-1 Warnings 2-1 Additional Information for Installation in a Hazardous Environment 2-3 Hazardous Area Installation Warnings 2-3 North American Hazardous Location Approval 2-5 EMC Environmental Conditions for Products Installed in the European Union Installation Guidelines 2-5 Environment and Enclosure Guidelines 2-5 General Guidelines 2-6 Verifying Package Contents 2-7 Installi
Contents Wiring the Protective Ground and DC Power for Alarm Circuits Wiring the External Alarms 2-35 Attaching the Alarm Connector to the Switch 2-38 2-34 Connecting Destination Ports 2-39 Connecting to 10/100 and 10/100/1000 Ports 2-40 Installing and Removing SFP Modules 2-42 Installing SFP Modules into SFP Module Slots 2-42 Removing SFP Modules from SFP Module Slots 2-43 Connecting to SFP Modules 2-44 Connecting to a Dual-Purpose Port 2-46 Verifying Switch Operation Where to Go Next CHAPTER 3 Troub
Contents Hazardous Locations Standards APPENDIX B Cable and Connectors A-6 B-1 Connector Specifications B-1 10/100 Ports B-1 SFP Module Connectors B-2 Dual-Purpose Ports B-2 Console Port B-2 Alarm Port B-3 Cables and Adapters B-4 SFP Module Cables B-4 Cable Pinouts B-7 Console Port Adapter Pinouts APPENDIX C B-8 Configuring the Switch with the CLI-Based Setup Program C-1 Accessing the CLI Through the Console Port C-1 Removing the USB Mini-Type B Console Port Cover C-1 RJ-45 Console Port C-2 USB
Preface Audience This guide is for the networking or computer technician responsible for installing Cisco IE 2000 series switches. We assume that you are familiar with the concepts and terminology of Ethernet and local area networking. Purpose This guide documents the hardware features of the Cisco IE 2000 switches. It describes the physical and performance characteristics of each switch, explains how to install a switch, and provides troubleshooting information.
Chapter Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.
CH A P T E R 1 Product Overview This switch provides a rugged and secure switching infrastructure for harsh environments. It is suitable for industrial Ethernet applications, including factory automation, intelligent transportation systems (ITSs), substations, oil and gas installations, and other deployments in harsh environments.
Chapter 1 Product Overview Switch Models Switch Models Table 1-1 lists and describes the switch models.
Chapter 1 Product Overview Switch Models Table 1-1 Switch Descriptions (continued) Model Description Software Image Cisco IE-2000-16TC-L 16 10/100BASE-T downlink ports, LAN Lite 2 Fast Ethernet dual-purpose uplink ports 2 100 Mb/s SFP module uplink slots Cisco IE-2000-16TC-B 16 10/100BASE-T downlink ports LAN Base 2 Fast Ethernet dual-purpose uplink ports 2 100 Mb/s SFP module uplink slots Cisco IE-2000-16TC-G-L 16 10/100BASE-T downlink ports LAN Lite 2 Gigabit Ethernet dual-purpose uplink p
Chapter 1 Product Overview Switch Models Table 1-1 Switch Descriptions (continued) Model Description Software Image Cisco IE-2000-16PTC-G-L 12 10/100BASE-T downlink ports LAN Lite 2 Gigabit Ethernet dual-purpose uplink ports 4 Power over Ethernet (PoE) ports Note Cisco IE-2000-16PTC-G-NX The four PoE ports can operate as PoE or as PoE+ if sufficient external power source is provided.
Chapter 1 Product Overview Front Panel Front Panel This section describes the front panel components. See Table 1-1. • 10/100BASE-T Ethernet ports • 10/100/1000 uplink ports (available on some models). • Dual-purpose ports (available on some models). • SFP module slots (available on some models). • PoE/PoE+ ports (available on some models). See Power over Ethernet Ports, page 1-9.
Chapter 1 Product Overview Front Panel 3 USB mini-Type B (console) port 8 Protective ground connection 4 RJ-45 console port 9 Flash memory card slot 5 Power connector DC-A Figure 1-2 Cisco IE-2000-8TC-L Front Panel 331545 3 1 4 5 ±12/ 24 0.5- /48 2.
Chapter 1 Product Overview Front Panel Cisco IE-2000-16TC-L Front Panel View 331544 Figure 1-3 3 1 4 5 ±12/ 24 0.5-3 /48 .
Chapter 1 Product Overview Front Panel Figure 1-4 Cisco IE-2000-16PTC-G-E Switch Front Panel View 3 1 4 5 ±12/ 0.5- 24/48 3.
Chapter 1 Product Overview Front Panel You can use the mdix auto interface configuration command in the command-line interface (CLI) to enable the automatic medium-dependent interface crossover (auto-MDIX) feature. When the autoMDIX feature is enabled, the switch detects the required cable type for copper Ethernet connections and configures the interfaces accordingly. For configuration information for this feature, see the switch software configuration guide or the switch command reference.
Chapter 1 Product Overview Front Panel By default, the switch selects the medium for each dual-purpose port (10/100BASE-T or SFP). When a link is achieved on one media type, the switch disables the other media type until the active link goes down. If links are active on both media, the SFP-module port has priority, but you can use the mediatype interface configuration command to manually designate the port as an RJ-45 port or an SFP port.
Chapter 1 Product Overview Front Panel Table 1-2 Supported SFP Models Type of SFP Module Model Commercial SFPs • GLC-SX-MM 32 to 158°F (0 to 70°C) • GLC-LH-SM • GLC-BX-U with DOM support • GLC-BX-D with DOM support • CWDM-SFP with DOM support • DWDM-SFP with DOM support Extended temperature SFPs • SFP-GE-S with DOM support 23 to 185°F (–5 to 85°C) • SFP-GE-L with DOM support • SFP-GE-Z with DOM support • GLC-SX-SMD • GLC-LH-SMD • GLC-EX-SMD For the most up-to-date list of s
Chapter 1 Product Overview Front Panel Power Connector 331209 Figure 1-5 The switch can operate with a single power source or with dual power sources. When both power sources are operational, the switch draws power from the DC source with the higher voltage. If one of the two power sources fail, the other continues to power the switch.
Chapter 1 Product Overview Front Panel Management Ports You can connect the switch to a PC running Microsoft Windows or to a terminal server through either the RJ-45 console port or the USB mini-Type B console port, also referred to as the USB-mini console port. These ports use the following connectors: • RJ-45 console port uses an RJ-45-to-DB-9 female cable. • USB-mini console port (5-pin connector) uses a USB Type A-to-5-pin mini-Type B cable.
Chapter 1 Product Overview Front Panel LEDs You can use the LEDs to monitor the switch status, activity, and performance. Figure 1-8 and Figure 19 show the front panel LEDs. Figure 1-8 LEDs on the Cisco IE 2000 Switch 2 3 4 5 7 ±12 /2 0.5- 4/48 3.0A ±12/ 24 0.5-3 /48 .
Chapter 1 Product Overview Front Panel Express Setup LED The Express Setup LED displays the express setup mode for the initial configuration. Table 1-3 lists the LED colors and their meanings. Table 1-3 Setup LED Color Setup Status Off (dark) Switch is configured as a managed switch. Solid green Switch is operating normally. Blinking green Switch is in initial setup, in recovery, or initial setup is incomplete.
Chapter 1 Product Overview Front Panel Alarm LEDs Table 1-6 and Table 1-7 list the alarm LED colors and their meanings. Table 1-6 Alarm OUT Status LED Color System Status Off Alarm OUT is not configured, or the switch is off. Green Alarm OUT is configured, no alarm detected. Blinking red Switch has detected a major alarm. Red Switch has detected a minor alarm. Table 1-7 Alarm IN1 and IN2 Status LEDs Color System Status Off Alarm IN1 or IN2 not configured.
Chapter 1 Product Overview Front Panel Port Status LEDs Each 10/100BASE-T downlink port, 10/100BASE-T uplink port, 10/100/1000BASE-T uplink port, dual-purpose uplink port, and SFP Module uplink slot has a port status LED, also called a port LED, as shown in Figure 1-8 and Figure 1-9. Table 1-9 displays LED information about the switch and the individual ports. Table 1-9 Port Status LEDs Color System Status Off No link. Solid green Link present. Blinking green Activity.
Chapter 1 Product Overview Front Panel Dual-Purpose Port LEDs Figure 1-9 shows the LEDs on a dual-purpose port. You can configure each port as either a 10/100/1000BASE-T port through the RJ-45 connector or as an SFP module, but not both at the same time. The LEDs show how the port is being used (Ethernet or SFP module). The LED colors have the same meanings as described in Table 1-9. Dual-Purpose Port LEDs 332704 Figure 1-9 ±12/ 24 0.5-3 /48 .
Chapter 1 Product Overview Front Panel PoE Status LED The PoE STATUS LED is located on the front panel of the IE 2000 switch models that are equipped with PoE ports.The LED displays the functionality and status of the PoE ports. The LED colors and meanings are listed in Table 1-10. Table 1-10 PoE Status LED Colors and Meanings Color PoE Status Off PoE is off.
Chapter 1 Product Overview Front Panel Figure 1-10 Flash Memory Card Slot 331548 ±12/ 24 0.5-3 /48 .0A 16T C Note The replacement SD card part number is SD-IE-1GB.
Chapter 1 Product Overview Rear Panel Rear Panel The rear panel of the switch has a latch for installation on a DIN rail. See Figure 1-11. The latch is spring-loaded to move down to position the switch over a DIN rail and return to the original position to secure the switch to a DIN rail.
Chapter 1 Product Overview Network Configurations • Cisco IOS CLI The switch CLI is based on Cisco IOS software and is enhanced to support desktop-switching features. You can fully configure and monitor the switch. You can access the CLI either by connecting your management station directly to the switch management port, or a console port, or by using Telnet from a remote management station. See the switch command reference on Cisco.com for more information. • Cisco Prime LAN Management Solution 4.
CH A P T E R 2 Switch Installation This chapter describes how to install your switch, verify the boot fast, and connect the switch to other devices. It also includes information specifically for installations in hazardous environments.
Chapter 2 Switch Installation Preparing for Installation Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001 Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. Statement 1003 Warning Read the installation instructions before you connect the system to its power source. Statement 1004 Warning This unit is intended for installation in restricted access areas.
Chapter 2 Switch Installation Preparing for Installation Caution Airflow around the switch must be unrestricted. To prevent the switch from overheating, there must be the following minimum clearances: – Top and bottom: 2.0 in. (50.8 mm) – Sides: 2.0 in. (50.8 mm) – Front: 2.0 in. (50.
Chapter 2 Switch Installation Preparing for Installation Warning Do not connect or disconnect cables to the ports while power is applied to the switch or any device on the network because an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed from the switch and cannot be accidentally be turned on, or verify that the area is nonhazardous before proceeding.
Chapter 2 Switch Installation Preparing for Installation North American Hazardous Location Approval The following information applies when operating this equipment in hazardous locations: English: Français: Products marked "Class I, Div 2, GP A, B, C, D" are suitable for use in Class I Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous locations only. Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code.
Chapter 2 Switch Installation Preparing for Installation • This equipment is considered Group 1, Class A industrial equipment, according to IEC/CISPR Publication 11. Without appropriate precautions, there may be potential difficulties ensuring electromagnetic compatibility in other environments due to conducted as well as radiated disturbance. • This equipment is supplied as open-type equipment.
Chapter 2 Switch Installation Installing or Removing the Flash Memory Card (Optional) • Airflow around the switch must be unrestricted. To prevent the switch from overheating, you must have the following minimum clearances: – Top and bottom: 2.0 in. (50.8 mm) – Sides: 2.0 in. (50.8 mm) – Front: 2.0 in. (50.8 mm) • Temperature surrounding the unit does not exceed 140°F (60°C).
Chapter 2 Switch Installation Installing or Removing the Flash Memory Card (Optional) To install or replace the flash memory card, follow these steps: Step 1 On the front of the switch, locate the door that protects the flash memory card slot. Loosen the captive screw at the top of the door using a Phillips screwdriver to open the door. See Figure 2-1. Figure 2-1 Installing the Flash Memory Card in the Switch 331548 ±12/ 24 0.5-3 /48 .
Chapter 2 Switch Installation Connecting to a Console Port Figure 2-2 Removing the Flash Memory Card from the Switch 331949 ±12/ 24 0.5-3 /48 .0A 16T C Step 2 Step 3 Install or remove the card: • To install a card, slide it into the slot, and press it in until it clicks in place. The card is keyed so that you cannot insert it the wrong way. • To remove the card, push it in until it releases for it to pop out. Place it in an antistatic bag to protect it from static discharge.
Chapter 2 Switch Installation Connecting to a Console Port RJ-45 Console Port Step 1 Connect the RJ-45-to-DB-9 adapter cable to the 9-pin serial port on the PC. See Figure 2-3. Connect the other end of the cable to the switch console port. Step 2 Start the terminal-emulation program on the PC or the terminal. The program, frequently a PC application such as HyperTerminal or PuTTy, makes communication between the switch and your PC or terminal possible.
Chapter 2 Switch Installation Connecting to a Console Port USB Mini-Type B Console Port Step 1 Step 2 If you are connecting the switch USB-mini console port to a Windows-based PC for the first time, install a USB driver.
Chapter 2 Switch Installation Connecting to a Console Port Step 3 Connect a USB cable to the PC USB port. Connect the other end of the cable to the switch mini-B (5-pin connector) USB-mini console port. See Figure 2-5. Figure 2-5 Connecting the USB-Mini Console Cable 2 331554 1 ±12/ 24 0.5-3 /48 .0A 1 16T C 2 3 Step 4 1 USB-mini console port 2 USB cable 3 USB port on the PC Identify the COM port assigned to the USB-mini console port: a. Choose Start > Control Panel > Systems. b.
Chapter 2 Switch Installation Connecting to Power Step 7 Configure the baud rate and character format of the PC or terminal to match the console port characteristics: • 9600 baud • 8 data bits • 1 stop bit • No parity • None (flow control) Step 8 Connect power to the switch as described in Connecting to Power, page 2-13. Step 9 When the PC or terminal displays the bootloader sequence, press Enter to display the setup prompt.
Chapter 2 Switch Installation Connecting to Power Table 2-1 Supported Power Supplies Dimensions 5.9 in H x 2.1 in. W x 4.9 in. D 5.9 in. H x 2.1 in. W x 4.9 in. D 5.8 in. H x 2 in. W x 4.4 in. D 5.8 in. H x 2 in. W x 4.4 in. D Attachable? Non-attachable Non-attachable Attachable unit Attachable unit 1 Designed for PoE Powers the switch. Designed for PoE modules, can be used to modules, can be used to Cannot be used to power the switch. power the switch.
Chapter 2 Switch Installation Connecting to Power Caution Use at least a 4 mm2 conductor to connect to the external grounding screw. The ground lug is not supplied with the switch.
Chapter 2 Switch Installation Connecting to Power Installing the Ground-Lug Screw (Single Ring Terminal) 331951 Figure 2-7 ±12/ 24 0.5-3 /48 .
Chapter 2 Switch Installation Connecting to Power Installing the Ground-Lug Screws (Two Single Ring Terminals) 331555 Figure 2-8 ±12/ 24 0.5-3 /48 .0A 16T C 1 1 Step 7 Ground cable Attach the other end of the ground wire to a grounded bare metal surface, such as a ground bus, a grounded DIN rail, or a grounded bare rack.
Chapter 2 Switch Installation Connecting to Power Note This section does not apply to PWR-IE50W-AC-IEC, which has pluggable IEC connector. Connecting the AC Power Source to the Power Converter Caution AC power sources must be dedicated AC branch circuits. Each branch circuit must be protected by a dedicated two-pole circuit breaker. Caution Do not turn on AC power until the wiring is secured. Step 1 Remove the plastic cover from the input power terminals and set it aside.
Chapter 2 Switch Installation Connecting to Power Step 4 Insert the line and neutral wire leads into the terminal block line and neutral connections. See Figure 2-9, items 2 and 3. Make sure that you cannot see any wire lead. Ensure that only wire with insulation extends from the connectors. Step 5 Tighten the line and neutral terminal block screws. Note Torque to 8 in.-lb, not to exceed 10 in-lb. Step 6 Replace the plastic cover over the terminal block.
Chapter 2 Switch Installation Connecting to Power Figure 2-10 AC/DC Power Input Terminal Block Wire Connections to a DC Source 1 347819 2 3 1 Earth ground wire connection 2 Return wire connection (to DC return) 3 Positive DC connection Warning An exposed wire lead from a DC-input power source can conduct harmful levels of electricity. Be sure that no exposed portion of the DC-input power source wire extends from the power and relay connector.
Chapter 2 Switch Installation Connecting to Power Warning A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Statement 1022 Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 3A. Statement 1005 Warning Installation of the equipment must comply with local and national electrical codes.
Chapter 2 Switch Installation Connecting to Power Table 2-2 DC-A and DC-B Power Connector Labels Label Connection + Positive DC power connection – Return DC power connection The switch panel labels can be seen in Figure 1-1, Figure 1-2, or Figure 1-3. Step 3 Measure two strands of twisted-pair copper wire (18-to-20 AWG) long enough to connect to the DC power source.
Chapter 2 Switch Installation Connecting to Power Step 6 On the power connector, insert the exposed part of the positive wire into the connection labeled “+” and the exposed part of the return wire into the connection labeled “–”. See Figure 2-14. Make sure that you cannot see any wire lead. Only wire with insulation should extend from the connector. Warning An exposed wire lead from a DC-input power source can conduct harmful levels of electricity.
Chapter 2 Switch Installation Connecting to Power Figure 2-15 Torquing the Power Connector Captive Screws 332022 1 1 Step 8 Power connector captive screws Connect the other end of the positive wire to the positive terminal on the DC power source, and connect the other end of the return wire to the return terminal on the DC power source. When you are testing the switch, one power connection is sufficient.
Chapter 2 Switch Installation Connecting to Power Figure 2-16 Completed DC Power Connections on the Power Connectors 2 3 4 332023 1 1 Power source A positive connection 3 Power source B positive connection 2 Power source A return connection 4 Power source B return connection If your power source is –48 VDC, this table describes the your wiring connections for Figure 2-16.
Chapter 2 Switch Installation Connecting to Power Attaching the Power Connectors to the Switch 331213 Figure 2-17 2 ±12/ 24 0.5-3 /48 .
Chapter 2 Switch Installation Connecting to Power Connecting the Power Connectors to the Switch 331214 Figure 2-18 ±12/ 24 0.5-3 /48 .0A 16T C 1 ±12/ 24 0.5- /48 3.0A 1 Step 2 DC-A power connector upper captive screw Use a ratcheting torque flathead screwdriver to tighten the captive screws on the sides of the power connectors. When you are testing the switch, one power source is sufficient.
Chapter 2 Switch Installation Connecting to Power Connecting Power to the Switch PoE DC-Input (Optional) This procedure is applicable only to the IE 2000 switch models that are PoE capable. If you have a PoE capable IE 2000 switch and do not plan on using PoE, you do not need to attach power to the PoE DC-input connector; the switch can operate without the connection being made. The following example shows how a second power supply is connected to the switch to support PoE.
Chapter 2 Switch Installation Connecting to Power To attach source DC to the PoE DC-input connector, follow these steps: Step 1 Verify that power is off to the DC circuit that you are going to attach to the switch PoE DC-input connector. This can be either of the two power supplies (AC-input or DC-input) or site source DC.
Chapter 2 Switch Installation Connecting to Power Step 7 Use a ratcheting torque flathead screwdriver to tighten the power connector captive screws (above the installed wire leads) to 2 in-lb (0.23 N-m). 332022 1 1—Power connector captive screws Step 8 Connect the other end of the positive wire to the positive terminal on the DC power source, and connect the other end of the return wire to the return terminal on the DC power source.
Chapter 2 Switch Installation Installing the Switch Verifying Boot Fast When you power on the switch, it automatically begins a boot fast sequence. The System LED blinks green as the Cisco IOS software image loads. If the boot fast sequence fails, the System LED turns red. Note Boot fast failures are usually fatal. Call Cisco TAC immediately if your switch does not complete boot fast successfully. See the “Obtaining Documentation, Obtaining Support, and Security Guidelines” section on page -viii.
Chapter 2 Switch Installation Installing the Switch Caution To prevent the switch from overheating, ensure these minimum clearances: – Top and bottom: 2.0 in. (50.8 mm) – Exposed side (not connected to the module): 2.0 in. (50.8 mm) – Front: 2.0 in. (50.8 mm) Installing the Switch on a DIN Rail The switch ships with a spring-loaded latch on the rear panel for a mounting on a DIN rail. You can install the switch as a standalone device on the DIN rail or with the expansion modules already connected.
Chapter 2 Switch Installation Installing the Switch Step 3 Push the switch toward the DIN rail to cause the spring-loaded latch at the bottom rear of the switch to move down, and snap into place. After the switch is mounted on the DIN rail, connect the power and alarm wires, as described in the “Connecting Alarm Circuits” section on page 2-34. For configuration instructions about the CLI setup program, see the Appendix C, “Configuring the Switch with the CLI-Based Setup Program.
Chapter 2 Switch Installation Connecting Alarm Circuits Releasing the Spring-Loaded Latch from the DIN Rail 331953 Figure 2-20 1 1 Step 4 Push latch down Remove the switch from the DIN rail. Connecting Alarm Circuits After the switch is installed, you are ready to connect the DC power and alarm connections.
Chapter 2 Switch Installation Connecting Alarm Circuits Wiring the External Alarms The switch has two alarm input and one alarm output relay circuits for external alarms. The alarm input circuits are designed to sense if the alarm input is open or closed relative to the alarm input reference pin. Each alarm input can be configured as an open or closed contact. The alarm output relay circuit has a normally open and a normally closed contact.
Chapter 2 Switch Installation Connecting Alarm Circuits Removing the Alarm Connector 332048 Figure 2-21 ±12/ 24 0.5-3 /48 .0A 16T C 1 1 Alarm connector Step 2 Measure two strands of twisted-pair wire (18-to-20 AWG) long enough to connect to the external alarm device. Choose between setting up an external alarm input or output circuit. Step 3 Use a wire stripper to remove the casing from both ends of each wire to 0.25 inch (6.3 mm) ± 0.02 inch (0.5 mm). Do not strip more than 0.27 inch (6.
Chapter 2 Switch Installation Connecting Alarm Circuits Figure 2-22 Inserting Wires into the Alarm Connector (Alarm Input Circuit) 1 332225 2 1 Step 5 Caution 2 IN1 - External device connection 1 REF - External device connection 2 Use a ratcheting torque flathead screwdriver to tighten the alarm connector captive screw (above the installed wire leads) to 2 in-lb (0.23 N-m). (See Figure 2-23.) Do not over-torque the power and alarm connectors’ captive screws.
Chapter 2 Switch Installation Connecting Alarm Circuits Step 6 Repeat Step 2 through Step 5 to insert the input and output wires of one additional external alarm device into the alarm connector. Figure 2-24 shows the completed wiring for two external alarm devices. The first alarm device circuit is wired as an alarm input circuit; the IN1 and REF connections complete the circuit.
Chapter 2 Switch Installation Connecting Destination Ports To attach the alarm connector to the front panel of the switch, follow these steps: Step 1 Insert the alarm connector into the receptacle on the switch front panel. See Figure 2-25. Connecting the Alarm Connector to the Switch 331215 Figure 2-25 ±12/ 24 0.5-3 /48 .0A 16T C 1 1 Step 2 Alarm connector upper captive screw Use a ratcheting torque flathead screwdriver to tighten the captive screws on the sides of the alarm connector.
Chapter 2 Switch Installation Connecting Destination Ports Connecting to 10/100 and 10/100/1000 Ports The switch 10/100/1000 ports automatically configure themselves to operate at the speed of attached devices. If the attached ports do not support autonegotiation, you can explicitly set the speed and duplex parameters. Connecting devices that do not autonegotiate or that have their speed and duplex parameters manually set can reduce performance or result in no linkage.
Chapter 2 Switch Installation Connecting Destination Ports Connecting to an Ethernet Port 331558 Figure 2-26 ±12/ 24 0.5-3 /48 .0A 1 16T C 2 Step 2 1 10/100 port 2 10/100 or 10/100/100 port (depending on model) Connect the other end of the cable to an RJ-45 connector on the other device. The port LED turns on when both the switch and the connected device have established a link. The port LED is amber while Spanning Tree Protocol (STP) discovers the topology and searches for loops.
Chapter 2 Switch Installation Connecting Destination Ports Installing and Removing SFP Modules These sections describe how to install and remove SFP modules. SFP modules are inserted into SFP module slots on the front of the switch. These field-replaceable modules provide the uplink optical interfaces, send (TX) and receive (RX). You can use any combination of rugged SFP modules. See the release notes on Cisco.com for the list of supported modules.
Chapter 2 Switch Installation Connecting Destination Ports Step 2 Find the send (TX) and receive (RX) markings that identify the correct side of the SFP module. On some SFP modules, the send and receive (TX and RX) markings might be replaced by arrows that show the direction of the connection, either send or receive (TX or RX). Step 3 Align the SFP module sideways in front of the slot opening.
Chapter 2 Switch Installation Connecting Destination Ports Step 4 Unlock and remove the SFP module. If the module has a bale-clasp latch, pull the bale out and down to eject the module. If the bale-clasp latch is obstructed and you cannot use your index finger to open it, use a small, flat-blade screwdriver or other long, narrow instrument to open the bale-clasp latch. See Figure 2-29. Opening a Bale-Clasp Latch on an SFP Module Using a Flat-Blade Screwdriver 331560 Figure 2-29 ±12/2 0.5-3.
Chapter 2 Switch Installation Connecting Destination Ports Warning Do not connect or disconnect cables to the ports while power is applied to the switch or any device on the network because an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed from the switch and cannot be accidentally be turned on, or verify that the area is nonhazardous before proceeding.
Chapter 2 Switch Installation Connecting Destination Ports Step 3 Insert the other cable end into a fiber-optic receptacle on a target device. Step 4 Observe the port status LED: Step 5 • The LED turns green when the switch and the target device have an established link. • The LED turns amber while the STP discovers the network topology and searches for loops. This process takes about 30 seconds, and then the port LED turns green.
Chapter 2 Switch Installation Verifying Switch Operation Connecting to a Dual-Purpose Port 331562 Figure 2-31 1 ±12/ 24 0.5-3 /48 .0A 16T C 2 1 Step 2 LC connector (optical) 2 RJ-45 connector (copper) Connect the other end of the cable to the other device. By default, the switch detects whether an RJ-45 connector or SFP module is connected to a dual-purpose port and configures the port accordingly.
Chapter 2 Switch Installation Where to Go Next • Start the Cisco Network Assistant application, which is described in the Getting Started with Cisco Network Assistant guide. Using the GUI, you can configure and monitor a switch cluster or an individual switch. • Use the CLI to configure the switch as an individual switch from the console. See the Command Reference on Cisco.com for information about using the CLI. • Start an SNMP application such as the CiscoView application.
CH A P T E R 3 Troubleshooting This chapter provides these topics for troubleshooting problems: • Diagnosing Problems, page 3-1 • How to Recover Passwords, page 3-5 • Finding the Switch Serial Number, page 3-6 Diagnosing Problems The switch LEDs provide troubleshooting information about the switch. They show boot fast failures, port-connectivity problems, and overall switch performance. You can also get statistics from Device Manager, the CLI, or an SNMP workstation.
Chapter 3 Troubleshooting Diagnosing Problems Switch LEDs Look at the port LEDs information when troubleshooting the switch. See the “LEDs” section on page 1-14 for a description of the LED colors and their meanings. Switch Connections Bad or Damaged Cable Always examine the cable for marginal damage or failure. A cable might be just good enough to connect at the physical layer, but it could corrupt packets as a result of subtle damage to the wiring or connectors.
Chapter 3 Troubleshooting Diagnosing Problems 10/100 and 10/100/1000 Port Connections If a port appears to malfunction: • Verify the status of all ports. See Table 1-9 on page 1-17 for descriptions of the LEDs and their meanings. • Use the show interfaces privileged EXEC command to see if the port is error-disabled, disabled, or shut down. Reenable the port if necessary. • Verify the cable type. See Appendix B, “Cable and Connectors”. SFP Module Use only Cisco SFP modules.
Chapter 3 Troubleshooting Diagnosing Problems Switch Performance Speed, Duplex, and Autonegotiation Port statistics that show a large amount of alignment errors, frame check sequence (FCS), or late-collisions errors, might mean a speed or duplex mismatch. A common issue occurs when duplex and speed settings are mismatched between two switches, between a switch and a router, or between the switch and a workstation or server.
Chapter 3 Troubleshooting Resetting the Switch Resetting the Switch These are reasons why you might want to reset the switch to the factory default settings: Note Caution • You installed the switch in your network and cannot connect to it because you assigned the wrong IP address. • You want to reset the password on the switch. Resetting the switch deletes the configuration and reboots the switch.
Chapter 3 Troubleshooting Finding the Switch Serial Number Finding the Switch Serial Number If you contact Cisco Technical Assistance, you need to know the serial number of your switch. The serial number is on the compliance label on the right-hand side of the switch. See Figure 3-1. You can also use the show version privileged EXEC command to obtain the switch serial number.
A P P E N D I X A Technical Specifications This appendix provides the technical specification for the Cisco IE 2000 switches. Operating Temperature Specifications Table A-1 lists the operating temperatures for the Cisco IE 2000 switches in three different environments.
Appendix A Technical Specifications Technical Specifications Technical Specifications Table A-2 lists the technical specifications for the Cisco IE 2000 switches.
Appendix A Technical Specifications Technical Specifications Table A-2 Cisco IE 2000 Series Technical Specifications (continued) Power consumption1 6-port models—9.5 W (typical), 15 W (maximum) • Cisco IE-2000-4T-L • Cisco IE-2000-4T-B • Cisco IE-2000-4T-G-L • Cisco IE-2000-4T-G-B • Cisco IE-2000-4TS-L • Cisco IE-2000-4TS-B • Cisco IE-2000-4TS-G-L • Cisco IE-2000-4TS-G-B 10-port models—12.
Appendix A Technical Specifications Technical Specifications Table A-2 Cisco IE 2000 Series Technical Specifications (continued) Physical Dimensions Weight 6-port models—2.45 lbs (1.11 kg) • Cisco IE-2000-4T-L • Cisco IE-2000-4T-B • Cisco IE-2000-4T-G-L • Cisco IE-2000-4T-G-B • Cisco IE-2000-4TS-L • Cisco IE-2000-4TS-B • Cisco IE-2000-4TS-G-L • Cisco IE-2000-4TS-G-B • 10-port models—2.75 lbs (1.
Appendix A Technical Specifications Technical Specifications Table A-2 Cisco IE 2000 Series Technical Specifications (continued) Dimensions2 (H x W x D) 6-port models—5.10 x 2.95 x 4.29 in. (13.0 cm x 7.5 cm x 10.9 cm) • Cisco IE-2000-4T-L • Cisco IE-2000-4T-B • Cisco IE-2000-4T-G-L • Cisco IE-2000-4T-G-B • Cisco IE-2000-4TS-L • Cisco IE-2000-4TS-B • Cisco IE-2000-4TS-G-L • Cisco IE-2000-4TS-G-B 10-port models—5.1 x 3.6 x 4.29 in. (13.0 cm x 9.1 cm x 10.
Appendix A Technical Specifications Alarm Ratings Alarm Ratings Table A-3 lists the alarm ratings for the Cisco IE 2000 switches. Table A-3 Alarm Input and Output Ratings Alarm Ratings Specification Alarm input electrical specification No power required—open or closed state detected. Alarm output electrical specification 1.0 A @ 24 VDC or 0.5 A @ 48 VDC Hazardous Locations Standards Table A-4 lists the hazardous location standards for the Cisco IE 2000 switches.
A P P E N D I X B Cable and Connectors • Connector Specifications, page B-1 • Cables and Adapters, page B-4 Connector Specifications • 10/100 Ports, page B-1 • SFP Module Connectors, page B-2 • Dual-Purpose Ports, page B-2 • Alarm Port, page B-3 10/100 Ports The 10/100 Ethernet ports on the switches use RJ-45 connectors. Figure B-1 shows the pinouts.
Appendix B Cable and Connectors Connector Specifications SFP Module Connectors Figure B-2 shows a MT-RJ style connector that is used with the SFP Module slots. It is a fiber-optic cable connector. Fiber-Optic SFP Module LC Connector 58476 Figure B-2 Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments.
Appendix B Cable and Connectors Connector Specifications The USB console port uses a USB Type A to 5-pin mini-Type B cable, shown in Figure B-5. The USB Type A-to-USB mini-Type B cable is not supplied. You can order an accessory kit (part number 800-33434) that contains this cable. USB Type A-to-USB 5-Pin Mini-Type B Cable 253405 Figure B-5 The RJ-45 console port uses an 8-pin RJ-45 connector (See Table B-3 and Table B-4.
Appendix B Cable and Connectors Cables and Adapters Cables and Adapters • SFP Module Cables, page B-4 • Cable Pinouts, page B-7 • Console Port Adapter Pinouts, page B-8 SFP Module Cables Each port must match the wave-length specifications on each end of the cable, and for reliable communications, the cable must not exceed the allowable length. Note The maximum operating temperature of the switch varies depending on the type of SFP module that you use.
Appendix B Cable and Connectors Cables and Adapters Table B-2 Fiber-Optic SFP Module Port Cabling Specifications Type of SFP Module Wavelength (nanometers) Fiber Type Core Modal Size/Cladding Bandwidth Size (micron) (MHz/km)1 Cable Distance Industrial and Rugged SFPs 1000BASE-SX (GLC-SX-MM-RGD) 850 MMF 62.5/125 62.5/125 50/125 50/125 160 200 400 500 722 feet (220 m) 902 feet (275 m) 1640 feet (500 m) 1804 feet (550 m) 1000BASE-LX/LH (GLC-LX-SM-RGD) 1310 MMF SMF 62.5 50.0 50.0 G.
Appendix B Cable and Connectors Cables and Adapters Table B-2 Fiber-Optic SFP Module Port Cabling Specifications (continued) Type of SFP Module Wavelength (nanometers) Fiber Type Core Modal Size/Cladding Bandwidth Size (micron) (MHz/km)1 Cable Distance Extended temperature SFPs 100BASE-LX/LH (SFP-GE-L) 1300 MMF or SMF 62.2 50 50 9/10 500 400 500 — 1804 feet (550 m) 1804 feet (550 m) 1804 feet (550 m) 6.2 miles (10 km) 100BASE-SX (SFP-GE-S) 850 MMF 62.5 62.5 50.0 50.
Appendix B Cable and Connectors Cables and Adapters Cable Pinouts Two Twisted-Pair Straight-Through Cable Schematic for 10/100 Ports Switch Router or PC 3 TD+ 6 TD– 3 RD+ 6 RD– 1 RD+ 2 RD– 1 TD+ 2 TD– Two Twisted-Pair Crossover Cable Schematic for 10/100 Ports Switch Switch 3 TD+ 6 TD– 3 TD+ 6 TD– 1 RD+ 2 RD– 1 RD+ 2 RD– Four Twisted-Pair Straight-Through Cable Schematic for 1000BASE-T Ports Switch Router or PC 1 TP0+ 1 TP0+ 2 TP0- 2 TP0- 3 TP1+ 3 TP1+ 6 TP1- 6 TP1- 4 TP2+ 4 TP2+
Appendix B Cable and Connectors Cables and Adapters Four Twisted-Pair Crossover Cable Schematics for 1000BASE-T Ports Switch Switch 1 TP0+ 1 TP0+ 2 TP0- 2 TP0- 3 TP1+ 3 TP1+ 6 TP1- 6 TP1- 4 TP2+ 4 TP2+ 5 TP2- 5 TP2- 7 TP3+ 7 TP3+ 8 TP3- 8 TP3- 65274 Figure B-9 To identify a crossover cable, hold the cable ends side-by-side, with the tab at the back. The wire connected to pin 1 on the left end should be the same color as the wire connected to pin 3 on the right end.
Appendix B Cable and Connectors Cables and Adapters Table B-3 lists the pinouts for the console port, the RJ-45-to-DB-9 adapter cable, and the console device.
Appendix B Cable and Connectors Cables and Adapters Cisco IE 2000 Switch Hardware Installation Guide B-10 OL-25818-04
A P P E N D I X C Configuring the Switch with the CLI-Based Setup Program This appendix provides a command-line interface (CLI)-based setup procedure for a switch. For information about setting up the switch by using Express Setup, see the Cisco IE 2000 Switch Getting Started Guide. Before connecting the switch to a power source, review the safety warnings in Warnings, page 2-1 For installation procedures, see Chapter 2, “Switch Installation.
Appendix C Configuring the Switch with the CLI-Based Setup Program Accessing the CLI Through the Console Port Removing the USB Mini-Type B Console Port Cover 332703 Figure C-1 ±12/ 24 0.5-3 /48 .0A 16T C RJ-45 Console Port Step 1 Connect the RJ-45-to-DB-9 adapter cable to the 9-pin serial port on the PC. Connect the other end of the cable to the switch console port. Step 2 Start the terminal-emulation program on the PC or the terminal.
Appendix C Configuring the Switch with the CLI-Based Setup Program Accessing the CLI Through the Console Port Figure C-2 Connecting the Console Cable 331563 1 ±12/2 0.5-3.
Appendix C Configuring the Switch with the CLI-Based Setup Program Accessing the CLI Through the Console Port USB Mini-Type B Console Port Step 1 If you are connecting the switch USB-mini console port to a Windows-based PC for the first time, install a USB driver. See Figure C-3 and the following sections for more information.
Appendix C Configuring the Switch with the CLI-Based Setup Program Accessing the CLI Through the Console Port a. Choose Start > Control Panel > Systems. b. Click the Hardware tab and choose Device Manager. Expand the Ports section. The assigned COM port appears in parenthesis at the end of the line with this entry: Cisco USB System Management Console. Step 4 Start the terminal-emulation program on the PC or the terminal.
Appendix C Configuring the Switch with the CLI-Based Setup Program Accessing the CLI Through the Console Port Step 5 Connect the USB cable to the PC and the switch console port. The USB console port LED turns green, and the Found New Hardware Wizard appears. Follow the instructions to complete the driver installation. Installing the Cisco Microsoft Windows 2000 USB Driver Step 1 Obtain the file Cisco_usbconsole_driver.zip from the Cisco.com web site and unzip it.
Appendix C Configuring the Switch with the CLI-Based Setup Program Accessing the CLI Through the Console Port Uninstalling the Cisco Microsoft Windows USB Driver • Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver • Uninstalling the Cisco Microsoft Windows Vista and Windows 7 USB Driver Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver Use the Windows Add or Remove Programs utility or the setup.exe file.
Appendix C Configuring the Switch with the CLI-Based Setup Program Entering the Initial Configuration Information Note Step 5 If a User Account Control warning appears, click Allow - I trust this program to proceed. When the InstallShield Wizard Completed window appears, click Finish. Entering the Initial Configuration Information To set up the switch, you need to complete the setup program, which runs automatically after the switch is powered on.
Appendix C Configuring the Switch with the CLI-Based Setup Program Entering the Initial Configuration Information Step 3 Enter an enable secret password, and press Return. The password can be from 1 to 25 alphanumeric characters, can start with a number, is case sensitive, allows spaces, but ignores leading spaces. The secret password is encrypted, and the enable password is in plain text. Enter enable secret: secret_password Step 4 Enter an enable password, and press Return.
Appendix C Configuring the Switch with the CLI-Based Setup Program Entering the Initial Configuration Information interface FastEthernet1/1 ! interface FastEthernet1/2 ! interface FastEthernet1/3 ! ...(output abbreviated) ! interface GigabitEthernet1/1 ! interface GigabitEthernet1/2 ! end Step 10 These choices appear: [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit.