Congratulations Congratulations on the purchase of your state-of-the-art security and remote start system. Reading this Owner’s Guide prior to using your system will help maximize the use of your system and its many features. Please visit: www.clifford.com – For general and additional guide information. For any additional questions please contact your authorized Directed dealer or contact Directed at 1-800-753-0600. What you get Welcome to the best generation of security with remote start.
Important information Government Regulations and Safety information Read the Government Regulations and Warning! Safety First sections of this manual prior to operating this system. Warning! Failure to heed this information can result in death, personal injury or property damage and may also result in the illegal use of the system beyond its intended purpose. Your Warranty Your Responder LC system comes with a warranty.
Contents Getting Started.................................................................................................... 4 Charging the remote control:................................................................. 4 Keys to using this manual...................................................................... 5 Responder LC 2-Way........................................................................................... 6 Status Screen Icons ...........................................................
Main Menu ....................................................................................................... 24 Setup Remote menu:........................................................................... 24 Remote Start Info ............................................................................... 25 Runtime Alert..................................................................................... 26 Car 2 .........................................................................................
Remote and System Operations .......................................................................... 40 Passive Arming .................................................................................. 40 Auto Re-arming.................................................................................. 40 Valet Mode ....................................................................................... 41 Power Save.......................................................................................
Getting Started Your Responder LC remote is powered by an internal rechargeable battery that can only be serviced by an authorized Directed dealer. Due to transit and storage time prior to your purchase, the battery charge may have depleted. To ensure proper operation, check the battery level and connect the battery charger if not fully charged. See “Battery Information (Responder LC)” on page 49 and “Status Screen Icons” on page 8 for more information about the battery. Charging the remote control: 1. 2.
Keys to using this manual At a Glance Specific actions (in bold type) and style conventions are used consistently throughout this manual, they are as follows: s s s s s Press: implies pushing in and releasing a button. Hold: is used after Press actions when a button needs to be held in position for an extended period of time, typically several seconds. ARMED this style denotes the text which appears in the text field portion of the Display during operations described in the manual.
Responder LC 2-Way Internal Antenna Display Command Buttons 6 Function Button Mini-USB Port Feature Description Internal Antenna Used for transmitting and receiving information Display Status screen - the upper portion of the display contains status icons for the System, Siren, Alarm zones, Remote Start and Remote Control.
Control Center At a Glance Status LED Control button The Control Center, typically located on the upper part of the front windshield sends and receives commands or messages to and from your system. It consists of: s s s The In-vehicle system antenna, for 2 way communication. The Status LED, as a visual indicator of the system’s status. The Control button, for placing the system into Valet Mode* and to perform the Emergency Override** operation.
Status Screen Icons Status Screen Icons ALL 1 Text Field The table below describes all the status screen icons. Icon Description System Status Armed: The system is Armed, the alarm is enabled. Locked: The system is Locked in Valet, the alarm is disabled. Disarmed: The system is Disarmed, the alarm is disabled. Remote Start Siren Status Unlocked: The system is Unlocked in Valet, the alarm is disabled. 8 Siren is disabled for sensor triggers; remote is paged for all triggers (Sensor Silent Arm).
Icon Remote Start At a Glance + Description Smart Start is On; Remote Start is On. Note: When the icon is without an arrow head: Smart Start is On; Remote Start is Off.
Icon Description Bars indicate battery level is Full, ¾,½,¼ or Empty On while the remote control is transmitting a command On while the remote control is receiving a message Remote Control Status On with Out of Range fault tone to indicate the remote failed to receive a command confirmation Pager on: The remote will wake up to listen for messages Pager off: The remote will not wake up to listen for messages The remote will Vibrate when messages are received The remote will emit Beeps and Tones when messa
Using your System Commands and Confirmations Performing Commands Perform Basic commands by pressing one of the command buttons while in the Direct Access level. Direct access is available while the text field displays the Clock, Temperature or Runtime. Perform Advanced commands by first accessing one of the Function Levels and then pressing one of the command buttons while within a level. Function Levels are available when the text field displays LEVEL 1,2,3 or 4. Advanced command example: Silent Arm 1.
Responder LC Command table Level Direct Access Button x1 LEVEL 1 Arm/Lock Silent Arm (Panic) x2 LEVEL 2 x3 LEVEL 3 x4 LEVEL 4 Sensor Sensor Silent Full Silent Bypass Arm Arm Disarm/Unlock Silent Disarm Remote Valet Car Finder Remote Start Runtime Timer Start Smart Start Defogger AUX 4 Reset AUX Aux/Trunk AUX 1 AUX 2 AUX 3 Advance Level Temperature Runtime Alarm Change Car Check Remaining Report (3s), Enter programming (8s) Fault Condition Alerts If, when performing a
** Remote Start feature not available when the Remote Start status is incorrect upon receiving the command. (Example: Runtime reset command received when remote start is off) Refer to the notes included in the command descriptions that address these faults or go to “Remote Start Error” on page 39 for more details. Commands © 2011 Directed Electronics. All rights reserved.
Basic Commands (Direct Access) Arm Press and release 6:30 The alarm arms, doors lock (if connected), and the siren chirps and parking lights flash once. The ARMED text and beeps play to confirm and the System Status Icons update. If Valet mode* is On, the doors lock and the VALET text and tone play. Exit Valet mode to arm the alarm normally. If a trigger zone fault is detected the siren chirps once again and the Trigger Zone Fault report** plays.
AUX/Trunk Press and hold AUX Remote Start Press and release Activates (or if On, deactivates) the remote starter. The engine and parking lights turn On and the REMOTE START ON text and tones play, or the engine and parking lights turn Off and the REMOTE START OFF text and tones play to confirm, the Remote Start status icons update. The icon will display in the status screen and the text field will display the Runtime, Temperature or Clock as programmed.
Advanced Commands: (Level 1) Press and release the button 1 time. level 1 Silent Arm Press and release The alarm arms, doors lock (if connected), and the parking lights flash once. The SILENT ARMED text plays to confirm and the System Status icons update. Valet mode* or Trigger Zone Fault report** messages may be received. Silent Disarm Press and release The alarm disarms, doors unlock (if connected), and the parking lights flash twice.
Runtime Reset Press and release Note Remote Start must be On to use this feature. Temp Request Press and hold the button Requests the vehicle’s interior temperature and temporarily displays it via status screen icon and text field. * See “Remote and System Operations” on page 40 for details. ** See “Alarm Features” on page 30 for details. © 2011 Directed Electronics. All rights reserved.
Advanced Commands: (Level 2) Press and release the button 2 times. Sensor Bypass level 2 Press and release The parking lights flash each time this command is received to indicate the Sensor bypass type. 2 flashes indicates sensor Warn-away zones are bypassed. BYPASS WARN , 1 beep and 1 fault tone play to confirm. 3 flashes indicates sensor Warn-away and Full Trigger zones are bypassed. BYPASS FULL , 1 beep and 2 fault tone play to confirm.
Timer Start* Press and release Note System needs to be armed or Timer Start will not start the engine. Runtime Remaining Press and hold the button Requests the remaining Remote start runtime and temporarily displays it in the text field. Note Remote Start must be On to use this feature. * See “Advanced Start” on page 35 for more details. © 2011 Directed Electronics. All rights reserved. 19 Commands Activates (or if On, deactivates) Timer Start.
Advanced Commands: (Level 3) Press and release the button 3 times. level 3 Sensor Silent Arm* Press and release The alarm arms, doors lock, the siren chirps and parking lights flash 3 times. The SENSOR SILENT ARM text and beeps play to confirm and the System and Siren Status icons update. Car finder Press and release The siren emits one long chirp and the parking lights flash for 10 CAR FINDER seconds. The text and beeps play to confirm.
Smart Start** Press and release Note System needs to be armed or Smart Start will not start the engine. Alarm Report* Press and hold the button Requests a report of the most recent triggers and temporarily displays it in the text field. The report clears when the ignition is turned on. * See “Alarm Features” on page 30 for more details. ** See “Advanced Start” on page 35 for more details. © 2011 Directed Electronics. All rights reserved. 21 Commands Activates (or if On, deactivates) Smart Start.
Advanced Commands: (Level 4) Press and release the button 4 times. Full Silent Arm* level 4 Press and release The alarm arms, doors lock, and the siren chirps and parking lights flash 4 times. The FULL SILENT ARM text and beeps play to confirm and the System and Siren Status icons update. AUX 4 Press and release AUX Activates (or if On, deactivates) the Aux 4 output. The text and On tones or Off tones play to confirm.
Responder LC Configuration Operations of the Responder LC and how it communicates messages are set in the configuration Main Menu. Navigating menus and options Navigating menus and features, changing options, and exiting are performed using the remote control buttons. The following instructions discuss how to access and configure the settings. Button operation s AUX Access menu items 1. 2. 3. Press and hold the button for 8 seconds, the remote will beep once, MAIN MENU is displayed.
Main Menu The following Main Menu list of features is available for configuration of the remote control. Setup Remote menu: Keypad Lock Options: OFF , AUTO When OFF , the buttons do not lock and always perform a command when pressed. When set to AUTO , the remote buttons lock after a 20 second lapse between buttons presses to prevent unintentional operations. If a button is pressed when locked a fault tone plays as an alert followed by unlock instructions in the text field.
Off after 72 hours if the remote control is not used during this period. Just press any button to resume system monitoring. When set to ON it wakes up every few seconds to listen for pages from the system. When set to OFF it does not wake up to receive remote start or alarm trigger pages. Note: When OFF , responses are still received when a command is performed but alarm trigger pages will not be received.
Runtime Alert Options: ON , OFF The main unit will send a page to alert you when the runtime is about to expire. When set to ON , an alert is generated when the Remote Start Time-out message is received. When OFF , no alert output is emitted for the message. Car 2 Options: OFF , ON , HOME This remote can control two systems independently. When set to OFF , the Car2 select option is not available. When set to ON the remote can be set to control 2 systems.
Button Beep Options: ON , OFF When set to ON , the remote will emit a beep as confirmation of a button press. When set to OFF , beeps are not emitted for button presses.
Pair Remote: Remote Pair is a process where the Responder LC and the system in the vehicle learn each others encrypted identification, securing their communication from intruders. Please note that your remote controls come pre-programmed from the factory. Prepare the vehicle system to be Paired with a new remote 1. Open at least one of the vehicle’s doors. 2. Turn the key to the On position. 3. Within 5 seconds press and release 1 time the Control button on the Control Center. 4.
Demo mode: Power Off: When an extended period of non-operation is anticipated, turning the power off will preserve the battery charge. Press the button while POWER OFF is displayed. The status screen icons clear as the power off tones play, the remote is turned off. To turn the remote on, Press and hold the button for 3 seconds, the status screen icons refresh as the power on tones play. The remote also turns itself on and begins charging when the battery charger is connected.
Alarm Features Normal Arm Protection Status LED: The Control Center Status LED flashes as a visual indicator that your vehicle’s security system is active. Starter Kill: The Failsafe starter kill relay prevents the engine from starting Note May require additional parts and installation Sensor triggers: The onboard shock sensor can distinguish minor impacts from major impacts to the vehicle exterior.
Full Silent Arm Protection Sensor Warn-away, Sensor Full Trigger and Point of Entry activations will only send messages to the remote, with parking light flash and siren outputs defeated. Sensor Warn-away Messages When the remote receives a Sensor Warn-away message it emits 10 beeps (if on) and displays a sensor zone specific SENSOR WARN text for 30 seconds. Warn-away messages cannot be reviewed or displayed in reports.
Trigger Zone Fault Report When armed by remote command the system runs a status check of the alarm trigger zones. Faulty zones (usually caused by dome light delay or open trunk) are bypassed and reported via the control center LED and remote, while all other trigger zones remain active and are monitored to protect the vehicle. Should a faulty zone self correct (dome light turns off) it becomes active and is then monitored normally.
Table of Zones Zone # (led flashes) Zone Name 1 Trunk 2 Shock Sensor 3 Door 4 Sensor 2 5 Ignition 6 Hood Alarm Report when requested The Alarm Report displays the two most recent alarm triggers depending on the system state when requested. When disarmed, the report will display text to identify the two most recent triggers since the vehicle was last driven. When armed, the report will display text to identify the two most recent triggers since the system was armed.
Remote Start Features Pit Stop Mode To exit vehicle with engine running The system keeps the engine running during short trips into the house or convenience store. To perform Pit Stop: 1. 2. 3. 4. With the engine running, set the parking brake and release the foot brake. Press the button, the parking lights will turn on and the REMOTE START ON message will play on the remote control. Turn the key to off, and remove it from the ignition, the engine continues running for the programmed runtime.
4. then after a few seconds the remote plays the message. The vehicle is ready to drive. REMOTE START OFF Remote Start Safe-lock Remote start safe-lock makes sure the doors are locked while the engine is running and after, even if they are unlocked when remote start is activated. Door locks may require additional parts and labor. Disabling Remote Start Remote start can be disabled by moving the Toggle Switch to the Off position. If remote start is attempted while Off, the engine will not start.
Timer Start operation Activation begins a countdown timer as set by the installer (default 3 hours). When the timer expires the engine starts and the REMOTE START ON message is sent to the remote control. When the Remote start runtime expires the engine shuts off, the REMOTE START OFF message is sent to the remote control and the countdown timer restarts. This will repeat as many times as set by the installer (default 6 starts). Timer Start is exited after the final start.
Note Temperature report must be turned on by an authorized Directed dealer. Remote Start Time-out Alert During remote start a message is sent three minutes before and again at one minute before the engine turns off. The RUNTIME LOW text plays with tones as an alert to reset the runtime if desired. Manual Transmission Start (MTS mode) When installed into a manual transmission vehicle, the system requires that the MTS mode is properly set when parking.
6. 7. Exit the vehicle, close all the doors and arm the system. The engine turns off and after a few seconds, the REMOTE START OFF message plays to confirm. If the door is opened in Step 3 then the engine continues to run. Turbo Timer Mode The system keeps the engine running for the Turbo Timer runtime and can be activated by remote control or optional dash mounted activation button. 1. With the engine running, set the parking brake. 2.
Remote Start Error For user safety, the system must be properly configured or remote start will not activate. Refer to the table below for the screens and parking light flashes that will identify the configuration issue and resolution.
Remote and System Operations Passive Arming* Park and exit the vehicle, after the doors are closed the Passive arming countdown begins. The led flashes quickly and upon reaching 20 seconds the siren then chirps once. At 30 seconds the system arms itself. Anytime before the system arms you can re-enter the vehicle or open the trunk to load or unload items and, after closing passive arming resumes.
Valet Mode Valet mode can be entered and exited by performing the Remote Valet command or manually using the vehicle key and the control button. When entered, the alarm functions are defeated while the convenience features still operate normally. Arm and Disarm commands lock and unlock the doors while the VALET text and beeps play to confirm. Use 1. 2. 3.
Out of Range Each time a command is performed the remote will expect a command confirmation from the system. If a command confirmation is not received the out-of-range icon ( ) and a fault tone will play as an alert. No Remote Output Occasionally when a command is performed the remote may not generate a command confirmation output or Out of Range output. This indicates that the system received the command but it was an incomplete command (e.g.
1-way Companion Remote Control LED Command Buttons Function Button Level Direct Access x1 Button LEVEL 1 Arm/Lock Silent Arm x3 LEVEL 3 x4 LEVEL 4 Sensor Sensor Silent Full Silent Bypass Arm Arm Silent Disarm Remote Valet Car Finder Runtime Timer Start Smart Start Defogger AUX 2 AUX 3 AUX 4 (Panic) Disarm/ x2 LEVEL 2 Unlock Remote Start Reset Aux/Trunk AUX 1 Not Used Used to access function levels for Advanced Commands ( 1-Way AUX with multiplier in top row implies button
Using the 1 way companion remote The companion 1 way remote commands the system features as shown in the previous table, but without the message display of the Responder LC remote. Siren chirps and parking light flashes are used to indicate that a command has been received and activated as described in the Basic and Advanced command sections. Accessing Commands Similar to the Responder LC remote, Basic commands are performed when a command button is pressed directly.
Programming To enter; hold the button for 8 seconds, the remote emits one long beep and turns the LED on, the programming main menu has been accessed. To exit; press and release the button to go back and repeat to exit. 1 short and 1 long beep is emitted for each step back, the LED turns off when programming is exited. Sensor Adjust The button is used for sensor adjustment, to avoid unintended alarm triggers, it is recommenced that an authorized Directed dealer perform all sensor adjustments.
Battery Information (1-Way) The 1way companion remote is powered by one 3V coin cell lithium battery (PN CR-2032) that will last approximately one year under normal use. Battery Replacement 1 Side View 2 1. Using a small flat narrow object, push latch down towards battery tray while gently prying the tray outwards from both ends until released. Remove the tray from the remote control housing. Rear View Latch Battery Tray + 2.
System Expansion Options Controlling two vehicles (Car Select) The Responder LC and 1way companion remote can control systems in two different vehicles saving the need for multiple remote controls. This feature also allows for customized system configurations on each vehicle that has more than one driver. See Owner Recognition following for details. Owner recognition The system can be configured to recognize the remote used when disarming and change selected features to match the remote users preferences.
Driver door priority unlocking The door unlocking operation can be configured to emulate an OEM style of driver priority unlocking for added security during disarming. Auxiliary Channels The Auxiliary Channel outputs of this system can activate many of the convenience features found in today’s vehicles. Once a command is performed to activate a convenience feature the Responder LC displays text that matches the feature.
Battery Information (Responder LC) The Responder LC remote control is powered by an internal rechargeable battery that can be serviced only through an authorized Directed Electronics dealer. The information and precautions in this section can help maximize your battery’s life and usage in providing your Responder LC remote control with many years of trouble free operation. The battery information for the 1way companion remote control can be found in the 1-way Companion Remote Control section of this manual.
be charged at the earliest opportunity or failure to control the system may occur. Low Battery Alerts When disarming the system using a remote with a low battery the siren will emit one additional chirp as an alert. If confirmation chirps are programmed off, the system will still emit one chirp as an alert when disarming. After performing a command, LOWBAT and several beeps play on the Responder LC remote to indicate the battery needs to be charged.
Battery Disposal Directed Electronics cares about the environment. If you need to dispose of the battery, please do so in accordance with your municipal requirements for battery disposal. Battery © 2011 Directed Electronics. All rights reserved.
Glossary of Terms Document Terminology 52 Control Module The “brain” of your system. Usually hidden underneath the dash area of the vehicle. It houses the microprocessor which monitors your vehicle and controls all of the system’s functions. Responder LC (2-way Remote Control) A hand-held, remote control which operates the various functions of your system and receives messages and pages from the system.
Patent Information This product is covered by one or more of the following United States patents: Remote Start Patents: 5,349,931; 5,872,519; 5,914,667; 5,952,933; 5,945,936; 5,990,786; 6,028,372; 6,467,448; 6,561,151; 7,191,053; 7,483,783 Vehicle Security Patents: 5,467,070; 5,532,670; 5,534,845; 5,563,576; 5,646,591; 5,650,774; 5,673,017; 5,712,638; 5,872,519; 5,914,667; 5,952,933; 5,945,936; 5,990,786; 6,028,505; 6,452,484 Other patents pending. © 2011 Directed Electronics. All rights reserved.
Government Regulations This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules.
Control Center To satisfy FCC RF exposure compliance requirements, the device and its antenna must maintain a separation distance of 20 cm or more from the person’s body, except for the hand and wrists, to satisfy RF exposure compliance. This device complies with the Industry Canada Radio Standards Specification RSS 210.
Warning! Safety First Please read the safety warnings below before proceeding. Improper use of the product may be dangerous or illegal. Installation Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. If you have any questions, ask your retailer or contact Directed directly at 1-800-753-0600. Remote Start Capable When properly installed, this system can start the vehicle via a command signal from the remote control transmitter.
Before remote starting a manual transmission vehicle, be sure to: s Leave the vehicle in neutral and be sure no one is standing in front or behind the vehicle. s Only remote start on a flat surface s Have the parking brake fully engaged WARNING! It is the responsibility of the owner to ensure the parking/emergency brake properly functions. Failure to do so can result in personal injury or property damage.
GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMMEDIATELY CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AUTHORIZED Directed DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. This product is designed for fuel injected vehicles only.
Limited lifetime consumer warranty Directed Electronics.
ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE UNIT.