Instructions / Assembly

ManualsBrandsCommercial Electric ManualsOther5 in. White Recessed Baffle Kit

READ ALL THE INSTRUCTIONS

TOOLS & MATERIALS REQUIRED

QUESTIONS? CALL TOLL

FREE 1-800-345-0542

INSTALLATION & OPERATION INSTRUCTIONS –

5“ (12,7 CM) NON-IC RECESSED LIGHTING KIT

MODELS: CER5TR553WHP & CER5TR551WHP

WARNIN

:Fir

sco

ect

use

• Ladder

BX or NM Cable

• Keyhole Saw or 5 ½”

(14 0 cm) Hole Saw

• Pencil

UL Listed

GETTING STARTED

WARNING

First

disconnect

electricity

the

circuit

breaker

the

fuse

box. Disconnecting power by using the wall switch is not sufficient to

prevent electrical shock.

Choose the location for the fixture(s), keeping in mind the 6” (15,2 cm) depth

clearance, accessibility for the electrical supply, and the ½” (1,3 cm)

clearance from the joists, floor boards, or any other combustible material.

REMODEL INSTALLATION

MAKING THE HOLE/RUNNING THE SUPPLY WIRING TO THE HOLE

CAUTION

Before assembling your lighting fixture, refer to the “ELECTRICAL

CONNECTIONS” section. If you feel you do not have electrical wiring

experience, refer to a do-it-yourself wiring handbook or have your fixture

installed by a qualified licensed electrician.

NOTE: This fixture is a Non-IC type housing. Do not install insulation

ithi

(

)

(Fi

)

dditi

•

Cable

• BX or NM Cable

Connectors

(14

cm)

Hole

Saw

• Flathead Screwdriver

• Insulated Pliers

•

Listed

Electrical Tape

3 in. (7,6 cm) min. gap

Insulation

MAKING

THE

HOLE/RUNNING

THE

SUPPLY

WIRING

THE

HOLE

1. Cut a 5 ½” (14,0 cm) hole into the ceiling after choosing the appropriate

location. A template is provided to assist in making the hole. (Fig. 2)

Hole

Fig. 2

ithi

(

)

ous

ng.

(Fi

)

dditi

on,

ous

must be installed at least ½” (1,3 cm) away from any combustible

material, such as a wood joist or floorboard. The ceiling surface is

exempt from this requirement and may be in contact with the bottom

part of the housing.

Fig. 1

2. Clear out any insulation necessary to maintain the 3” (7,6 cm) spacing

specified in the “CAUTION” section found in the beginning of these

instructions. (See Fig. 1)

Keyhole saw

Out

oduct

use

in REM

DEL

app

cat

.In

IMPORTANT NOTE

3. Run armored cable (BX) o

non-metallic (NM) cable (also known as

Romex) from your circuit breaker or fuse panel to the 5 ½” (14,0 cm) hole,

providing 6” (15,2 cm) to 8” (20,3 cm) of slack extending below the hole.

Cablehavingupto12AWGwiringmaybeused.(Fig.3)(WARNING -

Use cables having wires rated 90°Cormore.)

Fig. 3

Out

bo ,

p oduct

use

app cat o s

remodel application, a ceiling surface already exists and there is no access

above the surface to the ceiling joists. To install this fixture, a hole must be

made in the existing ceiling from the room side. Then, electrical wiring must

be run to this hole and connected to the fixture. The fixture is, finally,

inserted into the ceiling hole, which secures itself to the ceiling surface,

using special remodel clips (provided). To use this product in NEW-

CONSTRUCTION applications, a Commercial Electric plaster frame and

Commercial Electric hanger bars must be purchased, separately. In a

new construction application, the ceiling surface has not yet been installed

and

the

ceiling

joists

are

still

exposed

and

accessible

Ceiling

Cable

Hole

BEFORE YOU BEGIN

1. To ensure the success of the installation, be sure to read these

instructions and review the diagrams thoroughly before beginning.

2. All electrical connections must be in accordance with local code and

ordinances. If you are unfamiliar with methods of installing electrical

wiring, secure the services of a qualified licensed electrician.

3. Before starting the installation, disconnect electricity at the circuit breaker

or the fuse box. Disconnecting power by using the wall switch is not

sufficient

prevent

electrical

shock

and

the

ceiling

joists

are

still

exposed

and

accessible

4. Proceed to the “ELECTRICAL CONNECTIONS” section.

1. Slide the housing through the hole opening. (Fig. 4)

MOUNTING THE HOUSING TO THE CEILING

sufficient

prevent

electrical

shock

4. Check if the power source is suitable for the added electrical load. Power

should be supplied by a 110/120 volt, 60 Hz single circuit. A standard 120

volt, 15 amp branch circuit is designed to carry a maximum load of 1800

watts. We recommend that the total wattage of all the lights and

appliances on that circuit, not exceed 80% or 1440 watts, of the maximum

electrical capacity.

5. This fixture is designed to be used on ceiling surfaces that are 3/8”

(1,0 cm), 1/2” (1,3 cm), or 5/8” (1,6 cm) thick. It cannot be used on

any other ceiling thickness.

Hole

Ceiling

UNPACK THE FIXTURE

Check the contents of the box. You should receive:

Fig. 4

Housing

• 1 – Housing (can,

junction box)

• 1 - Trim assembly

• 1 – Template

• 4 – Remodel clips (pre-

attached to housing)

•3 –Wire Nuts

Summary of content (9 pages)

PAGE 1
INSTALLATION & OPERATION INSTRUCTIONS – 5“ (12,7 CM) NON-IC RECESSED LIGHTING KIT MODELS: CER5TR553WHP & CER5TR551WHP QUESTIONS? CALL TOLL FREE 1-800-345-0542 READ ALL THE INSTRUCTIONS TOOLS & MATERIALS REQUIRED • Ladder • BX or NM Cable • BX or NM Cable Connectors • Keyhole Saw or 5 ½” (14 0 cm) Hole Saw (14,0 • Flathead Screwdriver • Insulated Pliers GETTING STARTED • Pencil • UL Listed Electrical Tape CAUTION Before assembling your lighting fixture, refer to the “ELECTRICAL CONNECTIONS” section.
PAGE 2
. When the “foot” of each remodel clip touches the ceiling, push the remodel clip through the “I” shaped opening. (Fig. 5) Housing Remodel clip Foot CEILING JOIST INSTALLATION 1. Raise the plaster frame and hanger bar assembly to the desired location between the two ceiling joists. Adjust the width of both hanger bars to the distance between the joists. Position the assembly so that the mounting clips of the hanger bars cup underneath the bottom edges of the joists.
PAGE 3
DROP CEILING INSTALLATION NOTE: Drop ceiling installations are similar to new construction installations, except the hanger bars are attached to the T-bars of a drop ceiling grid, instead of ceiling joists, as described below. T-BAR INSTALLATION (Fig. 12) 1. Install a ceiling tile onto the T-bar grid at the installation location. Using the provided template and a keyhole saw make a hole at the desired location in the ceiling tile. 2.
PAGE 4
INSTRUCCIONES DE INSTALACIÓN Y FUNCIONAMIENTO – JUEGO DE LUMINARIA EMPOTRADA TIPOS NO-IC DE 5" (10,2 CM) MODELOS: CER5TR553WHP & CER5TR551WHP LEER TODAS LAS INSTRUCCIONES HERRAMIENTAS Y MATERIALES NECESARIOS • Escalera • Serrucho de Punta Fina o Broca • Alicate Aislado • Cable BX o NM Sierra de 5 ½” ½ (14,0 (14 0 cm) • Lápiz • Conectores de Cable • 3 Destornillador de Cabeza • Cinta Aislante con BX o NM Clasificación UL Plana PRECAUCIÓN Antes de ensamblar tu lámpara, consulta la sección de “CONEXIONES ELÉ
PAGE 5
2. Cuando la cubierta esté casi completamente insertada, empuje los clips de remodelación a través de la abertura de la ranura en “I”. (Fig. 5) 1. Alza ensamblaje del marco de yeso y barra para colgar hasta la posición deseada entre las dos vigas del techo. Ajusta el ancho de las dos barras para colgar según la distancia entre las vigas. Coloca el ensamblaje de modo que las abrazaderas de montaje de las barras para colgar queden debajo de los bordes inferiores de las vigas.
PAGE 6
INSTALACIÓN EN TECHO FALSO NOTA: Las instalaciones de falso techo son similares a las instalaciones de nueva construcción, salvo las barras de suspensión están unidos a las barras en T de una rejilla de falso techo, en lugar de las vigas del techo, como se explica a continuación. INSTALACIÓN SOBRE BARRA EN T (Fig. 12) 1. Instala una placa de techo en el sistema de suspensión en T donde irá la lámpara. Usa la plantilla incluida y un serrucho de punta fina para abrir un orificio sitio deseado placa de techo.
PAGE 7
MODE D’INSTALLATION ET D’EMPLOI POUR LUMINAIRE ENCASTRÉ DE 12,7 CM (5 IN.) POUR PLAFOND NON ISOLÉ MODÈLES : CER5TR553WHP & CER5TR551WHP LISEZ TOUTES LES INSTRUCTIONS OUTILS ET MATÉRIAUX NÉCESSAIRES • Échelle • Câble BX ou NM • Connecteurs de câble BX ou NM • Scie à g guichet ou scie emportep pièce de 14,0 cm (5 ½ in.
PAGE 8
2. Lorsque le pied de chacune des fixations touche le plafond, poussez les fixations à travers les encoches en «I » jusqu’à ce qu’elles s’enclenchent. (Fig. 5) INSTALLATION SUR SOLIVES DE PLAFOND 1. Soulevez le cadre en plâtre et les barres de suspension vers l’emplacement désiré entre les deux solives de plafond. Ajustez la largeur des deux barres de suspension en fonction de la distance qui sépare les deux solives.
PAGE 9
INSTALLATION DANS UN PLAFOND SUSPENDU À NOTER : les installations dans plafond suspendu sont similaires aux installations nouvelles constructions, à l'exception des barres de suspension sont attachés à la Tbarres d'une grille de plafond suspendu, au lieu de solives de plafond, comme décrit cidessous. À NOTER : Outre le câble d’alimentation principal, la boîte de jonction peut accueillir un second câble pour alimenter un autre luminaire relié au même circuit.