Troubleshooting guide
19
To save energy, the Economy mode Set Point is 11˚C (20˚F) below the Normal mode
Set Point.
The "Economy Mode" icon lights up when Economy mode is on.
Setting Economy mode:
1- Press Econo key.
2- The display will show Edxx
, with "xx" representing the Economy mode duration.
3- Use Warm or Cool key to change setting.
4- Press Econo key again.
5- The display will show ESxx
, with "xx" representing the delay before mode starts.
6- Use Warm and Cool arrows to change setting.
7- Press Econo key a third time to store settings.
40-minute Economy mode time-out: If you turn a pump, blower or light on while Economy
mode is on, the Economy mode will be interrupted and will only resume 40 minutes after
the system has turned the last active output off. The "Econ" message or "Economy Mode"
icon will flash, depending on your system configuration.
This function allows you to prevent unauthorized parameter settings. This feature is
especially helpful when young children have access to the keypad.
There are two modes you can choose from: Full lock or Partial lock. Full lock means that all
keypad functions are locked. Partial lock means that the basic functions of the spa will
remain accessible (pumps, blower and light), but it will be impossible to change the
temperature Set Point, to override the Economy mode or to enter the Programming mode.
When control pad is locked, the "Lock" icon will be displayed.
Locking your digital control pad:
1- Press and hold Econo key for 5 seconds.
2- The display will show LocP, with "P" representing Partial lock.
3- Release key and keypad will be in Partial lock mode. Keep key pressed down
for 5 more seconds if you want to be in Full lock mode. The "LocF" message
will then be displayed.
When control pad is locked, all automatic functions of the system run as usual. If a key is
pressed down, a "LocP" or "LocF" message will be displayed for 1 second. To unlock the
keypad, simply press and hold Econo key again for 5 seconds.
Summary of control panel parameters
Fdxx Filter cycle duration
FSxx Filter cycle delay
LocX Control pad lockout
Edxx Economy mode duration
ESxx Economy mode delay
P xx Purge cycles
Digital control pad lockout
LocP
LocF
"CLE" message
Filter cycles
Fd10
FS 6
Purge cycles
P 24
Boost filtration mode
Temperature unit
Inverted display
Water level sensor
Real-time clock
Ed12
ES20
Economy mode
Off mode
French, German and Spanish versions available upon request.
Press and hold Fiber Light key for 5 seconds to turn the system down (i.e. to set it to Off
mode) for 30 minutes. The "OFF" message is displayed. All keys are then disabled, unless you
press Fiber Light key to reactivate the system before the expiration of the 30-minute delay.
Press and hold Light key for 5 seconds to toggle between ˚C and ˚F.
Press and hold Filter key for 5 seconds to invert the display. If a power-up occurs, the
display always returns to default mode.
The system automatically performs 2 filter cycles per day, at 12-hour intervals. During a
filter cycle, Pumps 2 & 3 and blower run for one minute. Pump 1 then runs at low speed
for the remaining of the cycle and "Filter Cycle" icon lights up. (If system is equipped with
a circulation pump, all pumps and blower run for one minute. Circulation pump then
runs for the remaining of the cycle and "Filter Cycle" icon lights up.)
Setting filter cycles:
1- Press Filter key.
2- The display will show Fdxx, with "xx" representing the duration in hours.
3- Use Warm and Cool arrows to change setting.
4- Press Filter key again.
5- The display will show FSxx, with "xx" representing the delay before cycle
starts.
6- Use Warm and Cool arrows to change setting.
7- Press Filter key to store settings.
40-minute filter cycle time-out: If you turn a pump, blower or light on during a filter cycle, the
cycle will be interrupted and will only resume 40 minutes after the system has turned the
last active output off.
During a purge cycle, pumps and blower run for two minutes and "Filter Cycle" icon lights up.
Setting purge cycles:
1- Press Filter key.
2- The display will show P xx, with "xx" representing the currently set number
of daily purge cycles.
3- Use Warm and Cool arrows to change setting.
4- Press Filter key to store settings.
Note: The system may be installed to support 24-hour filtering with a circulation pump. In this
case, pressing Filter key will allow you to set the number of purge cycles per day.
This function allows you to speed up filtration after intensive use of your spa or to mix
chemicals. Simply keep Pump 1 key pressed down for 5 seconds. Pump 1 will run at high
speed for 45 minutes and "BOO" message will be displayed. Ozonator is also activated.
If the system is equipped with an optional water level sensor and the sensor detects an
insufficient level of water in the tub, the system will prevent pumps from starting and
will display the "H20" message. Pumps will be allowed to turn back on when water level
returns above sensor.
Every two weeks, the "CLE" message will be displayed indicating to clean the filter
(depending on your spa configuration). Press any key to reset the message.
Use Clock key to set real-time clock. The display toggles every 5 seconds
alternately showing the hourly time and the current water temperature.
CONTROL PANELS