Owner Manual

ManualsBrandsCOLAMY ManualsExecutive Office ChairsExecutive Chair

Congratulations, you are now the owner

of a brand new STARSPACE chair!

Following this assembly guide and you

will nd a quick start guide to assemble

your STARSPACE chair. We highly

recommend checking out our Assembly

Videos as well for even more detailed

and visual instructions.

If you run into any difficulty during the

assembly, remember to check out the

assembly Video to see if you've missed

anything. If you're unable to resolve your

problems, drop us an email as well and

our support team will assist you.

ASSEMBLY GUIDE

PACKAGE LIST

ASSEMBLY INSTRUCTION

STEP 1: STEP 4:

STEP 5:

STEP 6:

STEP 7:

STEP 2:

STEP 3:

Step 1:

Turn the Star Base(8) upside

down, then press the Casters(9) into the

holes at the end of each base leg, insert

the Lift(6) into the center hole of the Star

Base, the Lift Cover(7) should be placed

over the Lift.

Step 2:

Align the Seat Plate(4) over the

pre-drilled holes underneath the Seat

Cushion, make sure that the front of the

seat plate is facing the front of the Seat

Cushion. Attach the Seat Plate(4) to

the Seat Cushion(2) using FOUR Botls

1/4*1”(10) , tighten all the bolts with the

Wrench(14), being careful not to miss-

thread the bolts or damaged the seat.

Step 3:

Turn the Seat Cushion upright and

align the center hole of the Seat Plate(4)

over the lift, then push the Seat Cushion(2)

down onto the lift rmly until the connection

is secure.

Step 4:

Attach Seat Cushion and Back

Cushion, align the Steel Plate over the pre-

drilled holes with Three Bolts 5/16*3/4”(11),

tighten all the bolts with the wrench(14).

Step 5:

Using the Seat Plate to tilt

135°angle Locking, then tighten the zipper

between seat cushion and back cushion,

then tilt angle back to 90°.

Step 6:

Attach the Arms(3) to the Seat

Cushion(2) and Back Cushion(1) with Four

Bolts M8*45mm(12), using the Wrench(14).

Step 7:

Press the Plastic Caps(13) into the

Arms holes to cover the bolts.

Note 1: Arm rests are labeled with an "L"

(left) or "R" (right) to show which sides they

should be placed on.

CAUTION:

Make sure all bolts and screws are fully

tightened before using chair. Lubricate

all moving parts and tighten all bolts/

screws every 6 month or whenever

needed.

Back Cushion *1

Back Pillow *1 Bolts 1/4*1” *4

Seat Cushion *1

Lift *1 Bolts 5/16*3/4” *3

Bolts M8*45mm *4

Arms *2

Lift Cover *1

Plastic Caps *4

Seat Plate *1

Star Base *1

Wrench *1Casters *5

1 5 10

6 11

7 12

8 13

149

MODEL:

BTX-290

INSTRUCTION MANUAL

any issues

Mind the important

safety information

Having a friend to help

makes assembly

extra-easy

Scan this QR Code to watch our

assembly video for the chair.

Before you

get started,

a few

pointers:

service@starspacechair.com

+1 628-222-2513

www.starspacechair.com

STARSPACE CHAIR

Watch

video

Summary of content (2 pages)

PAGE 1
MODEL: BTX-290 INSTRUCTION MANUAL ASSEMBLY GUIDE ASSEMBLY INSTRUCTION Congratulations, you are now the owner of a brand new STARSPACE chair! Step 1: Turn the Star Base(8) upside down, then press the Casters(9) into the holes at the end of each base leg, insert the Lift(6) into the center hole of the Star Base, the Lift Cover(7) should be placed over the Lift. Following this assembly guide and you will find a quick start guide to assemble your STARSPACE chair.
PAGE 2
INSTRUCTION MANUAL MODEL: BTX-290 INSTRUCTIONS FOR USE 1.Seat Height:Paddle-First lever on the right side To raise: While taking your weight off chair, lift lever up. To lower: While seated, lift lever up. * SAFETY AND MAINTENANCE Do not stand on the chair, Do Not use the chair as stepladder. Use this product for seating one person at a time. Do not use the chair unless all bolts and screws are firmly secured. Avoid contact with sharp objects to prevent puncturing the fabric.