Owner`s manual

n
NOTE 1:
o Press button 1 on the master remote, you will hear one chirp. Press button 1 again , you will hear two chirps.
o Auto Programming is for master remotes only. Companion remotes must be programmed via the column f our selections or via the
CliffNet Wizard Pro installation software.
nn
NOTE 2: When this feature is selected, siren sound 1 will play for five seconds. Press marked to turn the siren sound off, press blank to
activate the sound. Next, siren sound 2 will play for five seconds. Press marked to turn the sire n sound off, blank to activate it. The
system will cycle through all six siren sounds.
n
NOTE 3: You will hear two chirps when all features are reset.
n
NOTE 4: When you hear two chirps, all remote controls will have been erased from the system memory. You mus t now add the new
and/or existing remote controls to the system (i.e., AutoProgram each remote that will be used with the AvantGuard 4).
n
NOTE 5: Once this feature is selected, one chirp is provided to indicate that the timer has started. You can set this anywhere from
one second to four minutes. When the desired duration has been reached, press the blank side of the PlainView 2 switch. The system
responds with two chirps to confirm the new system timer duration.
n
NOTE 6: Regardless of the current NightVision setting, the system will always provide one confirmation chir p when this program feature
is accessed.
n
NOTE 7: Programs a companion remote control from this system or from another Clifford system that uses ACG -II technology to arm
or disarm the vehicle. For instance, to set button 13 of the other car’s master remote control to a rm/disarm the system, select column 4,
row 1, then transmit channel 13 from the remote you are programming. The system will respond with o ne chirp. Immediately transmit
channel 13 again. The system will respond with two chirps. Button 13 of the other vehicle’s remote will now arm/disarm the system.
n
NOTE 8: This feature can be programmed onto the remote control of another Clifford system that uses ACG-II technology, after that
remote has been programmed to arm/disarm this system. Select the row and column number, then transm it the unused button on the
other remote that you want to use to perform that function. The AvantGuard 4 will respond with the same number of chirps as the row
number. Please note that you must first set a button on the remote that will arm/disarm the system (column 4, row 1) before these others
will be accepted.
Installer-Programmable Features
To access the installer-programmable features, use the procedure defined in the User-Programmable s ection, but in step 4, hold and
press the ✱ side of the PlainView 2 Switch for 10 seconds. You will hear three confirmation chirps indicating that the system is in
installer-program mode.
Table of Installer-Programmable Features (1 chirp = OFF, 2 chirps = ON)
Fea ture
Select
Blank 1 Blank 2 Blank 3
✱ 1
Single /Double Lock Pulse
(1 chirp/2 chirps)
Accessory Output Timer
Duration
(10 seconds )
See NOTE 1
Door Ajar Warning /Delayed
Courtesy Lights
(1 chirp/2 chirps)
✱ 2
Single /Double Unlock Pulse
(1 chirp/2 chirps)
Auxiliary A Type
(Pulsed /Timed/Latched)
(1 chirp /2 chirps/3 chirps)
Auxiliary A Interlock
(On/Off)
✱ 3
Lock/Unlock Pulse
3 second/1 second
(1 chirp/2 chirps)
Auxiliary B Type
(Pulsed /Timed/Latched)
(1 chirp /2 chirps/3 chirps)
Auxiliary B Interlock
(On/Off)
✱ 4
AutoActivate Auxiliary C upon
Remote Arming
(On/Off)
Auxiliary C Type
(Pulsed/Timed/Latched)
(1 chirp/2 chirps/3 chirps)
Auxiliary C Interlock
(On/Off)
✱ 5
Program RPM
See
Mandatory RPM Programming
Diesel Engine/Gas Engine
(1 chirp/2 chirps)
See NOTE 2
Program Window RollUp or
optional SmartWindows 4
See NOTE 3
✱ 6
Aux il iary Si ren Out put
(Constant/Pulsed)
(1 chirp/2 chirps)
NOT USED NOT USED
18 Avant Guard 4/699