Installation Guide

ManualsBrandsCommercial Electric ManualsOther5 in. and 6 in. White Recessed LED Trim with 4000K, 92 CRI

WARNING - RISK OF ELECTRIC SHOCK. DISCONNECT

MAIN POWER AT FUSE OR CIRCUIT BREAKER

BEFORE INSTALLING OR SERVICING THE FIXTURE.

LED5” & 6” RETROFIT TRIM INSTALLATION

INSTRUCTIONS - MODEL CER6730D

QUESTIONS? CALL TOLL

FREE 1-877-527-0313

5 in. – 7 in.

5 in. – 6 in.

PARTS

SOCKET ADAPTER

ASSEMBLY

RETROFIT TRIM

COMPATIBLE HOUSING

DIMENSIONS

FIG. 2

Please read carefully and save these instructions

as you may need them at a later date.

GENERAL: All electrical connections must be in accordance with

local and National Electrical Code (N.E.C.) standards. If you are

unfamiliar with proper electrical wiring connections obtain the

services of a qualified electrician.

Remove the trim from the box and make sure that no parts are

missing by referencing the PARTS illustrations.

THIS RETROFIT ASSEMBLY IS ACCEPTED AS A

COMPONENT OF A LED LUMINAIRE WHERE THE

SUITABILITY OF THE COMBINATION SHALL BE DETERMINED

BY CSA OR CANADIAN AUTHORITIES HAVING

JURISDICTION.

_________________________________________________

WARNING- RISK OF FIRE OR ELECTRIC SHOCK

FOR USE WITH HOUSING MODELS: INCANDESCENT

HOUSINGS – COMMERCIAL ELECTRIC HBR5ICAT,

HBR5ICRAT, HBR5, HBR5R, HALO H5T, H5RT, H5ICT,

H5RICAT, C7IC, C7ICR, C7ICA, C7ICRA, C7, C7R, C7S,

HBR5000SIC; HALO H7ICT, H7RICT, H7ICAT, H7RICAT, H7T,

H7RT, H27ICT, H27T, H27RT, H750ICAT, H750RICAT;

CORDELIA X5LICAT, X5LICRAT, HBR7LICAT, HBR7LICRAT;

CAPRI CR1, CRR1; DMF DH6ICATQ, DH6ICRATQ; ELCO

EL5ICA, EL5RICA; LITHONIA L5, L5R, EL7ICA, EL7RICA;

ELITE B5, B5R, B5IC, B5RIC, B6IC, B6RIC; JUNO IC22, IC22R;

LITHONIA L7X, L7XR; NORA NHIC-17QAT, NHRIC-17QAT;

PROGRESS P187-TG, P87-AT, P184-TG, P84-AT; SEA GULL

11018, 11028; THOMAS PS1, PS1-RM. HALO LED HOUSINGS

– H550ICAT, H550RICAT H750ICAT, H750RICAT.

• Do not alter, relocate, or remove wiring, lampholders, power

supply, or any other electrical component. Installation of the

retrofit assembly requires a person familiar with the

construction and operation of the luminaire’s electrical

system and the hazard involved. If not qualified, do not

attempt installation. Contact a qualified electrician.

• Do not make or alter any open holes in an enclosure of wiring

or electrical components during kit installation.

• To prevent wiring damage or abrasion, do not expose wiring

to edges of sheet metal or other sharp objects.

____________________________

ASSEMBLY AND INSTALLATION

1. If using a 5 inch housing, loosen the screws on the TORSION

SPRINGS (or FRICTION BLADES) and slide the brackets

inward. Re-tighten screws to secure TORSION SPRINGS

(or FRICTION BLADES) in place. (FIG. 2)

INCANDESCENT HOUSINGS

1. Unscrew the WING NUT inside the CAN to detach the

SOCKET BRACKET from the CAN. Disengage the SOCKET

from the SOCKET BRACKET. (FIG. 3)

2. Thread the SOCKET ADAPTER into the SOCKET. (FIG. 4)

FIG. 3 FIG. 4

Summary of content (9 pages)

PAGE 1
LED5” & 6” RETROFIT TRIM INSTALLATION INSTRUCTIONS - MODEL CER6730D Please read carefully and save these instructions as you may need them at a later date. GENERAL: All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician. Remove the trim from the box and make sure that no parts are missing by referencing the PARTS illustrations.
PAGE 2
3. Plug the FEMALE CONNECTOR of the RETROFIT TRIM onto the MALE CONNECTOR of the SOCKET ADAPTER ASSEMBLY. (FIG. 5) 4. If using TORSION SPRINGS, squeeze both TORSION SPRING arms together and insert into the TORSION SPRING SLOTS (or C-CLIPS) of the CAN. (FIG. 6) 5. Tuck all wires into the CAN and carefully push the RETROFIT TRIM into CAN.
PAGE 3
________ DIMMING Brand Dimming performance may depend on the dimmer, the dimmer range adjustment setting (for dimmers with brightness range adjustments), the wiring method, and/or the number of LED modules installed onto the dimmer circuit. For a complete list of compatible dimmers, please look up the item number listed on the cover of this instruction manual at http://www.homedepot.com/. Series Ariadni/Toggler C.L Diva C.L Skylark C.L Skylark Contour C.L Lumea C.L Lutron Maestro C.
PAGE 4
¿PREGUNTAS? LLAME GRATIS AL 1-877-527-0313 INSTRUCCIONES PARA LA INSTALACIÓN DEL ADAPTADOR DECORATIVO LED DE 5” y 6” MODELO CER6730D Lea cuidadosamente y guarde estas instrucciones ya que podría necesitarlas más adelante. GENERAL: Todas las conexiones eléctricas deben realizarse conforme a las normas locales y al Código Eléctrico Nacional (N.E.C. por sus siglas en inglés). Si no está familiarizado con las conexiones adecuadas de cableado eléctrico obtenga los servicios de un electricista calificado.
PAGE 5
3. Enchufe el CONECTOR HEMBRA del ADAPTADOR DECORATIVO al CONECTOR MACHO de la UNIDAD DEL ADAPTADOR DEL PORTALÁMPARAS. (FIG. 5) 4. Si usted está usando las ABRAZADERAS, apriete las ABRAZADERAS e inserte en las RANURAS (o RECEPTOR DE ABRAZADERA) de el PORTALÁMPARAS. 5. Mete todos los cables en el PORTALÁMPARAS y empuje con cuidado la reconversión ADAPTADOR DECORATIVO en PORTALÁMPARAS.
PAGE 6
__________________________ ____ REGULADOR DE INTENSIDAD LUZ Rendimiento de atenuación puede depende del regulador, la configuración de atenuación, rango de ajuste (que los reguladores con ajustes rango de brillo), el método de cableado, y/o el número de módulos LED instalados en el circuito del atenuador. Para una lista completa de reguladores compatibles, por favor vea el manual de instrucciones bajo el modelo que aparece en la primera pagina de este manual en http://www.homedepot.com/.
PAGE 7
MODE D’INSTALLATION POUR GARNITURE DE DES QUESTIONS? RÉNOVATION AVEC MODULE DEL DE 12,70 et 15,24 APPELEZ SANS FRAIS AU CM - MODÈLES CER6730D 1-877-527-0313 Veuillez lire ces instructions attentivement et les conserver pour pouvoir les consulter au besoin. AVERTISSEMENT – RISQUE DE DÉCHARGE ÉLECTRIQUE. COUPEZ LE COURANT AU NIVEAU DU DISJONCTEUR OU DE LA BOÎTE DE FUSIBLES AVANT D’INSTALLER OU D’EFFECTUER L’ENTRETIEN DU LUMINAIRE.
PAGE 8
3. Branchez le CONNECTEUR FEMELLE de la GARNITURE DE RÉNOVATION dans le CONNECTEUR MÂLE du SUPPORT ADAPTATEUR. (FIG. 5) 4. Si vous utilisez des RESSORTS DE TORSION, serrez les deux pattes à RESSORTS DE TORSION l’une contre l’autre et insérez-les dans les FENTES DE RESSORT DE TORSION (ou SUPPORTS DE RÉCEPTION) du BOÎTIER. (FIG. 6) 5. Rentrez tous les fils dans le BOÎTIER et poussez doucement la GARNITURE DE RÉNOVATION dans le BOÎTIER.
PAGE 9
__________________________ GRADATION DE L’INTENSITÉ LUMINEUSE Marque Ariadni/Toggler C.L Gradation des performances peut dépend du gradateurs, le réglage du gradateur Plage de réglage (pour les gradateurs avec des ajustements de la plage de luminosité), la méthode de câblage, et / ou le nombre de modules DEL installés sur le circuit de gradateur. Pour une liste complète des gradateurs compatibles, consultez le modèle sur la couverture de ce manuel d'instructions à http://www.homedepot.com/.