Instructions / Assembly
Item
Model #
Installation
Installation
Canopy screw
TOOLS REQUIRED
Hardware not shown to actual size.
HARDWARE INCLUDED
2
Installing the mounting bracket assembly
Adjusting the knob
3
Making the electrical connections
Safety Information
PACKAGE CONTENTS
Pre-Installation
Pre-Installation
BB
CC
NOTE:
Make sure the power is off.
□
Pull the supply wires down out of the outlet box.
□
Fasten the mounting bracket assembly (CC) to the
outlet box with the outlet box screws (AA).
to adjust the light to your desired direction.
□
□
□
□
□
Ladder Gloves
Safety goggles
Phillips screwdriver Electrical tape
Wirestripper
C
D
B
Wrap electrical tape (not included) around the wire
connectors (BB), and ensure they are secure.
Push all excess wire and wire connections back
into the outlet box.
□
Attach the ground wire from the outlet box to the ground
screw on the mounting bracket (CC), which is green and
marked "GND".
AA
Outlet box
screws
x 2
x 2
BB
Wire connectors
x 3
Mounting bracket
assembly
x 1
Outlet box
CC
AA
CC
DD
DD
to the negative wires from the supply circuit, the positive
from the supply circuit, and the ground wire from
the wire connectors (BB).
4
Attaching the canopy to the wall or ceiling
A
A
CC
CC
DDEE
□
Raise the canopy (A) up to the outlet box.
□
□
Secure the canopy (A) to the mounting bracket assembly
(CC) screws using the canopy screws (DD) and plastic
washer (EE) provided.
Adjust the length of the mounting bracket assembly
(CC) screws and hex nuts if necessary.
Plastic washer
x 2
EE
Warranty
USE AND CARE GUIDE
LED LIGHT FIXTURE
5-YEAR LIMITED WARRANTY
or workmanship, the product must be returned, with a copy of the bill of sale as proof of purchase, to the
original place of purchase. The manufacturer will, at its option, repair, replace, or refund the purchase
becoming damaged due to misuse, accidental damage, improper handling and/or installation, and
exclusions or limitations on an implied warranty, so the above exclusions and limitations may not apply.
A
Installation
C
D
D
B
GG
#1002076258
DW8899ABZ-B
[CC&DD Preassembled on the canopy (A)]
1
Removing the mounting bracket
assembly
□
Loosen the canopy screws (DD) and separate
the mounting bracket assembly (CC) from the
Waterproof silicon
Mounting surface
Canopy
5
□
between the canopy and mounting surface,
waterproof silicon, caulk or gel should be applied to
seal any gaps around the junction point.
□
□
□
Read all instructions prior to beginning the
installation process.
Make sure the power is turned off at the
electrical panel box before beginning your
installation. Turning the power off at the wall
shock.
IMPORTANT SAFETY INSTRUCTIONS
(Save These Instructions)
square x 2-1/8 in. deep metal octagon outlet box.
The box must be directly supported by the
building structure.
□
All electrical connections must be in accordance
with local codes and the National Electrical Code.
If you are unfamiliar with methods of installing
licensed electrician.
□
□
□
□
□
□
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
compliance could void the user’s authority to operate the equipment.
7
6
□
□
Care and Cleaning
□
removing the fuse at the fuse box.
□
□
CAUTION: Do not use chemical solvents or harsh
may occur.
Use a dry or slightly dampened, clean cloth (use clean water, never use a solvent) to wipe the
To disable the dusk-to-dawn photocell (D), keep the photocell cap (GG)
over the dusk-to-dawn photocell (D). This will prevent the dusk-to-dawn
photocell (D) from controlling the ON/OFF function, and will allow the ON/OFF
function to be directly controlled by the wall switch.
CAUTION:
Keep the lamp away from
materials that may burn.
WARNING: This lighting is suitable for wet
locations.
CAUTION:
The LEDs in this product
are not replaceable.
WARNING: Keep the photocell covered until
installation is complete.
Troubleshooting
Problem Possible Cause Solution
The power is off.
Make sure the power supply is on.
There is a faulty wire
connection.
There is a faulty switch. Test or replace the switch.
The light will not
illuminate.
Light cycles or
The light does not
automatically turn off
during daylight hours.
The photocell is covered.
The photocell is detecting
light nearby.
to keep their light don’t interfere the
photocell.
The Dusk to Dawn feature
was bypassed.
Follow the operation steps and Reinstate
the Dusk to Dawn feature.
The photocell is in a dark
or shaded area.
Make the photocell get the direct sunlight.
Remove the cover on the photocell or
Clean the photosensor.
Check the wiring. Contact a qualied and
licensed electrician if you are not comfortable
troubleshooting wiring problems.
CAUTION:
Do not connect this light xture
to a dimmer switch.
Operation
□
The xture contains a photocell with Dusk to Dawn feature,that automatically turns the lights on at
dusk and off at dawn.
□
□
Water Proof Seal
x 1
FF
Photocell
sleeve
Checking the ON/OFF function of the light
To activate the dusk-to-dawn photocell (D), remove the photocell cap (GG)
from the photocell (D) and make sure it is installed in direct view of sunlight.
Optional: Installing the photocell sleeve
8
□
If the light cycles or flashes on and off, then place the
photocell sleeve (FF) to cover the photocell of fixture.
FF
Part Description
Fixture body
B
A
Canopy
Quantity
1
1
Knob
C
D
1
1
Photocell
THANK YOU
We appreciate the trust and condence you have placed in Commercial Electric through the purchase of this LED light
xture. We strive to continually create quality products designed to enhance your home. Visit us online to see our
full line of products available for your home improvement needs. Thank you for choosing Commercial Electric!
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-877-527-0313
Questions, problems, missing parts? Before returning to store,
HOMEDEPOT.COM
Contact the Customer Service Team at 1-877-527-0313 or visit www.homedepot.com.
call Commerial Electric Customer Service
Retain this manual for future use.
Photocell
cap
x 1
GG
NOTE:
a.
When installing during the day, take out the photocell cap/sticker (GG) from the
accessory bag to cover the photocell. The light should turn on after a slight
delay. Please made sure to remove the photocell cap/sticker (GG) after the light
can work normally, otherwise the light does not shut off during the daytime.
b.
If the light does not shut off during the daytime, please shine the photocell
with the ashlight for 2-3 minutes, the light will turn off after two minutes, this
means that the photocell did not receive enough illuminate, please re-move the
light so that the photocell can receive the illuminate.
Forced switch operation principle (In the case of power failure or the photocell is stuck on):
Operate the switch within 4 seconds, ON (1st time) - OFF (1st time) - ON (2nd time) - OFF (2nd time) -
ON (3rd time), enter Strong open state, press again to enter OFF (3rd time). This cycle, repeated again
and again.
If the user does not know which step the xture is in, shut it down, stay for half a minute, perform
the above operation on the switch, and reach ON (3rd time) to enter the strong opening.
NOTE:
minimum of 4 feet off the ground, and should
be located at least 20 inches below any
overhang.
This xture should be mounted a