Instructions / Assembly

ManualsBrandsCommercial Electric ManualsLighting6 in. White Integrated LED Recessed Gimbal Trim with Pivot and Rotate

WARNING - RISK OF ELECTRIC SHOCK.

DISCONNECT MAIN POWER AT FUSE OR CIRCUIT

BREAKER BEFORE INSTALLING OR SERVICING

THE FIXTURE.

QUESTIONS? CALL TOLL

FREE 1-877-345-0542

Please read carefully and save these instructions, as

you may need them at a later date.

GENERAL: All electrical connections must be in accordance with local

and National Electrical Code (N.E.C.) standards. If you are unfamiliar

with proper electrical wiring connections obtain the services of a

qualified electrician.

Remove the trim from the box and make sure that no parts are missing

by referencing the PARTS illustrations.

THIS RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF

A LED LUMINAIRE WHERE THE SUITABILITY OF THE

COMBINATION SHALL BE DETERMINED BY CSA OR CANADIAN

AUTHORITIES HAVING JURISDICTION.

__________________________________________

WARNING- RISK OF FIRE OR ELECTRIC SHOCK

FOR USE WITH HOUSING MODELS: INCANDESCENT HOUSINGS –

COMMERCIAL ELCETRIC C7IC, C7ICR, C7ICA, C7ICRA, C7, C7R,

C7S, HBR5000SIC; HALO H7ICT, H7RICT, H7ICAT, H7RICAT, H7T,

H7RT, H27ICT, H27T, H27RT, H750ICAT, H750RICAT; CORDELIA

HBR7LICAT, HBR7LICRAT; CAPRI CR1, CRR1; ELCO EL7ICA,

EL7RICA; JUNO IC22, IC22R; LITHONIA L7X, L7XR; THOMAS PS1,

PS1-RM; DMF DH6ICATQ, DH6ICRATQ; NORA NHIC-17QAT, NHRIC-

17QAT; ELITE B6IC, B6RIC; SEA GULL 11018, 11028. HALO LED

HOUSINGS – H750ICAT, H750RICAT.

• Do not alter, relocate, or remove wiring, lampholders, power supply,

or any other electrical component. Installation of the retrofit

assembly requires a person familiar with the construction and

operation of the luminaire’s electrical system and the hazard

involved. If not qualified, do not attempt installation. Contact a

qualified electrician.

• Do not make or alter any open holes in an enclosure of wiring or

electrical components during kit installation.

• To prevent wiring damage or abrasion, do not expose wiring to

edges of sheet metal or other sharp objects.

____________________________

ASSEMBLY AND INSTALLATION

1. If the installed housing does not have TORSION SPRING SLOTS or

C-CLIPS (FIG. 3), then remove the SCREWS securing the

TORSION SPRINGS to the HEATSINK. Attach the FRICTION

BLADES (included) to the same location using the SCREWS that

were previously removed. (FIG. 6)

INCANDESCENT HOUSINGS

1. Unscrew the WING NUT inside the CAN to detach the SOCKET

BRACKET from the CAN. Disengage the SOCKET from the

SOCKET BRACKET. (FIG. 2)

2. Thread the SOCKET ADAPTER into the SOCKET. (FIG. 3)

3. Plug the FEMALE CONNECTOR of the RETROFIT TRIM onto the

MALE CONNECTOR of the SOCKET ADAPTER ASSEMBLY. (FIG.

4. If using TORSION SPRINGS, squeeze both TORSION SPRING

arms together and insert into the TORSION SPRING SLOTS (or

RECEIVER BRACKETS) of the CAN. (FIG. 5)

5. Tuck all wires into the CAN and carefully push the RETROFIT TRIM

into CAN. (NOTE: To provide enough room in shallow cans, carefully

position SOCKET ADAPTER and SOCKET adjacent to the long side

of the LED DRIVER prior to inserting the RETROFIT TRIM into the

CAN.) (FIG. 5)

LED HOUSINGS

1. Plug the FEMALE CONNECTOR of the RETROFIT TRIM onto the

MALE CONNECTOR of the HALO HOUSING. (FIG. 4)

2. If using TORSION SPRINGS, squeeze both TORSION SPRING

arms together and insert into the TORSION SPRING SLOTS (or

RECEIVER BRACKETS) of the CAN. (FIG. 5)

LED 6” RETROFIT TRIM INSTALLATION

INSTRUCTIONS - MODEL CER6742B

REV 24-JUL-17

5 in. – 7 in.

6 in.

FIG. 2 FIG. 3

PARTS

SOCKET ADAPTER ASSEMBLY

RETROFIT TRIM

COMPATIBLE

HOUSING DIMENSIONS

FIG. 4

FIG. 5

FIG. 6

FIG. 1

Summary of content (6 pages)

PAGE 1
LED 6” RETROFIT TRIM INSTALLATION INSTRUCTIONS - MODEL CER6742B Please read carefully and save these instructions, as you may need them at a later date. WARNING - RISK OF ELECTRIC SHOCK. DISCONNECT MAIN POWER AT FUSE OR CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING THE FIXTURE. GENERAL: All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.
PAGE 2
3. Tuck all wires into the CAN and carefully push the RETROFIT TRIM into CAN. (NOTE: To provide enough room in shallow cans, carefully position SOCKET ADAPTER and SOCKET adjacent to the long side of the LED DRIVER prior to inserting the RETROFIT TRIM into the CAN.) (FIG. 5) ________________________ LIGHT DISTRIBUTION MAP ±180 150 -150 ________ DIMMING For an up-to-date list of compatible dimmers, look up item number at www.homedepot.com or www.homedepot.ca.
PAGE 3
INSTRUCCIONES PARA LA INSTALACIÓN DEL ADAPTADOR DECORATIVO LED DE 6” MODELO CER6742B Lea cuidadosamente y guarde estas instrucciones ya que podría necesitarlas más adelante. ADVERTENCIA: RIESGO DE DESCARGA ELÉCTRICA. DESCONECTE EL SUMINISTRO ELÉCTRICO DE LA CAJA DE FUSIBLES O LOS INTERRUPTORES DE CIRCUITO ANTES DE INSTALAR O DAR MANTENIMIENTO A LA UNIDAD.
PAGE 4
3. Meta todos los cables en el PORTALÁMPARAS y empuje con cuidado el ADAPTADOR DECORATIVO en PORTALÁMPARAS. (NOTA: Para proporcionar suficiente espacio en los PORTALÁMPARAS de poca profundidad, con cuidado posicione el ADAPTADOR DEL ZÓCALO y el enchufe al lado largo de la CONTROLADOR antes de insertar el RECONVERSIÓNADO ADAPTADOR DECORATIVO en el PORTALÁMPARAS). (FIG.
PAGE 5
MODE D’INSTALLATION POUR GARNITURE DE RÉNOVATION AVEC MODULE DEL DE 15,24 CM MODÈLES CER6742B Veuillez lire ces instructions attentivement et les conserver pour pouvoir les consulter au besoin. GÉNÉRALITÉS: Tous les raccordements doivent être effectués conformément aux exigences des règlements locaux et du code national de l’électricité (CNE). Si vous ne connaissez pas les principes de raccordement d’une installation électrique, veuillez utiliser les services d’un électricien certifié.
PAGE 6
2. Si vous utilisez des RESSORTS DE TORSION, serrez les deux pattes à RESSORTS DE TORSION l’une contre l’autre et insérezles dans les FENTES DE RESSORT DE TORSION (ou SUPPORTS DE RÉCEPTION) du BOÎTIER. (FIG. 5) 3. Rentrez tous les fils dans le BOÎTIER et poussez doucement la GARNITURE DE RÉNOVATION dans le BOÎTIER.