AL10 USER GUIDE ‐ Draft Rev2 USER GUIDE AlertMaster AL10 Home Alert System Clarity, a Division of Plantronics, Inc. 4289 Bonny Oaks Drive, Chattanooga, TN 37406 Tel: 800‐426‐3738 Fax: 800‐325‐8871 E‐mail: claritycs@plantronics.com Website: www.clarityproducts.com ©2010 Clarity, a Division of Plantronics, Inc. All rights reserved. AlertMaster, Clarity and AL10 are trademarks or registered trademarks of Plantronics, Inc. Rev.
AL10 USER GUIDE ‐ Draft Rev2 CONTENTS (TO BE LEFT EMPTY UNTIL FINAL VERSION IS CREATED; THIS PAGE SHOWS THE TABLE OF CONTENTS) 2|Page
AL10 USER GUIDE ‐ Draft Rev2 IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and persons including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Do not use this product near a bathtub, wash basin, kitchen sink or laundry tub, in a wet basement, near a swimming pool or anywhere else there is water. 4.
AL10 USER GUIDE ‐ Draft Rev2 ADDITIONAL SAFETY NOTES FOR CANADIAN USERS The following items are included as part of the CS‐03 Requirements. The standard connecting arrangement for the equipment is CA11A. This product meets the applicable Industry Canada technical specifications. NOTE: The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective operational and safety requirements.
AL10 USER GUIDE ‐ Draft Rev2 INTRODUCTION Thank you for selecting the exciting new AL10 from Clarity. It has been designed to meet the highest quality standards to provide you with years of convenient and trouble‐free service. Please read these operating instructions thoroughly before using your notification system. Keep this manual for future reference. You must save your sales receipt as proof of purchase in the event that you need warranty service.
AL10 USER GUIDE ‐ Draft Rev2 PACKAGE CHECKLIST Please make sure your AL10 package includes the items as shown below: 6|Page
AL10 USER GUIDE ‐ Draft Rev2 FEATURES IDENTIFICATION 7|Page
AL10 USER GUIDE ‐ Draft Rev2 INSTALLATION AND SET‐UP An ideal location for setting up the base unit is in the bedroom. Do not put any of the AL10 components on or next to metal surfaces, computers, television, microwaves, or other areas with electronic equipment that can cause interference to the wireless system. A. Base Unit B.
AL10 USER GUIDE ‐ Draft Rev2 C. Clock 1. Press the SET CLOCK (on the back of the unit) and the SET HOUR or SET MINUTE (both on the front of the unit) buttons simultaneously to change time setting. 2. Press the SET ALARM button (front of unit) to check the alarm setting. 3. Press SET ALARM and SET HOUR (or SET MINUTE) buttons simultaneously to change alarm clock setting. 4. Press ALARM ON/OFF button to turn alarm on or off.
AL10 USER GUIDE ‐ Draft Rev2 OPERATIONS A. MONITORING FUNCTIONS The console has six indicator lights for each of the alerting functions of the AL10. Some functions require an optional accessory to be purchased. Anytime the AL10 Notification System is activated by any function(s), the lamp and bed shaker will activate, then stop and reset after two minutes, or use the RESET / PAGE button on the top of the console to stop and reset it. The lamp flashes in different patterns for each function. 1.
AL10 USER GUIDE ‐ Draft Rev2 3. CLOCK/PAGING The clock indicator light and sidebar lights illuminate when the alarm clock is activated. The bed shaker will vibrate and the lamp will turn on for one second, off for two seconds, and repeat.
AL10 USER GUIDE ‐ Draft Rev2 Alarm/Snooze When the alarm clock activates, the bed shaker will vibrate and the lamp will flash for one hour, or until the SNOOZE or RESET/PAGE button is pushed. This stops the alarm clock and resets it for the same time on the next day. The “SNOOZE” time on the alarm is nine minutes. Paging When the RESET / PAGE button is pressed for just a moment, it activates the base unit and any remote receivers or personal signalers that are within an 80‐foot range.
AL10 USER GUIDE ‐ Draft Rev2 5. ALARM You must purchase the optional Audio Alarm Transmitter (Model AM‐AX) from Clarity to use this function. When a signal is received from the Audio Alarm Transmitter, the indicator light illuminates, and the lamp will turn on for one second, off for one second, and repeat.
AL10 USER GUIDE ‐ Draft Rev2 6. MOTION SENSOR LIGHT You must purchase the optional Motion Sensor (Model AM‐SX) from Clarity to use this function. When a signal is received from the Motion Sensor, the indicator light illuminates, and the lamp will turn on for one second, off for one second, on again for one second, off for two seconds, and repeat. B.
AL10 USER GUIDE ‐ Draft Rev2 D. Security Timer With this feature, the lamp connected to your AlertMaster system will go on automatically every evening and turn off later in the evening. You can use this to make it look like someone is home. The light will turn on and off at slightly different times each evening so it is not so obvious that a timer is being used. To activate this feature: 1. Press the TIMER ON / OFF button once.
AL10 USER GUIDE ‐ Draft Rev2 CHANNEL SETTINGS The AlertMaster System uses special radio signals to communicate between the console unit and all its accessories. For the accessories (Door Announcer, Baby Sound Monitor, Audio Alarm Transmitter and Motion Sensor) to activate the base unit, they all have to be on the same "channel." A "DIP switch" is used for channel selection. Your system and all the accessories have been preset in the factory to a standard channel setting.
AL10 USER GUIDE ‐ Draft Rev2 17 | P a g e
AL10 USER GUIDE ‐ Draft Rev2 TROUBLESHOOTING If any problem should occur during operation of your AlertMaster Notification System, review the "Symptom and Remedy" list below. Make sure no part of the AlertMaster system is on or near metal surfaces or electronic equipment. Should the difficulty persist, contact Clarity or your authorized dealer for assistance. Symptom Cause and Remedy Lamp control button doesn’t work Lamp is not turned on prior to plugging it into AlertMaster. Turn the lamp’s switch on.
AL10 USER GUIDE ‐ Draft Rev2 OPTIONAL ACCESSORIES The AlertMaster AL10 is designed to work with optional wireless remote receivers and transmitters, each sold separately. A. Remote Receiver (AL12) Plug the receiver into an AC outlet, and plug in a lamp and you’ll be notified wherever the receiver is placed ‐ kitchen, living room, garage, bathroom, etc. It operates up to 80 feet from the AlertMaster AL10 base console. B.
AL10 USER GUIDE ‐ Draft Rev2 REGULATORY COMPLIANCE Important Information for Customers PART 68 OF FCC RULES INFORMATION This AL10 Notification System complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
AL10 USER GUIDE ‐ Draft Rev2 If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this telephone equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. This telephone equipment is hearing aid compatible.
AL10 USER GUIDE ‐ Draft Rev2 INDUSTRY CANADA TECHNICAL SPECIFICATIONS This product meets the applicable Industry Canada technical specifications. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection.
AL10 USER GUIDE ‐ Draft Rev2 WARRANTY INFORMATION This warranty applies only to CLARITY products that are purchased and used in the United States, Canada or United Kingdom. CLARITY warrants the ALERTMASTER AL10 against any defect in materials or workmanship for the period of one year from the date of purchase. If your CLARITY product is defective and returned within 30 days of the date of purchase, your authorized Clarity dealer will replace it at no charge.
AL10 USER GUIDE ‐ Draft Rev2 CLARITY, a Division of Plantronics 4289 Bonny Oaks Drive • Chattanooga, TN 37406 Tel: 800‐426‐3738 • Fax: 800‐325‐8871 E‐mail: claritycs@plantronics.com • Website: www.clarityproducts.