PROFESSIONAL SERIES Remote Start with Keyless Entry Installation Guide CA 5051 2010 Audiovox Electronics Corporation. All rights reserved.
Table of Contents Before You Begin ...................................................................................... 3 Wire Connection Guide ........................................................................... 4 7 Pin Main Harness ................................................................................... 5 3 Pin Parking Light Harness ..................................................................... 7 6 Pin Start Harness ..............................................................
BEFORE YOU BEGIN PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting components or routing wires near moving parts Tape or loom wires under hood for protection and appearance Use grommets when routing wires through metal surfaces Use a Digital Multi Meter for testing and verifying circuits.
7 Pin Main Harness 3 Pin Parking Light Harness 6 PIN START 6 Pin Start Harness 1 PURPLE STARTER OUTPUT - MOTOR SIDE 2 RED BATTERY 12V ( + ) 3 ORANGE ACCESSORY 1 ( + ) 4 PINK/WHITE IGNITION 2 ( + ) 5 RED/WHITE BATTERY 12V ( + ) 6 PINK IGNITION 1 ( + ) 4 PIN ALTERNATE OUTPUT 4 Pin Alternate Harness 1 LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - ) 2 LT BLUE FACTORY ARM / PULSE AFTER START ( - ) 3 GREEN/WHITE PULSE AFTER SHUTDOWN ( - ) 4 BLACK/YELLOW PULSE DURING CRANK
7 Pin Main Harness 1 BLACK/WHITE ILLUMINATED ENTRY OUTPUT ( - ) This wire provides a ( - ) 500mA output for 30 seconds when the system is disarmed capable of driving relays. Locate the vehicle’s dome light or pin switch wire. Verification: This wire will register positive voltage or ground when the vehicle's dome light is turned ON. 2 BROWN/BLACK HORN OUTPUT ( - ) Locate the vehicle’s horn wire.
GM VATS Matching Value Resistor 87 Fused +12 Volt Battery Source BLUE/BLACK ActiveOutput Wire 87a 85 86 30 VATS Wire #2, WHITE or VIOLET/WHITE VATS Wire #1, WHITE or WHITE/BLACK Ignition Switch X CUT VATS Control Module Ignition 3 Accessory 2/3 Fused +12 Volt Battery Source Fused +12 Volt Battery Source 87 87 Jump To PINK Ignition Output Wire From Control Module 87a 85 86 BLUE/BLACK Active Output Wire 30 Jump To ORANGE Accessory Output Wire From Control Module PURPLE/WHITE 85 BLUE/BL
6 GRAY HOOD PIN INPUT ( - ) Install a Hood Pin Switch and connect to the GRAY wire. This connection is required for Remote Start. Verification: This wire when connected will register ground when the vehicle's hood is opened. Connect the GRAY wire to the hood pin. NOTE: Be sure to loom the wire, and seal the grommet. 7 BROWN/RED BRAKE INPUT ( + ) Locate the vehicle’s brake light wire at the brake pedal mounted switch. Verification: This wire registers positive voltage when the brake pedal is pressed.
6 Pin Start Harness 1 PURPLE STARTER OUTPUT ( + ) Locate the vehicle starter wire. Verification: This wire registers voltage only when the key is turned to the START position. Verification: The starter wire registers voltage when the key is turned to the START position. Connect the PURPLE wire to the vehicle starter wire. 2 RED BATTERY 12V ( + ) Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
5 RED/WHITE BATTERY 12V ( + ) Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch. Verification: This wire will register ( + ) voltage in all positions of the ignition switch. Connect the RED/WHITE wire to the constant 12 Volt battery wire. NOTE: Remove all fuses until all connections are made. 6 PINK IGNITION 1 ( + ) Locate the vehicle’s ignition wire at the ignition switch. Verification: This wire registers voltage when the key is turned to the ON (or RUN) position.
3 GREEN/WHITE PULSE AFTER SHUTDOWN ( - ) This wire will supply a ( - ) 200mA pulse after the remote start shuts down. This is typically used to re-lock the vehicle’s doors if they unlock upon remote start shutdown. It can also be used to pulse a door pin-switch wire to prevent the vehicle’s accessories from remaining on after remote start shutdown. 4 BLACK/YELLOW PULSE DURING CRANK ( - ) Locate the vehicle’s second starter (crank) wire at the ignition switch.
Negative Switching Locks All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: These wires will register ground when the Lock and Unlock switches are activated. Connect the GREEN and BLUE wires shown in the diagram below. Negative Locks: GREEN (-) Lock Output Lock Vehicle Door Lock Control Relays Unlock BLUE (-) Unlock Output Positive Switching Locks All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Reverse Polarity Locks (5-Wire Door locks) All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: These wires will rest at ground and register positive voltage when the Lock and Unlock switches are activated. Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPDT relays (not supplied).
Positive Multiplexed Locks All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: This wire will show variable positive voltage when the switch is activated. Please consult the wire and location chart for specific resistor values for your vehicle. Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPDT relays (not supplied).
Additional Ports Antenna / LED / Programming Port Mount the supplied antenna/receiver to a clear spot on the vehicle's windshield that will not block the driver's vision. A good location is usually high on the windshield near the rear view mirror. Be careful not to mount the antenna/receiver on any metallic window film, as this will effect system range. Route the antenna/ receiver cable to the control module and plug into the antenna port.
Set Up & Programming Transmitter Programming - Feature Bank 1 1. Turn the ignition ON. 2. Press and hold the valet/override button. 3. Within 10 seconds the system will chirp (3) three times. 4. Press 1 button of each transmitter you wish to program. 5. The system will respond with 1 chirp for each accepted transmitter. 6. Pressing the override button at anytime during programming will advance to the next bank. NOTE: The system will exit transmitter programming after 15 seconds of inactivity.
Feature Bank 1 - 3 Chirps Transmitter Programming Refer to transmitter programming. 16 2010 Audiovox Electronics Corporation. All rights reserved.
Tach Programming The unit will not operate unless a tach signal is programmed or the tachless option is turned ON. If an attempt is made to start the vehicle via the remote start without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and stored. If the tach rate is not properly programmed to the specific vehicle, the unit may not realize that the vehicle is running in certain instances and reengage the starter motor.
Feature Descriptions Feature Bank 2 - Security 1 - Silent Choice: Controls the normal arm/disarm chirps of the security system. ON - Silent arming/disarming upon first press of lock/unlock, pressing lock/ unlock a second time will activate the arm/disarm chirps respectively. The system will only sound the arm/disarm chirps upon a second press of the lock/unlock buttons. OFF - normal arm/disarm chirps upon the first press of lock/unlock.
3 - Ignition Controlled Locks: Control of door locks when the ignition is cycled ON or OFF. OFF - Door locks not activated by ignition. Lock and Unlock - Doors lock when ignition is turned on and unlock when ignition is turned off. Lock Only - Doors lock when ignition is turned on only. Unlock Only Doors unlock when ignition is turned off only. 4 - Horn Output Timing: Control the minimum horn pulse time in milli seconds, some vehicle will require a longer pulse to activate the factory horn.
4 - Tach Mode: Determines how the system monitors the engine running during remote start. Tach - Hard wired directly to the tach wire of the vehicle to monitor AC voltage. Tachless (Crank Average/Voltage) - Determines crank time by averaging the last 8 times the vehicle was started with the key and then monitors the change in voltage after remote start. Hybrid (Crank Average / No Voltage) - Determines crank time by averaging the last 8 times the vehicle was started with the key.
9 - Single / Double Pulse Start: Switches the remote start activation between a single or double press from the transmitter. 10 - IGN 2 Output: Programmable high current output. Ignition 2 - Ignition output during remote start. Accessory - Accessory output during remote start. Start / Crank - Crank output during remote start. 11 - 2 or 3 Hour Start: When activated, the remote start will activate and run for the programmed time and shut down every 2 or 3 hours.
Remote Start Shutdown Diagnostics If the remote start shuts down or fails to start, the parking lights will flash one of the patterns below indicating the shutdown input. To manually enter diagnostics and view the last shutdown, turn the ignition ON and press and release the button. LED FLASHES SHUTDOWN ZONE 3 Flashes Hood Input Brake Input 22 4 Flashes Remote Start Valet Mode 7 Flashes Tach not learned / Crank Average not learned 2010 Audiovox Electronics Corporation. All rights reserved.
2010 Audiovox Electronics Corporation. All rights reserved.
Audiovox Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.
