Owner`s manual

Programmable Features
AvantGuard 4 comes from the factory with its features preprogrammed as noted in bold letters in the following tables. Some features
can be programmed by the installer or the user, others can only be programmed by the installer. The re are two tables provided which
define the user-programmable and installer-programmable features.
Using the CliffNet Wizard Pro Installation Software
CliffNet Wizard PRO provides an intuitive access to all installer and user-programmable features th rough a user-friendly, graphical
user interface and provides extensive diagnostic capabilities. See www.clifforddealer.com to download a free copy of the program.
Programming the User-Selectable Features
1.Write down the column (across) number and row (down) number of the feature(s) you wish to program.
2. Turn the ignition to the “ON” position or start the engine.
3.Enter the factory preset valet/programming code of “2” by pressing the PlainView 2 Switch’s ✱ button twice, then press the blank
button.
4.After entering the code, press and hold the ✱ for about 3 seconds until you hear one siren chirp and the LED turns on to
acknowledge program mode entry. The system is now in the “Feature Select” position for User-Program mable Features.
5.Select the feature column: Press the blank button the same number of times as the column number. Pa use. You will then hear the
same number of chirps as the column number you have selected, audibly confirming your selection.
6.Within five seconds, select the feature row: Press and release the ✱ button the same number of times as the feature’s row number.
You’ll hear a chirp each time you press the blank side to help you count.
7.If there is a NOTE for the selected feature, perform the actions noted.
8. Pause. You will hear either one or two chirps: Two chirps = ON, one chirp = OFF.
9.You can select another feature, or you can exit program mode:
a. To select another feature in that same column, repeat step 6 within the next five seconds (after fi ve seconds, three chirps
indicate that the system is now back in the “Feature Select” position).
b. To select a different feature column, repeat step 5.
c. To exit program mode, turn the ignition off (you’ll hear three chirps and the LED will turn off to indicate exit of program
mode), or wait 60 seconds and the system will automatically exit program mode.
User-Programmable Features
User-Programmable Features (1 Chirp = OFF, 2 Chirps = ON)
Fea ture
Select
Blank 1 Blank 2 Blank 3 Blank 4
✱ 1
AutoProgram New Master Remote
NOTE 1
Chirps
(Off/LoudChirps/QuietChirps)
(1 chirp/2 chirps/3 chirps)
AutoArming
(Off/On)
Arm/Disarm with
Secondary Remote
NOTE 7
✱ 2
Personalized Siren Sounds
NOTE 2
SilentNight
(On/Off)
AutoArm & Lock
(Off/On)
Trunk Release with
Secondary Remote
NOTE 8
✱ 3
Play Siren Sounds
(Always/Trigger Only)
(1 chirp/2 chirps)
Remote Valet Feature
(Off/On)
En try De lay
(Off /On)
Silent Arm/Disarm with
Secondary Remote
NOTE 8
✱ 4
Siren Duration
(30/60/90 Seconds)
(1 chirp/2 chirps/3 chirps)
AutoStart
(Both/Neither/Battery/Temperature )
(1 chirp/2 chirps/3 chirps/4 chirps)
FACT
(Off/On)
Timed Headlight Activation with
Secondary Remote
NOTE 8
✱ 5
AutoLock
(Off/Instant/RPM-Dependent)
(1 chirp/2 chirps/3 chirps)
BlackJax
(Off/On)
Headlight Duration
10 Seconds
NOTE 5
Remote Start with
Secondary Remote
NOTE 8
✱ 6
AutoUnlock
(Off/On)
Clear All Remotes
NOTE 4
NightVision
(Off/On/On without post-parking
illumination)
Window Rolldown/Venting
with Secondary Remote*
NOTE 8
✱ 7
Re set All to Fac tory Set tings
(ex cept re motes and valet code)
NOTE 3
Valet Code
SHOULD ONLY BE SET BY THE
VEHICLE OWNER
Night Vi sion Ac ti va tion
(Lighter/Twi light/Darker)
(1 chirp/2 chirps/3 chirps) NOTE 6
Remote Valet Mode
with Secondary Remote
NOTE 8
*Re quires op tional SmartWin dows 4
Avant Guard 4/699 17