“ILLUSION” FRAMELESS SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS PREPARATION Approximate Installation Time: What You’ll Need: • • • • • • • 60 minutes Box Cutter Clear Silicone Caulk Gun Electric Drill 3/16 Masonry Bit Flathead Screwdriver Phillips Head Screwdriver • • • • • • • Hacksaw Level Masking Tape Measuring Tape Pencil or Felt Tip Pen Rubber Mallet Safety Glasses Need some help? Call our customer service team at 1-800-874-8601 1
“ILLUSION” FRAMELESS SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS PACKAGE CONTENT CST 900S Sill 1 CST 901 Dam Sill 1 CST 903 Wall Jamb (Door Side) 1 CST 965 Wall Jamb (Stationary Panel) 1 C 914 C Drip Rail 1 C 956 C Seal Vinyl (Strike Post) 1 C 180 C Vinyl Strike Post 1 6-8114 1329 Installation Screw & Anchor 6 638 PHPT Adjustment Screw 3 CP 938 Setting Blocks 2 CP 965 B Wall Jamb Cap 2 98-45 Magnet 1 931 M Door Strike 1 C-5313-8 Ladder Pull / Handle 1 C 955 B Door
“ILLUSION” FRAMELESS SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS Door Assembly C 956 C C 180 C Support Arm (optional) CP 965 B CP 965 B Glass Panel CST 903 931 M Handle CST 965 C 955 B C 914 C CST 901 CP 952 B CST 900S CP 951 B CP 938 B Need some help? Call our customer service team at 1-800-874-8601 3
“ILLUSION” FRAMELESS SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS STEP 1. POSITION SILL AT CENTER OF SHOWER CURB Measure the base opening along the center of shower curb (as shown to the right). Then, trim Sill (CST 900S) exactly 1/16” shorter than your measurement. Be sure to double-check your measurements before trimming. Measure Base Opening Facing Outside Facing Inside STEP 2. IDENTIFY DOOR LOCATION.
“ILLUSION” FRAMELESS SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS STEP 3. PLACE WALL JAMBS AGAINST SHOWER WALLS • Temporarily tape the Sill (CST 900S) to shower curb, ensuring it does not move while taking your measurements. • Place Wall Jambs (CST 903 & CST 965) against shower walls, on the same side you’ve chosen to place the hinge. You’ll see Right versus Left Configurations below. • Use your pencil or felt tip pen to mark hole locations on shower walls. There are three holes per jamb.
“ILLUSION” FRAMELESS SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS RIGHT-SIDE CONFIGURATION IMPORTANT: All Coastal Shower Doors are pre-assembled for left-side configuration. To convert to rightside configuration, follow the steps below: You’ll notice two holes just above the top and bottom hinge pins. These are pre-cut for right-side door configurations. To convert your door to a right-side configuration, remove the screws from the pins, then install them into the other holes.
“ILLUSION” FRAMELESS SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS STEP 5. INSTALL STATIONARY GLASS PANEL CST 903 CST 900S 1. Place both Setting Blocks (CP 938) inside the Sill (CST 900S). They should fit nicely inside the crevice, and be spaced so the stationary glass panel rests evenly on each. CST 965 2. Run a bead of clear silicone the full length of the Wall Jamb (CST 965), on both the left and right inside walls of the jamb. 3.
“ILLUSION” FRAMELESS SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS STEP 6. TRIM AND PLACE DAM SILL 1. Measure the space between the hinge-side Wall Jamb (CST 903) and the stationary panel. Cut the Dam Sill (CST 901) to that measurement, minus 1/16”. CST 901 2. Snap the Dam Sill (CST 901) into the bottom Sill (CST 900S) with the upright lip toward the exterior. CST 901 Facing Outside MEASURE DOOR OPENING CST 900 Facing Inside 3.
“ILLUSION” FRAMELESS SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS STEP 8. INSERT DOOR/STRIKE POST VINYL AND MAGNET C 955 B 931 M 1. On the edge of the door glass, center the DoorStrike Vinyl (C 955 B) between the holes you’ll later use for installing the handle. 2. Place the Door Strike (931 M) over the Door-Strike Vinyl (C 955 B), with the thicker edge toward the inside of the shower. (This edge will work with your magnet.) Tap the Door Strike into place with a rubber mallet. C 180 C C 955 B 931 M 3.
“ILLUSION” FRAMELESS SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS STEP 9. SECURING DOOR ASSEMBLY IN PLACE When satisfied with the door operation (the Door Strike [931 M] should meet the magnet inside the Vinyl Strike Post and hold with even spacing between door edge and strike post from top to bottom), step inside the shower. Use your electric drill to secure the Hinge Post to the Wall Jamb (CST 903) using three Adjustment Screws (638 PHPT).
“ILLUSION” FRAMELESS SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS STEP 11. INSTALLING THE DOOR HANDLE K3 1. Insert the two clear plastic bushings into the holes on the glass. K2 K1 K2 2. Slip a washer (K2) onto the screw (K1). 3. From inside the shower, insert the screw through the bushing hole, then, slide a washer onto the screw (on the exterior side of the door). K4 4. Hand tighten the screw into the Handle (C-53138), then use the flathead screwdriver to tighten further.
“ILLUSION” FRAMELESS SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS STEP 13. INSTALL SUPPORT BAR (OPTIONAL) IMPORTANT: Support Bar (C-5401) is included with all LHL 5775 models, but is not included on LHL 4575 models. 1. Position the bracket over the top of the stationary glass panel using the vinyl pads to protect the glass on both sides. (Note: The further from the wall, the more secure the panel will be.) 2. Adjust bar position and mark hole location. 3.