Instructions / Assembly

ManualsBrandsCommercial Electric ManualsFlushmount Lights5/6 in./J-Box 12-Watt Dimmable White Integrated LED Round Flat Panel Ceiling Flushmount Light with Color Changing CCT

Table of Contents

Table of Contents ...................................2

Safety Information ..................................2

Warranty ..........................................2

Pre-Installation .....................................3

Tools Required ....................................3

Hardware Included .................................3

Installation ...................................... 4-6

Changing the Color Settings ..........................7

Safety Information

For your safety, always remember to:

□ Turn off the power supply at the fuse or circuit breaker box

before you install the ﬁxture.

□ Ground the ﬁxture to avoid potential electric shock and to ensure

reliable starting.

□ Double-check all connections to be sure they are

tight and correct.

□ Wear rubber soled shoes and work on a sturdy

wooden ladder.

□ Account for small parts and destroy packing material, as these

may be hazardous to children.

This ﬁxture is designed for use in a circuit protected by a fuse or

circuit breaker. It is also designed to be installed in accordance with

local electrical codes. If you are unsure about your wiring, consult a

qualiﬁed electrician or local electrical inspector, and check your local

electrical code.

WARNING: RISK OF SHOCK. House electric current can

cause painful shock or serious injury unless handled properly.

CAUTION: Turn off the main power at the circuit breaker

before installing the ﬁxture, in order to prevent possible shock.

NOTICE: All electrical connections must be in accordance with local

and National Electrical Code (N.E.C.) standards. If you are unfamiliar

with proper electrical wiring connections obtain the services of a

qualiﬁed electrician.

Remove the ﬁxture and the mounting package from the box and make

sure that no parts are missing by referencing the illustrations on the

installation instructions.

Warranty

LIMITED WARRANTY

This product is warranted to be free from defects in workmanship and materials for up to 5 years from date of purchase. If it fails to do so,

please contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.

WARNING: Risk of ﬁre. Use only on 120 volt 60Hz

circuits. Suitable for damp locations. Before installing

your lighting ﬁxture, thoroughly review enclosed in-

stallation manual. If you do not have sufﬁcient elec-

trical wiring experience, please refer to a do-it-your-

self wiring handbook or have your ﬁxture installed by

a qualiﬁed licensed electrician. All electrical connec-

tions must be in accordance with Local and National

Electrical Code (NEC) Standards. If ﬂickering occurs

in low level dimming, increase light level. Compatible

with most dimmers including Leviton 6681-IW, Lutron

S-600P and Lutron DVCL-153. Dimmable to 10% with

most dimmers.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures: Reorient or relocate the receiving antenna. Increase the separation between

the equipment and receiver. Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected. Consult the dealer or an experienced radio/

TV technician for help.