7 August 2003 C H A P T E R 1 Cisco ONS 15530 Overview The Cisco ONS 15530 is a modular and scalable optical switching and aggregation platform designed to supplement the Cisco ONS 15540 ESP. With the Cisco ONS 15530, users can take advantage of the availability of dark fiber to build a common infrastructure that supports data, SAN (storage area network), and TDM (time-division multiplexing) traffic.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Chassis 7 August 2003 modules, line cards, and 2.5-G transponder trunk line cards. Slot 0 holds two half height optical OADM modules. Slots 1 through 4 and slots 7 through 10 hold the line cards and transponder cards. Slots 5 and 6 hold the CPU switch modules. Power supplies are located on the right side of the chassis next to slot 10. Air inlet and fan tray assembly are located beneath the slots. Cable management is located beneath the slots.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Chassis 7 August 2003 Cisco ONS 15530-CHAS-E Chassis The dimensions of the Cisco ONS 15530 CHAS-E chassis are 14.4 x 17.3 x 10.1 inches (H x W x D) See Figure 1-2. Handles for lifting the chassis are located on the sides.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Chassis 7 August 2003 The air ramp baffle for the Cisco ONS 15530 CHAS-E chassis redirects the cooling air intake as shown in Figure 1-4. The air ramp baffle must be installed when installing the Cisco ONS 15530 CHAS-E type chassis.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Chassis 7 August Figure 1-4 2003 Cisco ONS 15530 CHAS-E Chassis Airflow (with Air Ramp Baffle Installed) Exhaust air Top Rear Front Bottom 77824 Fan assembly Air ramp baffle Ambient air intake Cisco ONS 15530 CHAS-N Chassis The dimensions of the Cisco ONS 15530 CHAS-N chassis are 14.4 x 15.7 x 10.1 inches (H x W x D). (See Figure 1-5.) Handles for lifting the chassis are located on the top.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Chassis 7 August Cisco ONS 15530 CHAS-N Chassis 77081 F ST AN AT U S Figure 1-5 2003 Cisco ONS 15530 Hardware Installation Guide 1-6 78-14228-02
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Chassis 7 August Cisco ONS 15530 CHAS-N Chassis Airflow Top Exhaust air Rear Front Ambient air intake Fan assembly Bottom 77668 Figure 1-6 2003 Fan Assembly The Cisco ONS 15530 fan assembly is located at the bottom of the chassis. The assembly contains six individual fans and a fan controller board (see Figure 1-8). The controller board monitors the status of each fan and reports the status to the CPU switch modules.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Chassis 7 August Fan Assembly LED 77796 Figure 1-7 2003 Fan assembly LED Table 1-1 Fan Assembly Status Fan Failure LED Status None Green Normal One Yellow Minor Two or more Red Major Cisco ONS 15530 Hardware Installation Guide 1-8 78-14228-02
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Chassis 7 August Figure 1-8 2003 Fan Assembly 77834 N US FA TAT S Power Supplies The Cisco ONS 15530 chassis supports redundant 120–240 VAC (see Figure 1-9) or –48 VDC (see Figure 1-10) power. The power supplies are located at the right of the chassis, next to the card slots (see Figure 1-1). Up to two power supplies can be installed for redundancy.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Chassis 7 August Figure 1-9 2003 120–240 VAC Power Supply FASTENERS MUST BE FULLY ENGAGED PRIOR TO OPERATING THE POWER SUPPLY FAIL GOOD ~ 77894 100-240V 8.0- 3.5A 50-60 HZ Figure 1-10 –48 VDC Power Supply FASTENERS MUST BE FULLY ENGAGED PRIOR TO OPERATING THE POWER SUPPLY FAIL GOOD 77893 -48 TO -60V 17/A See the “Powering Up the Shelf” section on page 2-47 for more information about the power supplies.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Backplane The Cisco ONS 15530 backplane implements all board-to-board signal interconnects and provides power distribution within the chassis. Connections are present for two power supplies and the fan assembly. The backplane contains a total of 12 slots; two half-height slots for the OADM modules, two full height slots for the CPU switch modules, and eight full height slots for line cards and transponder cards.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 CPU Switch Modules The Cisco ONS 15530 supports two CPU switch modules for redundancy, one in active mode and the other in hot-standby mode. CPU switch modules are installed in slot 5 and slot 6.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Figure 1-11 Cisco ONS 15530 CPU Switch Module ST AT U S 1 2 R ES ET 3 AC ST 4 TI V BY E AN D 5 C O FL MP AS AC H T 7 6 9 FF 11 10 T C U 12 H C IST LR TO FF 13 8 C A M IN MA IRT L JO O IC R AL R A R M CU TO HI S S N M E 15 14 LI N K 10 16 FD 0M X BP S 17 C O N 18 AU X 77664 15530-CPU Cisco ONS 15530 Hardware Installation Guide 78-14228-02 1-13
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August Callout 2003 Description Callout Description 1 Card status LED 10 HIST LED 2 Reset button 11 Cutoff LED 3 Standby LED 12 HIST CLR LED 4 Active LED 13 NME port 5 CompactFlash card slot 14 Link LED 6 Minor alarm LED 15 100 Mbps LED 7 Major alarm LED 16 Full-duplex LED 8 Critical alarm LED 17 Console port 9 Cutoff LED 18 Auxiliary port CPU Switch Module Ports, LEDs, and Switches Table 1-2 lists t
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August Table 1-2 2003 CPU Switch Module LEDs (continued) LED Status Description HIST CLR Yellow A system wide major or minor alarm has occurred. CUTOFF Red A major or minor alarm exists and the cutoff button has been pushed. FDX Green Module is running full-duplex. Off Module is running half-duplex. Green Module is running at 100 Mbps. Off Module is running at 10 Mbps. Green Link is up. Off Link is down.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Connector Ports The front panel on the CPU switch module contains three ports with RJ-45 connectors (see Figure 1-11): • Network Management Ethernet port (NME)—This Ethernet port connects the CPU switch module to a 10/100BASE-T network management LAN. • Console port (CON)—This asynchronous EIA/TIA-232 serial port connects a terminal to the CPU switch module for local administrative access.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 OSC Modules and Carrier Motherboards The OSC (optical supervisory channel) module supports an optional out-of-band management channel for communicating between systems on the network. Using a 33rd wavelength (channel 0), the OSC allows control and management traffic to be carried without requiring a separate Ethernet connection to each Cisco ONS 15530 in the network.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 OSC Module LEDs Table 1-4 lists the LEDs on the OSC module faceplate, their default conditions, and what the conditions indicate. Table 1-4 OSC Module LEDs LED Status Description STATUS Green OSC module initialization process is complete. Yellow OSC module is in initialization process. TX Green Transmit laser is enabled. RX Green Light reception exists at wave OSC interface.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Figure 1-13 PSM 1 2 3 4 85519 5 1 Rx/Tx West ports 2 Rx/Tx East ports 3 East/West LEDs 4 East/West Optical Monitor ports 5 Common In/Out ports Cisco ONS 15530 Hardware Installation Guide 78-14228-02 1-19
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 PSM LEDs Table 1-5 lists the LEDs on the PSM faceplate, their default conditions, and what the conditions indicate. Table 1-5 PSM LEDs LED Status Description Green Software initialization is successful. Off Board failure. Transponder Line Cards The protocol-transparent and bit-rate transparent transponder line card converts a single client signal into an ITU wavelength, or channel.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Figure 1-14 Transponder Line Card LEDs (Nonsplitter) ST AT U S 1 3 T X T X R X 2 R X 4 5 7 T X T X 6 R X 8 77659 R X Cisco ONS 15530 Hardware Installation Guide 78-14228-02 1-21
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August Callout Description 2003 Callout Description 1 Card status LED 5 Client side transmit LED 2 ITU side port 6 Client side transmit port 3 ITU transmit LED 7 Client side receive LED 4 ITU receive LED 8 Client side receive port Cisco ONS 15530 Hardware Installation Guide 1-22 78-14228-02
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Figure 1-15 Transponder Line Card LEDs (Splitter) ST AT U S 1 2 4 5 6 8 10 W E S T T X 3 R X T X R X E A S T T X 7 R X T X R X T X 9 R X 11 W ITU TX W ITU RX E ITU TX E ITU RX 1310 TX 77660 1310 RX Cisco ONS 15530 Hardware Installation Guide 78-14228-02 1-23
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August Callout 2003 Description Callout Description 1 Card status LED 7 East side ITU port 2 West side ITU LED 8 Client side transmit LED 3 West side ITU port 9 Client side transmit port 4 ITU side transmit LED 10 Client side receive LED 5 ITU side receive LED 11 Client side receive port 6 East side ITU LED The transponder line cards are hot swappable, permitting in-service upgrades and replacement.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August Table 1-6 2003 Transponder Line Card LEDs (continued) LED Status Description RX (Trunk port) Green Light reception exists at the port. WEST1 Green Card is listening to the west side signal. TX (Client port) Green Port is up and transmit laser is enabled. RX (Client port) Green Light reception exists at the port. 1. This LED is only present on transponder line cards with splitter.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Figure 1-16 OADM Module 91400 1 Wide-Band Variable Optical Attenuator and Per-Band Optical Equalizer Modules The WB-VOA (wide-band variable optical attenuator) and PB-OE (per-band power equalizer) modules are half-width modules that allow the ONS 15530 to extend the internodal and ring circumference distances and number of nodes supported for point-to-point, hub ring, and mesh ring networks by equalizing power levels.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 The WB-VOA module and the PB-OE module are available in single and dual band versions. These modules are installed into a carrier motherboard. This motherboard is installed into and operates on the Cisco ONS 15530 chassis. The carrier motherboard can be installed in slots 1 to 4 or 7 to 10. All optical connectors are located on the front panel and the connectors are angled.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August Table 1-7 2003 Single WB-VOA Module LEDs LED Status Description PM1 Green Light reception exists at the port. STA Green Card is properly initialized.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August Table 1-8 2003 Dual WB-VOA Module LEDs LED Status Description PM2 Green Light reception exists at the port. PM1 Green Light reception exists at the port. STATUS Green Card is properly initialized.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August Table 1-9 2003 Single-Band PB-OE Module LED Status Description PM1 Green Light reception exists at the port. STA Green Card is properly initialized.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Table 1-10 Dual-Band PB-OE LEDs LED Status Description PM2 Green Light reception exists at the port. PM1 Green Light reception exists at the port. STATUS Green Card is properly initialized. ESCON Aggregation Cards The ESCON aggregation card is a 10-port card for ESCON (Enterprise Systems Connection) traffic.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Figure 1-21 Cisco ONS 15530 ESCON Aggregation Card ST AT U S 1 0 0 T X R X 2 T X 3 R X 4 1 T X R X 2 T X R X 3 T X R X 4 T X R X 5 T X R X 6 T X R X 7 T X R X 8 T X R X 9 15530-LCMB-0200 R X 77663 T X Cisco ONS 15530 Hardware Installation Guide 1-32 78-14228-02
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August Callout Description 2003 Callout Description 1 Card status LED 3 Port receive LED 2 Port transmit LED 4 Port number Table 1-11 describes the ESCON aggregation card LED status. Table 1-11 ESCON Aggregation Card LEDs LED Status Description STATUS Green Card is properly initialized. Blinking green Good system clock is present and card is out of reset state. Yellow System clock is not present.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August Note 2003 We strongly recommend configuring port pairs as FC only or GE only. Mixing FC and GE in a port pair increases the FC signal latency between nodes. The 8-port FC/GE aggregation card uses single-mode and multimode SFP optics for the client signals. There are no restrictions on populating the line card with SFPs. For example, you can mix a single-mode SFP optic with a multimode SFP optic in the same port pair.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Figure 1-22 8-Port FC/GE Aggregation Card ST AT U S 1 0 0 T X R X 2 T X 3 R X 4 1 T X R X 2 T X R X 3 T X R X 4 T X R X 5 T X R X 6 T X R X 7 T X R X 85440 15530FCGE-8P Cisco ONS 15530 Hardware Installation Guide 78-14228-02 1-35
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 1 Card status LED 2 Transmit Port status 3 Receive Port status 4 Port number Table 1-13 describes the LEDs on the 8-port FC/GE aggregation card. Table 1-13 8-Port FC/GE aggregation card LEDs LED Status Description STATUS Off No power to the board. Red Card is in reset or the LRC is not configured. Yellow Card is out of reset. Green Card is properly initialized.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Figure 1-23 2.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 1 Card status LED 5 Receive LED 2 West side port LED 6 East side port LED 3 West side port 7 East side port 4 Transmit LED Cisco ONS 15530 Hardware Installation Guide 1-38 78-14228-02
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Figure 1-24 2.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 1 Card status LED 2 Transmit LED 3 Receive LED 4 Transmit/Receive port Table 1-14 lists and describes the 2.5-Gbps ITU Trunk Card LEDs. Table 1-14 2.5-Gbps ITU Trunk Card LEDs LED Status Description STATUS Green Card is properly initialized. WEST Green Card is listening to the west side signal. TX Green Port is up and transmit laser is enabled. RX Green Light reception exists at the port.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Figure 1-25 10-Gbps ITU Trunk Card (Nonsplitter) ST AT U S 1 T X 3 R X 77661 4 2 R X T X Cisco ONS 15530 Hardware Installation Guide 78-14228-02 1-41
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 1 Card status LED 3 Transmit LED 2 ITU port 4 Receive LED Cisco ONS 15530 Hardware Installation Guide 1-42 78-14228-02
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Figure 1-26 10-Gbps ITU Trunk Card (Splitter) ST AT U S 1 2 4 5 6 W E S T T X T X 3 R X R X E A S T T X 7 R X W ITU TX W ITU RX 77662 E ITU TX E ITU RX Cisco ONS 15530 Hardware Installation Guide 78-14228-02 1-43
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 1 Card status LED 5 Receive LED 2 West side port LED 6 East side port LED 3 West side port 7 East side port 4 Transmit LED Table 1-15 describes the10-Gbps ITU trunk card LED status. Table 1-15 10-Gbps ITU Trunk Card LEDs LED Status Description STATUS Green Card is properly initialized. WEST Green Card is listening to the west side signal. TX Green Port is up and transmit laser is enabled.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 The Cisco ONS 15530 supports up to four 10-Gbps uplink cards for a total of four signals.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Figure 1-27 10-Gbps Uplink Card ST AT U S 1 3 4 T X T X 2 R X 5 R X 77665 15530-10GE-UPLINK Cisco ONS 15530 Hardware Installation Guide 1-46 78-14228-02
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Table 1-16 describes the 10-Gbps uplink line card LED status. Table 1-16 10-Gbps Uplink Line Card LEDs LED Status Description STATUS Green Card is properly initialized. TX Green Port is up and transmit laser is enabled. RX Green Light reception exists at the port.
Chapter 1 Cisco ONS 15530 Overview Cisco ONS 15530 Components 7 August 2003 Cisco ONS 15530 Hardware Installation Guide 1-48 78-14228-02